Victrola Music Center

Unpack Your Music Center

Locate the following items:

• (1) Music center
• (2) Feet (x4)
• (3) Power adapter
• (4) Clock battery (AA)
• (5) Legs (x4) - *Included with the Century Signature+ (VTA-835SB) or sold separately.*

Prepare Music Center

Installing Feet / Legs

1. Carefully turn the music center upside down while holding the lid closed.
2. Insert feet/legs into the 4 corner brackets. Rotate clockwise until tightened.
3. Carefully turn the music center right side up while holding the lid closed.

Opening and Closing the Lid

• OPEN: Raise the lid to the fully open position. Lightly pull the hinge forward and gently lower the lid until the hinge is latched.
• CLOSE: Raise the lid slightly and lightly push the center of the hinge to unlatch. Gently lower lid.

Place Music Center on a Flat and Level Surface

1. Remove all packaging materials.
2. Plug in the power adapter.
3. Remove the tonearm twist tie.
4. Remove tape and clear the stylus cover.

Prepare Clock

1. Locate the clock battery compartment behind the clock face.
2. Open the compartment and install the single AA battery.
3. Close the clock battery compartment.
4. Adjust clock time by rotating the dial.

Getting Started

Multi-Function Knob

• Press and hold to power ON / OFF.
• Single press to switch modes: VINYL, VINYLSTREAM™ (BLUETOOTH OUTPUT), BLUETOOTH (INPUT), COMPACT DISC, CASSETTE, AUX.
• Rotate knob to adjust volume.

Playing a Record

Vinyl Mode - Internal Speakers / RCA / Headphones

Enter VINYL mode. The volume of the internal speakers is controlled by rotating the multi-function knob. For RCA / Headphone output information, see section 9.

Vinylstream Mode - Pair Bluetooth Speaker or Headphones

1. Enter VINYLSTREAM (Bluetooth output) mode. The music center will automatically enter pairing mode. LED: Flashes white.
2. Ensure your Bluetooth device is in pairing mode.
3. The music center will automatically pair to your Bluetooth device.
4. Once paired, the LED will turn solid white.

Note: Volume is controlled by the Bluetooth device.

Basic Operation

1. Unlatch the tonearm.
2. Raise the tonearm using the lift lever.
3. Use the finger lift to align the stylus over the record.
4. Lower the tonearm using the lift lever to begin playing.

Note: At the end of the record, the music center will automatically stop spinning. Use the lift lever to return the tonearm to the resting position.

Adjusting Record Speed

Use the speed switch next to the tonearm to adjust the record speed between 33 1/3 RPM (default), 45 RPM, and 78 RPM.

Playing a 7" Record

1. Locate the 45 RPM adapter.
2. Place the adapter over the center spindle.
3. Select the correct speed.
4. Place the record over the adapter and begin playback.

Bluetooth Mode

Bluetooth Mode - Pair Bluetooth Device

1. Enter BLUETOOTH mode. The music center will automatically enter pairing mode. LED: Flashes white.
2. On your device, turn on Bluetooth and select "Victrola Century Signature" in the available device list.
3. Once paired, the LED will turn solid white.

Note: Most devices support the use of the music center's play/pause, previous, and next buttons.

Playing a CD

Basic Operation

1. Enter COMPACT DISC mode.
2. Press the open/close button to open the CD tray. Insert a CD into the tray and press open/close to close. Playback will automatically begin.
3. Press the play/pause button to start and stop the CD.
4. Use the previous and next buttons to change tracks. Press and hold the previous and next buttons to rewind and fast forward.

Repeat / Shuffle

Press the repeat button to cycle through different CD modes: REP 1 (Repeats a single track), REP ALL (Repeats entire CD), RAN (Shuffles CD tracks).

Playing a Cassette

Basic Operation

1. Enter CASSETTE mode.
2. Insert cassette; playback will automatically begin.

Cassette Button

• Press halfway down to fast forward. Press again lightly to resume playback.
• Press down all the way to end playback and eject tape.

Note: To rewind a side, eject and flip the tape to the other side and fast forward.

Playing an External Device (AUX)

Basic Operation

1. Enter AUX mode.
2. Connect an external device to the 3.5 mm aux jack on the front of the music center and begin playback on the external device.

Note: Most devices support the use of the music center's play/pause, previous, and next buttons.

RCA & Headphone Output

RCA Output

1. Connect the music center to external speakers using an RCA cable (not included). RED PLUG - Insert into the RED (RIGHT) JACK. WHITE PLUG - Insert into the WHITE (LEFT) JACK.
2. Lower the volume of the internal speakers and control volume from the external speakers.

Headphone Output

Use the phones jack on the front of the music center to connect headphones/earbuds. Lower the volume before connecting headphones and increase as needed.

Replacing the Stylus

Removing the Stylus from the Tonearm

1. Place your fingers at the tip of the stylus and push down in direction "A". WARNING: Applying too much force may damage or break the cartridge.
2. Pull the stylus out in direction "B".

Installing the Stylus (Replacement Stylus # ITNP-LC1)

1. Hold the tip of the stylus and insert the other edge by pressing toward direction "C".
2. Push the stylus up toward direction "D" until it locks at the tip.

Caution:

• Do not bend or force the stylus into the cartridge.
• Do not touch the stylus needle to avoid injury.
• Turn off the unit's power before replacing the stylus.
• Keep out of reach of children.

Note: The stylus should last about 300 hours under normal use. Replace the stylus as soon as you notice a change in sound quality. Playing 78 RPM records may accelerate stylus wear.

Adjusting LED Illumination

1. Press and hold the repeat button for 3 seconds to enter illumination adjustment mode.
2. Single press the repeat button to cycle through illumination modes: HI (default), LO, OFF.
3. The setting will save automatically after 3 seconds.

Factory Reset

Enter BLUETOOTH mode, press and hold the open/close button for 5 seconds. All source mode LEDs will flash 3 times when the factory reset is complete. This removes all paired Bluetooth devices and resets LED illumination to the factory default.

Specifications

General

DIMENSIONS (MAIN UNIT): [Dimensions not specified in text]

Safety Warnings

Please read safety instructions and respect the following warnings before operating the appliance:

• TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
• TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
• Always follow basic safety precautions, especially when children are present.
• Children should be supervised to ensure they do not play with the appliance.
• Do not damage the power cord; do not place heavy objects on it, stretch or bend it. Do not attach extension cables. Damage to the power cord may cause fire or electric shock.
• If the supply cord is damaged, it must be replaced by the manufacturer, a service agent, or similarly qualified persons to avoid a hazard.
• Ensure the unit is plugged into an AC 100-240V 50/60Hz power outlet. Using higher voltage may cause malfunction or fire.
• If the power plug does not fit your outlet, do not force it.
• Turn off the unit before unplugging it from the power source.
• Do not disconnect or connect the power cord with wet hands.
• Ensure the main plug is always easily accessible.
• This product contains no user-serviceable parts. Refer servicing to qualified professionals. Unauthorized repairs may void the warranty.
• Ensure this product is used in moderate climates only.
• Place the product on a flat, stable surface not subject to vibrations.
• Ensure the product and its parts do not overhang the edge of the supporting furniture.
• To reduce the risk of fire, electric shock, or product damage, do not expose it to direct sunlight, dust, rain, or moisture. Do not expose to dripping or splashing, and do not place objects filled with liquids on or near the product.
• Do not place objects filled with liquids, such as vases, on the apparatus.
• Do not install near heat sources like radiators, stoves, or other heat-producing apparatus.
• Do not place the product in areas with high humidity and poor ventilation.
• Do not mount this product on a wall or ceiling.
• Do not place the unit near TVs, speakers, or other objects that generate strong magnetic fields.
• Do not leave the unit unattended when in use.
• Allow at least 30 cm clearance from the rear and top, and 5 cm from each side. Ensure ventilation openings are not covered.
• NEVER let anyone, especially children, push anything into holes, slots, or openings in the unit's casing, as this could result in a fatal electric shock.
• Storms are dangerous for electric appliances. Disconnect all cables and connectors before a storm.
• Excessive sound pressure from headphones can cause hearing loss.
• Do not cover ventilation openings; this unit is not intended for use on soft surfaces.
• WARNING: Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to laser beam. This product is a Class 1 laser device. Laser beams can cause eye injury. Do not attempt to disassemble the device. Refer all maintenance and repair to the manufacturer or customer service.
• CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

Maintenance

• Unplug the power cable before cleaning.
• Use a soft, clean rag to clean the exterior. Never use chemicals or detergents.

Power Adapter

• To disconnect from the main supply, unplug the lead from the main socket.
• Only use the supplied main adapter.
• The socket-outlet shall be installed near the equipment and shall be easily accessible.
• Symbols indicate: AC Voltage, DC Voltage, Class II equipment, For indoor use only, Energy Efficiency marking (Level VI), Polarity of D.C. power connector.
• Users are requested to use existing return facilities for used equipment and batteries.

FCC & IC Warnings

FCC Statements

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules and Innovation, Science and Economic Development Canada's license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

French Translation: Le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de license. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Note

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference. However, there is no guarantee that interference will not occur in a particular installation. If interference occurs, try to correct it by:

• Reorienting or relocating the receiving antenna.
• Increasing the separation between the equipment and receiver.
• Connecting the equipment to an outlet on a different circuit than the receiver.
• Consulting the dealer or an experienced radio/TV technician.

FCC & IC Radiation Exposure Statement

This equipment complies with FCC and Canada radiation exposure limits for an uncontrolled environment. This device complies with RSS247 of Industry Canada. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

French Translation: Cet équipement est conforme aux limites d'exposition aux radiations définies par le Canada pour des environnements non contrôlés. Cet appareil se conforme à RSS247 de Canada d'Industrie. Cet équipement doit être installé et utilisé à une distance minimum de 20 cm entre l'antenne et votre corps. Cet émetteur ne doit pas être installé au même endroit ni utilisé avec une autre antenne ou un autre émetteur.

Limited Warranty

Victrola is a registered trademark of Innovative Technology Electronics, LLC.

United States

For detailed information about the warranty policy and limitations, visit victrola.com/pages/warranty.

Outside the U.S., Canada, and US Territories

The warranty on this product complies with applicable law when sold to a consumer outside these regions. To obtain warranty service, contact the dealer or distributor with your original receipt.

Canada and US Territories

The warranty on this product complies with applicable law when sold to a consumer in Canada or a US Territory. To obtain warranty service, contact the dealer or distributor with your original receipt.

If assistance from the dealer is not possible, contact customer service for warranty assistance at victrola.com/contact.

Customer Support

Visit VICTROLA.COM/PAGES/CUSTOMER-CARE

Email: support@victrola.com

Phone: (877)483-2497