Instruction Manual for luminii models including: KBX-X-X-DW, Kurba Medium Horizontal Dynamic White, KBX-X-X-DW Kurba Medium Horizontal Dynamic White, Horizontal Dynamic White
Kurba Medium Horizontal Dynamic White – Luminii
Linear – Luminii
Kurba Medium Dome Horizontal Dynamic White – Luminii
File Info : application/pdf, 7 Pages, 943.99KB
DocumentDocumentInstallation Instructions - Kurba Dynamic White Models KBX-X-X-DW Please read all instructions prior to installation and keep for future reference! REV0.4 07272022 1 / 7 7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 info@luminii.com www.luminii.com Kurba Horizontal Kurba Vertical *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE Installation Instructions - Kurba Dynamic White Models KBX-X-X-DW Please read all instructions prior to installation and keep for future reference! 1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN. 2. USE ONLY WITH CLASS 2 POWER UNIT 3. 24 VOLTS DC 4. SUITABLE FOR WET LOCATIONS 5. SURFACE MOUNT ONLY REV0.4 07272022 2 / 7 7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 info@luminii.com www.luminii.com CAUTION: Reference diagram below on Can and Can-nots, when it comes to installing the Kurba Horizontal & Vertical! Kurba Horizontal (KBM-XX) CAN Bend LED in these positions to avoid damage Kurba Vertical (KBL-XX) CAN Bend LED in these positions to avoid damage LED surface (gray color) 2.5" radius minimum 2.5" radius minimum LED surface (gray color) Bend in this direction only Bend in this direction only CANNOT Twisting or bending LED in these positions will cause damage to the LED LED surface (gray color) LED surface (gray color) CANNOT Twisting or bending LED in these positions will cause damage to the LED Twisting Kurba will cause damage to the LED LED surface (gray color) LED surface (gray color) Twisting Kurba will cause damage to the LED Do not make sharp bends near the endcap Bending in the same direction as the LED will cause damage to the LED Do not make sharp bends near the endcap Bending in the same direction as the LED will cause damage to the LED *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE Installation Instructions - Kurba Dynamic White Models KBX-X-X-DW Please read all instructions prior to installation and keep for future reference! 1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN. 2. USE ONLY WITH CLASS 2 POWER UNIT 3. 24 VOLTS DC 4. SUITABLE FOR WET LOCATIONS 5. SURFACE MOUNT ONLY REV0.4 07272022 3 / 7 7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 info@luminii.com www.luminii.com 1 NOTE: Prior to installation all 24VDC wires must be present within 72" of the installation. Refer to the power supply installation instruction for additional information. NOTE: More than one person is recommended for this installation. 1.1 Once the location or pattern is determined for Kurba to be installed, start off by marking the area. Amount of brackets may vary dependant upon pattern. Reference diagrams below. Straight run with mounting channel KURBA Body mounting channel spring clip A.1 mounting channel A.1 Line up the spring clips to the mounting holes, followed by placing the mounting channel to the surface. Make sure its straight by using a level. A.2 Secure channel to the surface by tightening all the provided screws. If mounting to something other than wood, we recommend using the proper hardware. endcap Curved run with mounting channel mounting bracket 8"away (maximum) screw B .2 B.1 Determine the shape of the Kurba layout, then mark thel pattern onto the surface. Then, place a mounting bracket every 8"(minimum). The pattern may vary dependant upon the amount of curves. B.2 Secure the mounting brackets to the surface by tightening the screw. If mounting to something other than wood, we recommend using the proper hardware. *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE Installation Instructions - Kurba Dynamic White Models KBX-X-X-DW Please read all instructions prior to installation and keep for future reference! 1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN. 2. USE ONLY WITH CLASS 2 POWER UNIT 3. 24 VOLTS DC 4. SUITABLE FOR WET LOCATIONS 5. SURFACE MOUNT ONLY 2 Straight run with mounting channel REV0.4 07272022 4 / 7 7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 info@luminii.com www.luminii.com 2.1 2.1 Curved run with mounting brackets 2.1 Carefully push the Kurba onto the channel or mounting brackets, then press in completely to secure in place. 8"away (maximum) *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE Installation Instructions - Kurba Dynamic White Models KBX-X-X-DW Please read all instructions prior to installation and keep for future reference! 1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN. 2. USE ONLY WITH CLASS 2 POWER UNIT 3. 24 VOLTS DC 4. SUITABLE FOR WET LOCATIONS 5. SURFACE MOUNT ONLY Wiring Diagrams Using DMX LED power supply REV0.4 07272022 5 / 7 7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 info@luminii.com www.luminii.com To Controller GND D+ D- DMX cables (For DMX cable, use Belden 9829, 9842 or CAT5 shielded twisted pair cabling or equivalent) to the next LED Driver PSDMX-3X96-24 DMX LED Driver WW + CW Load Ground Neutral INPUT 120 - 277VAC Kurba dynamic white Using non dimming LED power supply, receiver and controller Operations to Controller DDW-MC Wireless Controller To on/off Switch Load Ground INPUT Neutral 120 - 277VAC PSV-XX-24-U2ND-XX Non Dimming LED power supply 24V DC+ 24V DC- RGBW-RC-R RGBW Receiver Kurba dynamic white *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE Installation Instructions - Kurba Dynamic White Models KBX-X-X-DW Please read all instructions prior to installation and keep for future reference! 1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN. 2. USE ONLY WITH CLASS 2 POWER UNIT 3. 24 VOLTS DC 4. SUITABLE FOR WET LOCATIONS 5. SURFACE MOUNT ONLY Using warm dim LED power supply PS010WD-96-24 + Warm Dim LED Driver REV0.4 07272022 6 / 7 7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 info@luminii.com www.luminii.com Load Ground Neutral Kurba dynamic white Using tunable white LED power supply Controller 1: 0-10V+for intensity + Controller 2: 0-10V for color temperature PS010TW-96-24 Tunable White LED Driver Load Ground Neutral INPUT 120 - 277VAC Kurba dynamic white *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE Installation Instructions - Kurba Dynamic White Models KBX-X-X-DW Please read all instructions prior to installation and keep for future reference! 1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN. 2. USE ONLY WITH CLASS 2 POWER UNIT 3. 24 VOLTS DC 4. SUITABLE FOR WET LOCATIONS 5. SURFACE MOUNT ONLY Using non dimming LED power supply, decoder and controller DW-DMX Dynamic White DMX Controller REV0.4 07272022 7 / 7 7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 info@luminii.com www.luminii.com PSV-XX-24-U2ND-XX Non Dimming LED power supply To on/off Switch Neutral INPUT Ground 120 - 277VAC Load 24V DC+ 24V DC- DDMX-RGBW DMX Decoder Kurba dynamic white Using non dimming LED power supply and decoder To on/off Switch Neutral INPUT Ground 120 - 277VAC Load PSV-XX-24-U2ND-XX Non Dimming LED power supply 24V DC+ 24V DC- DDMX-RGBW DMX Decoder Kurba dynamic white *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE