Momentum Transend E+ Fender Set

Specifications

• Material: plastic/aluminum
• Color: Matt black
• Diameter: Front: 678mm / Rear: 900mm
• Weight: Front: 247g / Rear: 355g

Package Contents

• 1 x front fender
• 1 x rear fender
• 1 x U stay for front fender
• 2 x V stays for rear fender

Front Fender Hardware:

• (F-a) 1 x M5*10 bolt
• (F-b) 2 x M5*12 bolts
• (F-c) 3 x M5 washers
• (F-d) 2 x M5*8 bolts
• (F-e) 1 x M5 clip set

Rear Fender Hardware:

• (R-a) 1 x M6*30 bolt
• (R-b) 1 x M6 washer
• (R-c) 1 x M6 spring washer
• (R-d) 1 x curved washer
• (R-e) 1 x M6 nut
• (R-f) 2 x M5*12 bolts
• (R-g) 2 x M5 washers

Installation Guide

Warning

• Read all information in this manual carefully before using the fender set. Safety instructions are important and should not be overlooked.
• Only use the fender set and supplied installation hardware.
• Do not modify the fender set.
• Periodically check all bolts for tightness due to vibrations.
• Do not use the fender set to move or lift the bike.
• If unsure about compatibility or installation, consult your local authorized dealer.
• Regulations vary by country/location; always check in advance.

Installation Steps

1. Ensure the bike is switched off, kickstand engaged, and on level ground.
2. Remove accessories that might interfere with installation or use.
3. Front fender: Assemble the front fender and U stay using two M5*8 bolts and one M5 clip set with a Phillips screwdriver. Ensure the end of the U stay angles upward. Do not tighten completely yet.
4. Install the front fender onto the bike. At the top of the front fork, use a 3mm hex torque wrench to tighten one M5*10 bolt and an M5 washer on the back side of the front fork. Do not tighten completely yet.
5. On both sides of the front fork, use a 4mm hex torque wrench to tighten two M5*12 bolts and M5 washers with 5-8Nm torque.
6. Adjust the front fender to the appropriate height and tighten the bolts with 5-8Nm torque.
7. Rear fender: Assemble the two V stays with the rear fender using a Phillips screwdriver. Use the shorter leg of the V stay as the front (marked "F"). Do not tighten completely yet.
8. Install the rear fender onto the bike. For the front end of the seat stay, use a 5mm hex torque wrench and a 10mm open spanner to tighten one M6*30 bolt and an M6 washer on the upper side, and one M6 spring washer, curved washer, and M6 nut on the lower side.
9. For the rear end of the seat stay, use a 4mm hex torque wrench to tighten two M5*12 bolts and M5 washers.
10. Adjust the rear fender to the appropriate height and tighten the bolts with 5-8Nm torque.
11. If assembling a Momentum rack, purchase an additional Dual Mounting Kit.
12. Double-check that the fender set is properly installed and does not move or rotate.

Diagram Description: The installation guide includes diagrams illustrating the front and rear fender components and their attachment points on a bicycle. The front fender attaches to the fork crown and fork legs. The rear fender attaches to the seat stays and chainstays. Hardware is labeled with corresponding part numbers (F-a to F-e for front, R-a to R-g for rear).

Usage Information

• Check that the fender set is firmly mounted before every ride.
• Regularly check the fender set and mounting parts for any signs of looseness, deterioration, corrosion, or other damage.

Limited Product Warranty Information

Giant Global Inc. warrants its products for one (1) year from the date of purchase to the original owner. This applies to products purchased new from an Authorized Giant Dealer and assembled by that dealer.

Limited Remedy

The sole remedy for warranty claims is the replacement of defective parts with those of equal or greater value, at Giant Global Inc.'s discretion. This warranty applies to the original owner and is not transferable. Giant Global Inc. is not liable for direct, incidental, or consequential damages, including those for personal injury, property damage, or economic losses, regardless of contract, warranty, negligence, product liability, or other theory.

Exclusions

• Normal wear and tear.
• Products serviced by unauthorized dealers.
• Modifications from the original condition.
• Use for abnormal, competition, or commercial activities, or purposes other than intended.
• Damage from failing to follow the User's Manual.
• Paint, finish, and decal damage from competitions, jumping, downhill, or training, or from severe conditions/climates.
• Labor charges for part replacement or changeover.

Giant Global Inc. and its employees/agents are not liable for any loss or damage arising from any Giant Global Inc. product, including incidental or consequential loss due to negligence or default. Giant Global Inc. makes no other warranties, express or implied. Implied warranties are limited to the duration of the express warranties. Claims must be made through an Authorized Giant Dealer or distributor with proof of purchase. Claims made outside the country of purchase may incur fees and restrictions. Warranty details may vary by country. This warranty grants specific legal rights and may not affect statutory rights.

Disclaimer

For safety, quality, and reliability, use only original parts or Giant authorized replacements. Giant is not responsible for direct, incidental, or consequential damages, including personal injury, property damage, or economic losses due to improper use.