ASUS ROG PELTA Wireless Gaming Headset Quick Start Guide

Getting Started

To set up your ROG PELTA gaming headset:

1. Connect the headset to your device through Bluetooth® or the dongle.
2. Download the Armoury Crate software from http://rog.asus.com and then install it on your computer.

Pairing Bluetooth® Again

You can pair Bluetooth® again by following the steps below:

1. Turn off your headset.
2. Press and hold the Function button for 5 seconds.

Headset Features

• Microphone Mute button
• Audio control wheel
• Function button
• Mode switch
• Microphone jack

Buttons and Switches

• Mode switch: RF 2.4GHz mode, Bluetooth® mode, Power off (USB mode)
• Microphone Mute button
• Function button
• Audio control wheel
• Turn on/off RGB lighting

LED Indicators

• Microphone LED: Solid (red) - Microphone muted; No light - Microphone unmuted
• Logo LED indicator: Flashing (red) - Headset charging; Fast flashing (red) - Low battery (below 20%); Solid (green) - Fully charged; Flashing (blue) - No Bluetooth device paired; Fast flashing (blue) - Pairing to a device; No light - Headset off

Installing the Elastic Headband

Diagram shows how to attach the elastic headband to the headset.

Notices

Safety Guidelines

Operating temperature: 0°C ~ 40°C, with an operating voltage of 3.3V ~ 4.2V.

Limitation of Liability: ASUS is liable for damages up to the contract price of each product for bodily injury, damage to real property, or tangible personal property, or other actual damages resulting from ASUS's failure to perform its legal duties. ASUS is not liable for third-party claims, loss of data, or special, incidental, or indirect damages, including lost profits.

Proper disposal: Do not throw the device in municipal waste. Recycle electronic products according to local regulations. Do not throw the device in fire, short circuit contacts, or disassemble it.

Prevention of Hearing Loss: Do not listen at high volume levels for long periods to prevent possible hearing damage.

Lithium-Metal Battery Warning: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to manufacturer’s instructions.

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

CE Mark Warning

This device complies with the essential requirements and other relevant provisions of related EU Directives.

VCCI: Japan Compliance Statement

VCCI Class B Statement. This device is intended for use in a home environment, but may cause interference to radio or television reception if placed too close to these devices. Follow the instructions in the manual for correct operation.

KC: Korea Warning Statement

This table indicates the presence of hazardous substances in the product's components. 'X' indicates that the hazardous substance exceeds the limit requirement, while 'O' indicates that the hazardous substance is below the limit requirement.

Compliance Statement of Innovation, Science and Economic Development Canada (ISED)

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation.

Radio Frequency (RF) Exposure Information

The radiated output power of the Wireless Device is below the Innovation, Science and Economic Development Canada (ISED) radio frequency exposure limits. The Wireless Device should be used in such a manner that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the ISED RF Exposure limits under portable exposure conditions.

France sorting and recycling information

For collection points, visit www.quefairedemesdechets.fr. Prioritize repair or donation of your device.

Regional notice for Singapore

This ASUS product complies with IMDA Standards.

Manufacturer Information

Manufacturer: ASUSTek COMPUTER INC.

Address: 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112

Authorized Representative in Europe: ASUS COMPUTER GmbH

Address: Harkortstrasse 21-23, 40880 Ratingen, Germany

Authorized Representative in United Kingdom: ASUSTeK (UK) LIMITED

Address: 1st Floor, Sackville House, 143-149 Fenchurch Street, London, EC3M 6BL, England

Service and Support

Visit our multi-language website at https://www.asus.com/support.