2E-V285B Computer Case Operation Guide

Introduction

This document serves as the operation guide for the 2E-V285B computer case. It is designed for housing components of a personal computer system. The document is available in multiple languages, including Ukrainian (UA), Russian (RU), and English (EN).

Specifications

Description and Components

Case Description

The computer case is primarily constructed from perforated metal for the front and side panels, and a main chassis. It features a front panel with a circular vent and a perforated mesh front. The rear panel contains expansion slots. The interior is designed to accommodate standard PC components.

Key Parts:

• 1 - Front panel: Perforated metal.
• 2 - Side panel (left/right): Perforated metal.
• 3 - Power Supply Location: Designated area for PSU installation.
• 4 - Rear panel: Features expansion slots.
• 5 - 120mm Fan: A 120mm fan is pre-installed on the rear panel.
• 6 - Front I/O Ports: Includes 1x USB 3.0, 1x USB 2.0, 1x USB Type-C, HD AUDIO+MIC, Power button, and HDD LED indicator.

Note: The appearance and equipment of the item may be supplemented or modified for the purpose of improvement or for improvement of product quality.

Included Components

Installation Guide

Removing Case Panels

To remove the side panel (perforated metal), unscrew the two securing screws (a) and carefully slide the panel off (b).

Motherboard Installation

1. Determine the motherboard's location within the case.
2. Position the motherboard so that its external connectors face the rear of the case.
3. Install the motherboard.
4. Secure the motherboard using the provided fasteners. If the motherboard bracket is not in the correct position, check the contents of the case kit for necessary standoffs.

VGA Installation

1. Identify the expansion slots on the rear of the chassis and remove the necessary PCI bay covers.
2. Insert and secure the graphics card (VGA) into the appropriate expansion slot.

Power Supply Installation

1. The power supply unit (PSU) is located at the top of the chassis.
2. Insert the PSU into its designated bay.
3. Secure the PSU using screws from the rear of the case (a).

HDD/SSD Installation (2.5" bay / 3.5" bay)

2.5" SSD Installation:

• An SSD can be mounted on the side of the top panel as shown in the illustration (a). Note: This mounting method secures the SSD with two screws.

2.5" SSD or 3.5" HDD Installation:

• An SSD or HDD can be installed on the bottom panel at the rear end position, secured by screws from the bottom (b).
• An SSD or HDD can also be installed on the bottom panel at the front end position, secured by screws from the bottom.
• Caution: The bottom panel cannot accommodate two HDDs simultaneously.

Fan Installation

1. A 120mm fan can be installed and secured to the rear panel of the case.
2. The included 120mm fan features a MOLEX power connection.

Operating Conditions and Precautions

General Precautions:

• Ensure all necessary parts are present before assembly.
• Use gloves during assembly to prevent hand injuries.
• Do not use excessive force when fixing components to avoid damaging the case or mounting points.
• Verify that all components are intact and functioning correctly.
• Avoid abrasive or whitening cleaners to prevent scratches and surface damage.
• Store and operate the product out of reach of children and pets.

WARNING: RISK OF ELECTRIC SHOCK!

• PSU installation and replacement must follow manufacturer's instructions and safety warnings. Failure to comply may result in damage or serious injury/death.
• The PSU contains high voltage. Do not open the PSU housing or attempt repairs. It has no user-serviceable components.
• This product is intended for indoor use only.
• Do not use the PSU near water, or in high temperature and humidity.
• Do not install near heat sources (radiators, stoves, etc.).
• Do not insert objects into ventilation openings or grills.
• Do not modify cables or connectors.
• If modular cables are used, only use those supplied by the manufacturer. Incompatible cables can cause damage.
• If any malfunction occurs, contact an authorized service center immediately.
• Failure to comply with instructions voids all warranties.

Storage, Transportation, and Utilization

• Transport the product in its original packaging to prevent damage.
• Store in original packaging in closed, dry, heated rooms at temperatures between +5°C and +40°C, with relative humidity not exceeding 60%. Ensure the air is free from acid or other harmful vapors.
• Transport in individual packaging in closed, dry rooms at temperatures between -40°C and +60°C, with relative humidity not exceeding 60%. Ensure the transport environment is free from harmful vapors.
• If components are pre-installed, check their security or remove them before transportation.
• Avoid moisture or water contact to prevent corrosion.
• Dispose of the case and packaging according to local regulations.
• Do not dispose of with ordinary household waste after its service life; use designated collection points for electrical/electronic equipment.

Warranty Information

This warranty card provides details regarding the warranty service for the 2E computer case. Warranty service is only valid with a correctly filled original warranty card. The product is intended for consumer use; commercial use may void warranty obligations or incur fees. Repairs must be performed by authorized service centers within the specified period. The warranty is voided by misuse, mechanical damage, damage from foreign objects, natural disasters, improper electrical parameters, lack of grounding, tampered seals, or missing serial numbers.

The warranty period is 12 months from the date of sale.

Authorized Service Center:
IP "I-AP-CI"
Address: vul. Marka Vovchka, 18-A, Kyiv, 04073, Ukraine
Tel: 0 800 300 345; (044) 230 34 84; 390 55 12
www.erc.ua/service