Instructions for DELL models including: P2723QE LCD Monitor, P2723QE, LCD Monitor
210-BDFZ: Dell 27" Monitor P2723QE 4K USB-C Hub - Black | Convena.com
Teardown Instruction Teardown Instruction LCD Monitor P2723QE/QEf 1 Teardown Instruction Service Manual Versions and Revision No. Version Release Date Revision 1 1.0 2021/11/08 Initial Release 2 1. Remove Rear Cover Screw Remove screws "1~4" on rear cover with electric screwdriver. Torque: 12.0 ± 0.5Kgf/cm Teardown Instruction 4. Remove Keypad: a. Remove keypad cable in sequence of "1, 2, 3" b. Remove screws "5, 6" with electric screwdriver. Screwdriver torque: 2.5 ± 0.5 Kgf/cm c. Separate keypad and rear cover 2. Remove Rear Cover 1: Panel side down, remove rear cover with both hands in sequence of "1->2->3", then "1->4->5->6" 5. Remove Light Bar and USB Cable: a. Remove acetate tape "1", grasp on pin, then remove light bar cable horizontally b. Remove aluminium foil "2", lift up USB pin cover, then remove USB cable 3. Remove Rear Cover 2: a. Set up rear cover, remove mylar "1" b. Remove keypad cable "2" c. Remove light bar "3" 6. Remove Chassis and USB Board Screws a. Remove chassis screws "1~4" and USB board screw "5" with electric screwdriver. Torque: 3.5 ± 0.5Kgf/cm b. Remove USB board 3 Teardown Instruction 7. Remove FFC: 10. Remove Front Trim Screws 1: S7 a. Remove aluminium foil "1" S10 a. Remove screws "1~11" on mid frame with b. Lift up FFC cover, grasp on pinch, then remove electric screwdriver. Screwdriver torque: 3.5 ± light bar cable horizontally 0.5 Kgf/cm b. Separate mid frame from panel 8. Remove PCBA 1: a. Remove mylar b. Remove screws "1~9" with electric screwdriver. Torque: 5.5 ± 0.5Kgf/cm 11. Remove Front Trim Screws 2: a. Remove screws "1~3" with electric screwdriver. Screwdriver torque: 0.8 ± 0.1 Kgf/cm b. Separate front trim from mid frame 9. Remove PCBA 2: a. Remove Power Board and IF Board b. Sperate Power Board and IF Board 12. Remove LED a. Remove LED from mid frame with jig. b. Separate lens from LED Board 4 Remove electrolyte capacitor >25mm height (red mark) from printed circuit boards. S13 Cut the glue between bulk cap and PCBA with knife ensure cutting path within the glue, don't touch bulk cap and PCBA. Teardown Instruction Take out the capacitor pin solder with soldering iron. Lift the bulk capacitor away from power board. S14 5 1. Product Material Information Teardown Instruction The following substances, preparation, or components should be disposed of or recovered separately from other WEEE in compliance with Article 4 of EU Council Directive 75/422/EEC. Capacitors / Condensers (containing PCB/PCT) Mercury containing components Batteries Printed circuit boards (with surface greater than 10 square cm) Component contain toner, ink and liquids Plastic containing BFR Component and waste contain asbestos CRT Component contain CFC, HCFC, HGC and HC Gas discharge lamps LCD display > 100 cm2 External electric cable Component contain refractory ceramic fibers Component contains radio-active substances Electrolyte capacitors (height > 25mm, diameter >25mm) Not used Not used Not used Product has printed circuit boards (with surface greater than 10 square cm) Not used Not used Not used Not used Not use Product LCD greater than 100cm2 Product has external cables Not used Not used Product has electrolyte capacitors (height > 25mm) 2. Tools Required List the type and size of the tools that would typically can be used to disassemble the product to a point where components and materials requiring selective treatment can be removed. Tool Description:- - Screwdriver (Philip head with 5 mm & 3 mm) - Screwdriver (Hexagonal to remove VGA connectivity) - Soldering iron - Knife 6Microsoft: Print To PDF; modified using iTextSharp™ 5.5.13.2 ©2000-2020 iText Group NV (AGPL-version)