Linkind Wi-Fi CCT Smart Filament LED Bulb Operation Manual

Brand: Linkind

Function Introduction

[App Control]: Control the bulb via the AiDot mobile application.
[Voice Control]: Control the bulb using voice commands with compatible assistants.
[Brightness and Color Temperature Control]: Adjust the brightness and color temperature of the bulb.
[Timer and Countdown]: Set timers and countdowns for the bulb's operation.

Installation Instructions

After installing the bulb, power it on.
The bulb will gradually blink twice under warm white light, indicating it has entered the network distribution state.
To connect the bulb to the internet, download the AiDot APP and follow the in-app guidelines.

Quick Start Guide

Download the "AiDot" application by searching in the App Store or Google Play.
Create an account and sign in. Tap the '+' icon to add the "Wi-Fi Light Bulb".
Follow the on-screen instructions within the app. (Note: Ensure Bluetooth and location services are enabled on your device.)

Troubleshooting

Cannot connect the bulb to AiDot App

Verify the bulb is powered on.
Ensure your smartphone's Wi-Fi is enabled and connected to a 2.4GHz network (5GHz is not supported).
Confirm that Bluetooth and GPS are turned on.
Position your smartphone close to the bulb during the initial network configuration.
Double-check that the correct Wi-Fi password was entered. Ensure the distance between the bulb and router is less than 50 feet.
Confirm your home network is stable. If not, try connecting to another phone's hotspot.

Can I use group control with voice assistance?

Ensure your bulb is connected to Wi-Fi before using voice assistance.
Configure voice group control within the Alexa, Google Assistant, or SmartThings app.

What is the maximum number of bulbs I can connect via Bluetooth?

Typically, up to 6 bulbs can be connected via Bluetooth, though the exact number may vary depending on your smartphone brand.

How many bulbs can be connected to one phone?

Up to 50 bulbs can be connected to a single phone, provided the network connection is stable.

How to reset the smart bulbs?

Turn the bulb on and off consecutively 6 times, maintaining an interval of 0.5 to 1.5 seconds between each cycle. The bulb will blink twice upon successful reset.

What should I do if the bulb is offline?

Check if the Wi-Fi SSID or password has been changed. If so, reset the device and re-add it to the AiDot APP with the new credentials. If not changed, try restarting the device.
Assess the strength of the Wi-Fi connection. If the signal is weak, move the router closer to the device or vice versa. Consider reducing the number of connected devices on your router to lessen Wi-Fi load.
Ensure the device's voltage supply is stable, as fluctuations can cause reboots and connection issues.
Check if the router or device has been powered off for an extended period. If so, re-power it. If it was off for a long time, reset the device and re-add it to the AiDot APP.

Frequently Asked Questions

Can Linkind Smart Bulbs connect to wall dimmers?

No, Linkind Smart Bulbs cannot be connected to wall dimmers or other variable power devices. Dimming functionality is exclusively managed through the AiDot App or other compatible smart devices.

How to Connect Alexa, Google Home or SmartThings?

Linkind bulbs are not directly discoverable by Alexa. First, connect the bulbs to the AiDot app. Then, integrate the AiDot app with your Alexa app by enabling the "AiDot" skill. After linking accounts, use your voice assistant with the device names assigned in the AiDot app to control the lights (e.g., turn on/off, change colors, dim). Google Home and SmartThings integration follows similar steps.

How to reset the smart bulbs?

Turn the bulb on and off consecutively 6 times, with an interval of 0.5s-1.5s between each action. The bulb will blink twice, confirming a successful reset. After resetting, the device will still appear in the app.

What should I do if the bulb is offline?

Verify if your Wi-Fi SSID or password has changed. If it has, reset the bulb and re-add it to the AiDot APP using the new credentials. If the credentials haven't changed, try restarting the bulb. Check the Wi-Fi signal strength; if it's weak, reposition the router or the bulb. You might also consider reducing the load on your Wi-Fi network by disconnecting less-used devices. Ensure the power supply voltage is stable, as inconsistent voltage can cause the bulb to reboot. Finally, check if the device or router has been powered off for a prolonged period; if so, re-power it, or reset and re-add the device if it was off for a long time.

How to get support?

Email: service@linkind.com
Support Phone: 1-877-770-5727 (Monday-Friday, 9:00 AM - 5:00 PM PST)
Website: http://www.linkind.com
Social Media: @linkind.lights, @linkindofficial

Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC's RF Exposure guidelines, this equipment should be installed and operated with a minimum 20cm distance between the radiator and your body. Use only the supplied antenna.

Cautions

Risk of electrical shock. Disconnect power at the fuse or circuit breaker before installing or servicing.
To prevent early lamp failure, the lamp should only be installed in operating environments ranging between -20°C and +40°C (-4°F and +104°F).
Suitable for damp locations.
Not for use with dimmers.
Lamp dims via wireless control and will not operate with a dimmer switch.
Not for use in totally enclosed luminaires.
Not for use in emergency light fixtures or exit signs.
Ensure the fixture can support the added weight of the lamp/bulb.

Contact Us

SPRING SUNSHINE TECHNOLOGY CO., LIMITED
FLAT/RM 01-04, 24/F, FU FAI COMMERCIAL CENTRE,
27 HILLIER STREET, SHEUNG WAN, HK

Manufacturer: Leedarson loT Technology Inc.
Address: No.1511, 2nd Fanghu North Rd, Huli District, Xiamen, China

Phone: 1-877-770-5727 (Monday-Friday 9:00 AM - 5:00 PM PST)

Email: service@linkind.com

Website: http://www.linkind.com

Social Media: @linkind.lights, @linkindofficial