User Guide for ekwb models including: Z690 EK-Quantum Momentum VRM Bridge ROG Maximus, Z690, EK-Quantum Momentum VRM Bridge ROG Maximus, Momentum VRM Bridge ROG Maximus, VRM Bridge ROG Maximus, Bridge ROG Maximus, ROG Maximus, Maximus
EK WaterBlocks EK-Quantum Momentum2 VRM Bridge ROG Maximus Z690 Formula D-RGB - Plexi | すべての商品 | OLIOSPEC
Merlinhardver - EKWB EK-Quantum Momentum² VRM Bridge ROG Maximus Z690 Formula D-RGB - Plexi (3831109895856)
File Info : application/pdf, 11 Pages, 1.45MB
DocumentDocumentEK-Quantum Momentum2 VRM Bridge ROG Maximus Z690 Formula D-RGB MONOBLOCK USER GUIDE This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our website at www. ekwb.com for updates. Before installation of this product please read the important notice, disclosure, and warranty conditions printed on the back of the box. Before you start using this product, please follow these basic guidelines: Please carefully read the manual before beginning the installation process! The EK Fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber O-ring gaskets. The use of corrosion inhibiting coolants is always recommended for liquid cooling systems and mandatory for nickel-plated water blocks! Do not use pure distilled water! For best results, EK recommends the use of EK-CryoFuel coolants! Make sure to thoroughly bleed air out of your water block, or you will not achieve optimal performance! - 2 - TABLE OF CONTENTS BOX CONTENTS 4 WATER BLOCK DIMENSIONS 5 WATER BLOCK SPECIFICATIONS AND MAIN PARTS 6 INSTALLING AND ATTACHING THE WATER BLOCK 7 SUPPORT AND SERVICE 11 SOCIAL MEDIA 11 - 3 - BOX CONTENTS Mounting Mechanism Extender M12F (2 pcs) VRM Bridge Extender (2 pcs) EK-Quantum Momentum2 VRM Bridge ROG Maximus Z690 Formula D-RGB Allen Key 2.5 mm (1 pc) Grease (1 pc) EK-Loop Multi Allen Key (1 pc) - 4 - WATER BLOCK DIMENSIONS 18.1 mm 135 mm 36.6 mm 64.7 mm 71.5 mm 128 mm - 5 - WATER BLOCK SPECIFICATIONS AND MAIN PARTS 7 6 2 13 14 4 8 3 9 1 10 Technical Specification: - Dimensions: (LxHxW) - 128 x 135 x 18.1mm - D-RGB cable length: 500mm - D-RGB LED count: 19 - D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground) Position 1 2 3 4 5 6 7 8 9 10 11 12 13 14 EAN 105115 105116 105118 105117 100947 100663 104444 105166 104353 105120 8603 8011 104988 103155 Description Metal plate Acetal Standout Bottom plate (Plexi) Top plate (Plexi) Screw M3x6 ISO 7380 EK - Badge Mylar sticker O-Ring set Screw M3x12 7991DIN Acetal Standoff Metal washer M4 Screw M4x10 ISO 7380 Screw M4x18 7991DIN LED D-RGB Dense Strip - 500/130mm Quantity 1 1 1 1 3 1 1 1 13 3 3 3 1 1 11 5 12 - 6 - INSTALLING AND ATTACHING THE WATER BLOCK EXTENDER M12F PUSH-IN FITTING STEP 1 Install your EK-Quantum Velocity2 1700 water block in the illustrated orientation and place the motherboard on a secure flat surface. Using the enclosed EK-Loop Multi Key, install two (2) Extenders M12F and two (2) torque push-in fixation fittings to the pre-installed VRM block and CPU block (as shown in the image). Do not use excessive force while tightening the fittings. For this step, you will need: EK-Loop Multi Allen Key STEP 1 M4 x 18 DIN7991 SCREW STEP 2 STEP 2 Unscrew the one (1) M4 x 18 DIN7991 screw using the enclosed 2.5mm Allen key and remove it from the block. Save the screw for later step. For this step, you will need: Allen Key 2.5mm - 7 - PLEXI PLATE STEP 3 Slide the Plexi away from the black acetal stand-out with stainless steel fixation plate until it stops (approximately at 3 mm) 3 mm GAP STANDOUT (BLACK ACETAL) STEP 3 O-RING STEP 4 Before attempting to mount the water block, apply a small amount of the supplied grease to each of the four (4) O-Rings on the fixation fittings. Next, position the water block over the fixation fittings and force it into place evenly. For this step, you will need: Grease STEP 4 - 8 - M4 x 18 DIN7991 SCREW PLEXI PLATE ALLEN KEY M2.5 STEP 5 Push the plexi plate back to its original position and screw back the one (1) M4 x 18 DIN7991 screw that was removed in Step 2. Do not use excessive force while tightening the screw! For this step, you will need: Allen Key 2.5mm INLET STEP 5 OUTLET STEP 6 With the EK-Quantum Momentum2 VRM Bridge ROG Maximus Z690 Formula D-RGB water block, it is mandatory to use the bottom port as the INLET. Mixing the ports may result in poor thermal performance of the water block. Tighten the fittings in a clockwise direction until the gasket underneath is compressed. The installation of the water block is now complete. STEP 6 - 9 - D-RGB Header RGB Header STEP 7 Plug the 3-pin D-RGB connector from the bridge block in a D-RGB header on your motherboard or controller. The LED strip will only work if the pin layout on the header is as follows: +5V, Digital, Empty, Ground. Incorrect installation or installation of the incorrect header could result in damage to the LED strip or the header itself. STEP 7 - 10 - SUPPORT AND SERVICE In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact: https://www.ekwb.com/customer-support/ For spare parts orders, refer to the page with "TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS" where you can find the EAN number of each part you might need. Include the EAN number with quantity in your request. Mounting Mechanism EAN can be found under "BOX CONTENTS" SOCIAL MEDIA EKWaterBlocks @EKWaterBlocks ekwaterblocks EKWBofficial ekwaterblocks