Instruction Manual for EPSON models including: F2270 Large Format Printer, F2270, Large Format Printer, Format Printer, Printer
Epson SCF2270SE
Epson SureColor F2270 Standard Edition | Support | Epson US
File Info : application/pdf, 4 Pages, 1.89MB
DocumentDocumentEpson® SureColor® F2270
Start Here
IMPORTANT: Before using this product, make sure you read these instructions and the safety instructions in the online User's Guide.
Choose a Location for the Printer
Choose a location for the printer that is near a wall outlet where the power cord can be easily unplugged. Avoid places subject to rapid changes in temperature and humidity. Also keep the printer away from direct sunlight, strong light, or heat sources.
Make sure to place the printer on a flat, stable surface with enough space on all sides (see illustrations below). The surface supporting the printer should be wider than the space between the rubber feet on the bottom of the printer, between 23.6 to 31.5 in. (60 to 80 cm) off the ground, and capable of supporting approximately 242 pounds (110 kg).
21.4 in. (54.3 cm)
0.4 in. (1 cm)
Approx. 39.4 in. (100 cm)
Approx. 31.5 in. (80 cm)
Approx. 57.1 in. (145 cm)* 0.4 in. (1 cm)
26.1 in. (66.3 cm)
* Approx. 59.1 in. (150 cm) with optional L-size hanger platen.
Unpack and Place Printer
1 Make sure you have these items:
2 Remove all the packaging materials and tape. Check carefully for all the
tape inside and outside the printer and platen. WARNING: The printer requires four people to lift and move it. Make sure to
grip the printer where indicated by the gray stickers and * marks as shown in the illustration. The * marks denote non-slip pads under the printer where hands should be placed. All four people should lift simultaneously to avoid tilting the printer and trapping their hands.
Assemble the Printer
1 Make sure any protective material is removed from the back of the
printer.
2 Holding a wipe to the waste ink outlets, remove the plugs on the back
of the printer and then wipe the waste ink outlets as shown.
English
Epson America, Inc. Limited Commercial Warranty
A. What Is Covered: Epson America, Inc. ("Epson
rst end-user customer that the Epson®
SureColor® F2200 series printer ("Product") covered by this limited warranty, if purchased and used
cations and be
free from defects in workmanship and materials for a period of one (1) year from the date of original
purchase, or for 2,280,000 carriage passes 1
rst ("Warranty Period is limited
warranty is not transferable. Epson also warrants that the consumable ink included with the Product will
e limited warranty for the ink shipped with the Product
may expire before the expiration of the limited warranty for the Product.
Your printer is designed to use UltraChrome® DG2 ink and delivery systems. Any damage caused by using other inks or ink delivery systems, will not be covered under this limited warranty.
is limited warranty contains important legal terms and conditions, including an arbitration provision. Please review carefully.
B. What Epson Will Do To Correct Problems: If your Product requires service during the Warranty Period, please call toll free (888) 377-6611 (United States, Canada, and Puerto Rico). Support hours are c Time, Monday through Friday and are subject to change without notice. When you call, be prepared to provide the Epson technician with the Product serial number, the address where it is located, the original date of purchase, and a description of the problem. You may need ed by the serial number. An Epson technician will work with you to try to resolve the problem. If service is required, the on-site service e technician will provide additional instructions about the program at the time this service is being set up. At its sole discretion, Epson may instead elect to perform exchange service. For more details, please see Section C, On-Site Response and Section D, Product Exchange. When service involves the exchange of the Product or a part, the items replaced become the property of Epson. Replacement items assume the remaining Warranty Period of the original Product. Parts or Products exchanged may be new or remanufactured to Epson standards.
C. On-Site Response: If Epson determines a warranted hardware defect requires repair, Epson may elect to use on-site service. If this is the case, and the Product is within Epson's on-site service territory, an Epson-trained technician will repair the Product at your facility. Epson will usually dispatch repair parts and a technician to the Product's location for the next business day if Epson determines repair is required c Time, dispatch will usually be for the second business day. Parts shippe d to remote areas may require longer delivery times. An adult must be available to accept the shipment and be present at all times while the technician is onsite. Epson's shipment of parts does not imply that replacement is required.
D. Product Exchange: Epson may, at its sole discretion, elect to replace a Product that appears to require repair due to a warranted hardware defect. Under these rare circumstances, Epson will replace the Product with the same or a comparable product refurbished to the Epson standard of quality. Epson will ship a replacement product, freight prepaid, as long as your address is in the United States, Canada, e replacement product will not include promotional materials, accessories, stands, ware, or cables.) You must be able to receive, unpack, and install the replacement product, and prepare the defective Product for return shipment by following the procedures described in the User's Guide or documentation provided by Epson.
e repacked defective Product will be picked up by a carrier designated by Epson. If the defective Product is not returned within seven (7) business days of receipt of the replacement, you will be invoiced at the full price of the replacement printer. If the Product is returned damaged because you have not properly packed or shipped it, you will be billed for the damage. It is your responsibility to unpack, reinstall optional components, and set up the exchange printer at your location. Epson does not cover damage caused by improper installation.
1 Carriage passes can be viewed on the control panel display.
Limited warranty
Printer
Rear cover
Tweezers
Medium platen and hoop
Waste ink bottle
Waste ink tube
Note: Do not throw the plugs away; you need them if you transport the printer.
3 Connect the waste ink tube. Make sure that the longer end of the tube
is connected to the waste ink outlet on the left side and the shorter end is connected to the waste ink outlet on the right side.
Grip pad
Maintenance kit
Waste ink bottle holder
Ink labels
4 Attach the rear cover as shown.
Ink charging unit
Grip pad tool
Ink packs/maintenance liquid Tube/cable clamps
Wipes
Caution label
Zip ties
Power cord
Note: See the online User's Guide for information on installing the grip pad, using the grip pad tool, and using the maintenance kit and tweezers.
5 Tighten the rear cover screws.
11 Position the waste ink bottle beneath the right side
of the printer. The bottle and holder should be placed in an area lower than the printer so that the waste ink can flow straight down.
6 Open the printer cover and press down on the part as shown to make
sure it is secure.
WARNING: Fully open the printer cover as shown below. Otherwise, the cover could close, trapping your hand or fingers.
Note: Make sure the waste ink tube is not pinched anywhere or ink could leak inside or around the printer.
7 Close the printer cover.
WARNING: Be careful not to trap your hands or fingers when closing the printer cover.
8 Remove the carriage lock and store it in a safe place.
12 Open the clip at the top of the waste ink bottle holder.
Note: Do not throw the carriage lock away; you need it if you transport the printer.
9 Attach three tube clamps to the rear cover and route the waste ink tube
through the clamps as shown.
13 Place the tube next to the waste ink tube holder to check the length.
Cut the tube about 0.4 inch (1 cm) below the bottom of the tube holder as shown.
10 Remove the outer and inner caps from the waste ink bottle and store
them in a safe place.
14 Fasten zip ties to the waste ink tube as shown. They should sit above and
below the clip.
Note: Do not throw the caps away; you need them when disposing of the waste ink.
15 Insert the waste ink tube into the holder as shown and then close
the clip.
Install Ink Supply Units (Ink Packs)
Caution: Keep the ink packs out of the reach of children and do not drink the ink.
1 Pull one of the ink trays out of the printer.
16 Insert the waste ink bottle into the waste ink bottle holder. Then, place
the caution label for your language over the English label, if necessary.
2 Insert the ink pack into the tray and push it down as shown.
17 Connect the power cord to the back of the printer and plug the other
end into an outlet. (Do not connect the printer to your computer yet.)
Note: Make sure the ink pack fits onto the pegs and is aligned with the top of the tray.
3 While the ink pack is in the tray, carefully shake it by tilting it up and
down at about a 60 degree angle as shown. Shake white ink packs about 25 times and shake other color ink packs 5 times.
Turn On and Configure
1 Press the power button on the control panel to turn on the printer.
4 Match the color on the ink pack label with the color slot on the printer
and then use both hands to insert the ink tray into the printer.
2 Follow the on-screen instructions to select the language, date and time,
and measurement settings on the touchscreen.
3 Select the printer's ink mode from the touchscreen. 4 Open the ink covers.
Note: The ink packs are keyed to fit into the correct color slot. If you cannot insert the ink tray all the way, do not force it. Make sure the ink pack color matches the color slot on the printer.
5 Repeat steps 1 to 4 to install the other ink packs. Close the ink covers
after all of the ink packs have been installed.
5 Apply the ink labels for the selected ink mode as shown.
Note: Only use label set 2 if the printer will be using High speed color mode.
6 Follow the instructions on the touchscreen to load the ink charging
unit, if necessary, and to begin ink charging. Ink charging takes about 35 minutes and you see a message on the touchscreen when it is complete.
Caution: Do not turn off the printer, open any covers, or try to perform any other operations while the printer is charging or you'll waste ink.
Note:
· If you selected White ink mode or High speed color mode, use a glove to load the ink charging unit. After use, see the online User's Guide for information on how to properly dispose of these items.
· Make sure all of the ink trays are inserted in the product; otherwise printing is not possible.
Install Software
Note: An internet connection is required to obtain the product software.
1 Download and run your product's software package. For the latest
software and utilities, visit http://epson.com/support/f2270 (U.S.), http://epson.ca/support/f2270 (Canada), or http://latin.epson.com/support/f2270 (Caribbean).
2 Follow the instructions on the screen to run the setup program.
Product Support
User's Guide
Windows®: Click the icon on your desktop or Apps screen to access the online User's Guide.
Mac: Click the icon in Applications/Epson Software/Guide to access the online User's Guide.
If you don't have a User's Guide icon, go to the Epson website, as described in "Epson technical support."
Epson technical support
Visit http://epson.com/support/f2270 (U.S.), http://epson.ca/support/f2270 (Canada), or http://latin.epson.com/support/f2270 (Caribbean) to download software and utilities, view manuals, get FAQs and troubleshooting advice, or contact Epson.
Epson provides technical support and information on the installation, configuration, and operation of professional printing products through the Epson PreferredSM Limited Warranty Plan. Dial (888) 377-6611, 7 a.m. to 4 p.m., Pacific Time, Monday through Friday. Days and hours of support are subject to change without notice. Before you call, make sure you have your:
· Printer serial number: ________________________________________ · Proof of purchase and date: ____________________________________
Note: If you experience difficulty with the toll-free line, call (562) 276-1305.
Recycling
Epson offers a recycling program for end of life hardware and ink packs. Please go to http://epson.com/recycle (U.S.) or http://epson.ca/recycle (Canada) for information on how to return your products for proper disposal.
Need Ink?
You can purchase ink from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766).
SureColor F2270 replacement ink packs
Color
800 ml
Black
T54K120
Cyan
T54K220
Magenta
T54K320
Yellow
T54K420
White
T54KA20
EPSON and SureColor are registered trademarks and the EPSON logo is a registered logomark of Seiko Epson Corporation.
Epson Preferred is a service mark of Epson America, Inc.
Mac is a trademark of Apple Inc., registered in the U.S. and other countries.
Microsoft and Windows are trademarks of the Microsoft group of companies.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2023 Epson America, Inc., 6/23
Printed in U.S.A.
CPD-63664
Printer & Ink Cartridge Recycling Program | Epson CanadaSPT_SCF2270SE | Epson SureColor F2270 Standard Edition | SureColor Series | Single Function Inkjet Printers | Printers | Support | Epson Canada
Printer & Ink Cartridge Recycling Program | Epson USEpson SureColor F2270 Standard Edition | Support | Epson US
Epson