iDatalink - Home
Installation Guide for FIRSTECH models including: FTI-NSP2-NI3-Nissan Frontier Intelli-Key PTS AT_20-24_ENX, NSP2-NI3 Frontier Intelli Key PTS AT, NSP2-NI3, Frontier Intelli Key PTS AT, Intelli Key PTS AT, Key PTS AT, PTS AT, AT
FTI-NSP2 | MyFirstech Install
File Info : application/pdf, 4 Pages, 285.69KB
DocumentDocumentFTI-NSP2: Vehicle Coverage and Preparation Notes Make Model Year Install CAN Lights BCM POC I/O Changes DL-NI3 Nissan Frontier Intelli-Key PTS AT 2020-24 Type 2 Type A Park / Auto POC 1 Hazard1/2 RSC Green White/Blue See note None/IGN Install Type 2 requires BLADE-AL(DL)-NI3 firmware, flash module and update the controller firmware before installing. CAN: The NSP2 harness, when configured for NI3 applications, does not require a specific configuration of the harness CAN connector, the NI3 CAN connections are hardwired between the white 14-pin connector and the Black 40-pin BCM connector. Lights: Visual status confirmations and diagnostic information are provided via hazard lights when using the NSP2 harness. The controller POC1 output must be configured for one of the following settings (depending on switch type): * Hazard light [ 30 ] momentary hazard switch * Hazard light 2 [ 23 ] latching hazard switch POC Configuration: CM7/CMX: POC2 - 2nd START [ 2 ] POC3 - 2nd IGN [ 3 ] CM9: POC3 - (-) START POC4 - (-) IGNITION I/O Changes: Type 2 requires configuring the CN1 blue wire for IGN output, controller specific settings are listed on the next page. Vehicle Damage Warning: Caution should be taken to avoid mixing up the BCM connectors, vehicle damage will result if the connectors are positioned improperly. It is advised that you make the BCM connections one at a time, confirming that each T-harness connection is at the correct BCM position before proceeding to the next connection, attempting to program, or attempting to remote start. FTI-NSP2: Installation and Configuration Notes A REQUIRED CONNECTIONS - SECURE UNUSED I/O CONNECTORS B REQUIRED CONNECTIONS - SEE WARNING ABOVE C REQUIRED CONNECTION D REQUIRED CONNECTION - REQUIRES JUMPER/SETTING CONFIGURATION E NOT REQUIRED CM7000/7200 Cut loop for A/T CM7X00 IIIIIIIIIIIIIIIIIIIIIIEIIIRIIIIIIIIIIIIIIIIIIIIIIIIIIIII D LAN 2001 O O Z K E R E D st. E IIIIIIIII S ID D KO O rG fo AD E R R E 'T T AN NC CE AND WHO O H W WANNA LEARN TO IIIIIIIII FEATURE COVERAGE CM-900S/900AS CM900AS/900S Jumper IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII D O OTHER STUFF GOOD TOO IMMOBILIZER DATA SECURE TAKEOVER PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM POWER LIFTGATE TRUNK/HATCH RELEASE DOOR STATUS HOOD STATUS TRUNK STATUS BRAKE STATUS TACH OUTPUT E-BRAKE STATUS CM -900 FTI-NSP2 - DL-NI3 - Type 2 2020-24 Nissan Frontier Intelli-Key PTS AT A BLADE PWR/CN1 Lock CM7/CMX CM900AS CM900S 1 2 OBD-II Connector B 1 1 16 *Not required *Optional Hood Siren Horn C NI3 BCM 2 5 1 4 2 3 B See Vehicle Damage Warning on previous page. Green *Not required A CM9 POC Changes POC1 - HAZARD1/2 POC3 - (-) START POC4 - (-) IGNITION CM7/X POC Changes POC1 - HAZARD1/2 POC2 - (-) START POC3 - (-) IGNITION DC IGNITION LED Programming Error Codes Module LED flashing RED during programming 1x - No CAN activity, check connectors, check CAN voltages 2x - No immobilizer data, confirm connectors used 3x - VIN detection error, contact support 4x - No ignition, confirm connection and voltage CN1 - Blue (IGN) CM9 - Jumper to IGN1 CM7 - Jumper 2 to IGN CMX - HCP3 to IGN [3] E NI8/9 13 24 1 9 12 INSTALL GUIDE Page 30 of 32 Patent No. US 8,856,780 CA 2759622 COM-BLADE-AL(DL)-NI3-EN CARTRIDGE INSTALLATION 1 Slide cartridge into unit. Notice button under LED. 2 DOORLOCK INTERFACE NISSAN/INFINITI/AND BEYOND Doc. No.: ##75297## 20210412 Ready for Module Programming Procedure. MODULE PROGRAMMING PROCEDURE 1 ENGINE START x2 Push start button twice [2x] to ON position. STOP 3 ENGINE START x1 Push start button once [1x] to OFF position. STOP 2 Wait, LED will turn solid BLUE for 2 seconds. 4 Module Programming Procedure completed. WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020 INSTALL GUIDE Patent No. US 8,856,780 CA 2759622 DOORLOCK INTERFACE NISSAN/INFINITI/AND BEYOND Page 32 of 32 COM-BLADE-AL(DL)-NI3-EN Doc. No.: ##75297## 20210412 PUSH TO START VEHICLE TAKE OVER PROCEDURE - TO THE VEHICLE OWNER NOTE 4 I This procedure is to be followed during remote starter runtime prior to entering vehicle. II All vehicle doors must be closed. 5 1 Press UNLOCK on after-market remote or OEM fob. Press and release BRAKE pedal. It is safe to select gear ONLY AFTER LED indicator is in ON position. 2 Open vehicle door. Enter vehicle WITH THE OEM FOB. Close vehicle door. 3 LO O ACC CK O START STOP EN GI NE N N OR Wait for the LED indicator of the push button to be in the ON position. ENGINE ENGINE START OR STOP Wait for the ORANGE LED indicator of the push button to turn on. 6 Push to Start vehicle take over procedure completed. ! Failure to follow procedure may result in vehicle displaying CHECK ENGINE or TIRE PRESSURE error messages. WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020