Acer LCD Monitor Quick Start Guide (QSG)
Important Safety Instructions
Please read the following instructions carefully.
- To clean the LCD monitor screen:
- Turn off the LCD monitor and unplug the power cord.
- Spray a non-solvent cleaning solution onto a rag and clean the screen gently.
- Do not place the LCD monitor near a window. Exposing the monitor to rain, moisture, or sunlight can severely damage it.
- Do not apply pressure to the LCD screen. Excessive pressure may cause permanent damage to the display.
- Do not remove the cover or attempt to service this unit yourself. An authorized technician should perform servicing of any nature.
- Store the LCD monitor in a room with a temperature of -20° C to 60° C (-4° F to 140° F). Storing the LCD monitor outside this range may result in permanent damage.
- Immediately unplug your monitor and call an authorized technician if any of the following circumstances occur:
- Monitor-to-PC signal cable is frayed or damaged.
- Liquid spills onto the LCD monitor or the monitor is exposed to rain.
- The LCD monitor or case is damaged.
Attaching the Monitor to the Base
- Remove the monitor from the packaging.
- Attach the footstand to the base (for selected models).
- Turn clockwise to lock. Ensure the base is locked onto the stand (for selected models).
- Secure the base to the stand by turning the screw using the integrated tab or a suitable coin (for selected models).
Connecting Your Monitor to a Computer
Diagram Description: The diagram shows the rear ports of the monitor and a computer's graphics card. It illustrates connecting the monitor to the computer using signal cables (DP/HDMI) and the power cable.
- Turn off your computer and unplug its power cord.
- Connect the signal cable (e.g., DisplayPort or HDMI) to the corresponding input socket on the monitor and the output socket on your computer's graphics card. Tighten the thumbscrews on the signal cable connector.
- Insert the monitor power cable into the power port at the back of the monitor.
- Plug the power cords of your computer and your monitor into a nearby electrical outlet.
Note: Audio output is only available on audio output models. Please refer to the user manual for more instructions.
AdaptiveSync (DP/HDMI)
AdaptiveSync allows a supported graphics source to dynamically adjust the display's refresh rate based on typical content frame rates. This provides power efficiency, virtually stutter-free visuals, and low-latency display updates.
Visual Description: The document lists adjustment levels for AdaptiveSync, represented by numbers 1 through 5.
External Controls
Diagram Description: The diagram shows the location of the monitor's control buttons on the rear panel.
Control | Function |
---|---|
1. Power button | Turns the monitor on/off. Blue light indicates power on. Amber light indicates standby/power saving mode. |
2. Function key | a. Press to view the Main OSD page. Press again to enter hotkey1 function. b. When the Function Menu is active, press this key to view basic monitor information, current input, or reset custom color settings to factory defaults. |
3. Function key | a. Press to view the Main OSD page. Press again to enter hotkey2 function. b. When the Function Menu is active, press this button to select scenario mode or game mode. |
4. Function key | a. Press to view the Main OSD page. Press again to enter the Input select function. b. When the Function Menu is active, this button exits the OSD. |
5. Function key | a. Press to view the Main OSD page. Press again to enter the next function in the Function Menu. b. The single toggle button on the back of the display bezel operates like a joystick. Toggle the button in four directions to move the cursor. Press the button to select the desired option. A bright gray indicator signifies operability; dark gray signifies inoperability. |
Regulations and Safety Notices
FCC Notices
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the device and receiver.
- Connect the device into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/television technician for help.
CE Declaration of Conformity
Acer Inc. declares that this LCD monitor complies with the essential requirements and other relevant provisions of EMC Directive 2014/30/EU, Low Voltage Directive 2014/35/EU, RoHS Directive 2011/65/EU, and Directive 2009/125/EC regarding ecodesign requirements for energy-related products.
Notice: Shielded Cables
All connections to other computing devices must be made using shielded cables to maintain compliance with EMC regulations.
Notice: Peripheral Devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to comply with Class B limits may be attached to this equipment. Operation with non-certified peripherals may result in interference to radio and TV reception.
Caution
Changes or modifications not expressly approved by the manufacturer could void the user's authority, granted by the Federal Communications Commission, to operate this product. To prevent damage to the monitor, do not lift the monitor by its base.
Operation Conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Notice: Canadian Users
Complies with CAN ICES-003(B)/NMB-003(B).
Disposal of Waste Equipment by User in Private Household in the European Union
Symbol Description: A symbol on the product or packaging indicates that this product must not be disposed of with other household waste. It is the user's responsibility to dispose of waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. This process helps conserve natural resources and ensures recycling that protects human health and the environment. For more information, contact your local city office, household waste disposal service, or the shop where the product was purchased.
Acer monitors are intended for video and visual display of information obtained from electronic devices.