Instructions for helpdesk models including: 2 Drawer Filing Cabinet
Assembly Instructions - Please keep for future reference Width - 47.2cm 2 Drawer Filing Cabinet Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123 Please turn to back page for important information when contacting Customer Helpline.
Assembly Instructions - Please keep for future reference Width - 47.2cm 2 Drawer Filing Cabinet Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
File Info : application/pdf, 13 Pages, 4.14MB
DocumentDocument2 Drawer Filing Cabinet Assembly Instructions - Please keep for future reference 023 xx 9433 Dimensions Width - 47.2cm Depth - 38.8cm Height - 56.1cm MADE IN GREAT BRITAIN Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123 Please turn to back page for important information when contacting Customer Helpline. Rev A- 22/05/19 Safety and Care Advice Important - Please read these instructions fully before starting assembly Check you have all the components and tools listed on pages 2 and 3. Remove all fittings from the plastic bags and seperate them into their groups. Keep children and animals away from the work area, small parts could choke if swallowed. Do not stand or put weight on the product, this could cause damage. Assemble the item as close to its final position (in the same room) as possible. We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers. Assemble on a soft level surface to avoid damaging the unit or your floor. Do Not dispose of packaging until assembly complete. Make sure you have enough space to layout the parts before starting. Parts of the assembly will be easier with 2 people. Dispose of all packaging carefully and responsibly when assembly complete. Care and maintenance To protect the furniture, position the furniture out of direct sunlight and away from direct heat sources such as radiators and fires. Do not place the furniture in excessively dry and humid conditions. From time to time check that there are no loose screws on this unit. Always lift furniture when moving it (do not drag) otherwise the joints may be damaged. Do not place hot or cold objects on the surface, always use protective mats to avoid marking the furniture. This product should not be discarded with household waste. Take to your local authority waste disposal centre. Clean spills up immediately Dust surfaces with a soft, dry, lint free cloth. More stubborn marks can be removed using a damp (not wet) cloth. Wipe the surface dry immediately using a soft lint free cloth. Do not use detergents, abrasive cleaning products or cleaning products that contain ammonia, solvents or silicone as these may damage the surface finish. 1 Components - Panels Please check you have all the panels listed below Important - Thick lines indicate finished edges 1390 Top (47.2x38.8cm) 1394 Plinth (43.8x6.0cm) 622xx7002 Left drawer side (30.0x10.0cm) 623xx7002 Right drawer side (30.0x10.0cm) 1391 Left End Panel (54.6x35.5m) 1392 Right End Panel (54.6x35.5 cm) 624xx7008 Drawer back (39.0x10.0cm) 1397 Backpanel (48.7x44.8cm) 1396 Drawer Front (46.4x15.7cm) 1395 Drawer Front (46.4x32.0cm) 624xx7009 Drawer back (39.0x25.0cm) 1393 Bottom (43.8x35.5cm) 8079 Drawer Bottom (40.1x29.8cm) 7622 Drawer Bottom (40.1x32.6cm) 622xx7004 Left drawer side (33.0x25.0cm) 623xx7004 Right drawer side (33.0x25.0cm) 2 Components - Fittings If you have damaged or missing components, call the Customer Helpline: 01709 534123 Please turn to back page for important information when contacting Customer Helpline. Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly, In some case more fittings may be supplied than are required. A Large cam x 8 B Metal dowel x 14 C Small cam x 6 Code 760001103 Code 760003004 Code 760003005 D Panel pin x 5 E 8mm screw x 8 F Panel pin guide x 1 Code 760001012 Code 700003510 Code 684004501 G 18mm bolt x 4 H Panel Holder x 3 I Handle x 2 Code 700002021 Code 680003505 Code 643003506 L1 Left Bracket x 2 L2 Code 760xx7000 R2 Right Runner x 2 N Code 760xx7002 Left Runner x 2 R1 Code 760xx7000 12mm screw x 16 O Code 690001008 Right Bracket x 2 Code 760xx7000 Wooden dowel x 4 Code 770001006 P Filing Trim x 2 Code 680071872 Tools required Cross headed screwdriver (medium & large ) Small Hammer Tape Measure Eye protection (when using a hammer) Ruler - Use this ruler to help correctly identify the screws 0 mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 3 Exploded View 1391 1390 1397 1393 1392 622xx7002 1396 624xx7008 1394 8079 623xx7002 622xx7004 624xx7009 1395 7622 623xx7004 4 Assembly Instructions Step 1 B x4 Fitting dowels to top panel. B B Insert 4 metal dowels B into the top panel 1390 B Note: Tighten metal dowels up fully against the panel. B 1390 B Do not over-tighten. Step 2 O x4 Fitting wooden dowels to the plinth panels. O O Insert 4 wooden dowels O into the plinth panel 1394 Step 3 A x4 Fitting cams and dowels to the end panels. a: Insert 2 metal cams A A and 2 metal dowels B into left end panel 1391 . b: Insert 2 metal cams A and 2 metal dowels B into right end panel 1392 . 1394 B x4 B B O O 1391 A A A A A B B 1392 B 5 Assembly Instructions Step 4 L1 E N x2 x4 x2 Attaching the left bracket to the left end. Using 2 screws E , secure the bracket L1 to the left end panel 1391 as shown in diagram 1. Use 1 screw N to secure the front of the bracket. E E E 1391 E Repeat on all brackets. Step 5 R1 x2 Attaching the right bracket to the right end. Using 2 screws E , secure the bracket R1 to the right end panel 1392 as shown in diagram 1. E Use 1 screw N to secure the front of the bracket. Repeat on all brackets. E N x4 x2 E E 1392 E Diagram 1 E Corresponding Hole E L1 1ST Diagram 2 N L1 Diagram 1 E 2ND E R1 1ST Diagram 2 N R1 Step 6 A Inserting cams into the x4 bottom panel. Insert 4 cams A into the bottom panel 1393 . A A 1393 A A 6 Assembly Instructions Step 7 B G I Drawer assembly x2 x4 x2 N C x12 x6 B a: R2 L2 x2 x2 B a: Insert dowels into drawer front . 1396 Note: Insert metal dowels B as far as shown by arrows. Repeat on 1395 Do not over tighten. B 1396 C b: Insert small camsC into left 622xx7002 and right 623xx7002 drawer sides. Note: Ensure cam arrow points towards the edge with hole. b: Left hand side 622xx7002 Right hand side 623xx7002 C C c: Insert wooden dowels in drawer back 624xx7008 into holes in c: Left hand side left 622xx7002 right 623xx7002 hand 622xx7002 drawer sides. Repeat the following steps on drawer sections, 622xx7004 623xx7004 and 624xx7009 Continued on next page. 7 Drawer Back 624xx7008 Right hand side 623xx7002 Assembly Instructions Step 7 - Continued Drawer assembly d: Continued... d: Slide drawer bottom 8079 into grooves in left,right drawer sides and drawer back. Ensure foil on the drawer bottom is facing upwards. e: Insert cams C already inserted in left and right e: drawer sides onto dowels B in drawer front 1396. 8079 FOIL FACE C Turn cam 180 degrees to lock f: Secure handle I to drawer front 1396 using bolts G f: Turn Drawer upside down. g: Using 12 screws N g: secure the left runner L2 and the right runner R2 to the drawer box. Ensure that the wheel on the runners is to the back of the drawer box. Repeat steps with other drawer. 1396 G G 1396 I N R2 L2 N N L2 8 Assembly Instructions Step 8 Connect left end to the bottom and plinth panel Connect the dowels in the left end 1391 to the cams in the bottom panel 1393 and the wooden dowels in the plinth panel 1394 . Turn cams 180 degrees to lock. 1391 1393 1394 Step 9 Connect right end to the bottom and plinth panel Connect the dowels in the right end 1392 to the cams in the bottom panel 1393 and the wooden dowels in the plinth 1394 . 1392 Ensure plinth sits Ensure plinth is flush. not overhanging. 1393 Step 10 Connect the top panel. Connect the dowels in the top panel 1390 to the left end 1391 and right end 1392 . 1390 1394 1391 1392 9 Assembly Instructions Step 11 Slide back panel into grooves and Squaring up the unit. Slide the back panel into the grooves in the end panels and top panel. YY XX DIAG 1 XX YY IMPORTANT! Ensure a tape measure is used to square unit up. Before securing the back YY it is necessary to square up the unit. You can do this by measuring between XX - XX and YY - YY ensuring these are the same (DIAG 1). If they are not (DIAG 2) Apply slight pressure as indicated (DIAG 3) until they are the same. YY XX DIAG 2 YY XX DIAG 3 XX YY XX YY XX YY XX Measure to external corners Step 12 D Secure back panel x4 Use the panel pin guide when locating the panel pins. This will hold the panel pins vertical and ensure the correct distance from the edge. F x1 1397 1393 D F 10 Assembly Instructions Step 13 H x3 Add stability blocks. Slide the thin point of the stability blocks H H H H between the back panel 1397 and the grooves. 1397 Once inserted fully, H tighten the screws in the stability blocks. IMPORTANT! Please ensure that the stability blocks are used correctly to secure the back panel in place. Step 14 P x2 Fit the drawers and filing trims. Stand the unit up. Tilt the drawers as shown and slide onto the runner brackets. Place the filing trims P onto drawer sections 622xx7004 and 623xx7004 . P 622xx7004 P 623xx7004 11 ACsosnegmrabtluylaIntisotnrus!ctYionusr unit is complete. Important Information If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123 8am - 4.30pm (Monday toThursday) 8am - 2.30pm (Fridays) (by contacting the customer service line your statutory rights are not affected) Please have the following information to hand: >> Unit Description >> Product Code >> Product Colour >> Place of Purchase >> Catalogue Ref. No. >> Item Code >> Assembly Instructions We do have an answer machine should you contact us out of office hours, so in addition to the above information could you leave your name, address, daytime telephone number and the nature of your call on the answerphone. All calls will be actioned asap. You can also e-mail your requests to us at: customer.helpdesk@addspacefl.co.uk Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited, Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY.