User Manual for AVTECHSMART models including: AVALON100ZOOM, AVALON100ZOOM 100W White LED Gobo Projector, 100W White LED Gobo Projector, LED Gobo Projector, Gobo Projector, Projector
AVTech
AVALON100ZOOM-MANUAL - AVTech
File Info : application/pdf, 7 Pages, 589.14KB
DocumentDocumentAVALON10 0 ZOOM
100W White LED IP65 Gobo Projector
USER MANUAL
SW-305P user manual
Operate Introduc on
4 MODES DMX mode, Auto run mode, Master/Slave, Manual mode
DMX Channels13 Channels Func onDimming, color wheel, rota ng gobo wheel, focus, zoom, ripple effect,prism 4 menu bu onsLong press MODE+SET for 3 seconds to unlock, press MODE+SET in other interface to quickly lock
MODE SETUP
UP DOWN
Menu/Back to previous menu Confirm the selec on func on
Select the previous op on Select the next op on
Menu
Menu 1
1.DMX Address 2.Auto Mode
Menu 2 001 512 Auto Run Scene Edit
Menu 2 Scene1-Scene7
3. Slave 4.Manual Control
1.Dimmer: 0-255 2.Strobe: 0-255 3.Color: 0-255 4.ColorF: 0-2555 5.Gobo: 0-255 6.Gobo_R: 0-255 7.Gobo_F: 0-255 8.Focus: 0-255 9.Zoom: 0-255 10. Water 0-255 11. Prism: 0-255
Func ons
1.Dimmer: 0-255 2.Strobe: 0-255 3.Color: 0-255 4.ColorF: 0-255 5.Gobo: 0-255 6.Gobo_R: 0-255 7.Gobo_F: 0-255 8.Focus: 0-255 9.Zoom: 0-255 10. Water 0-255 11. Prism: 0-255 12. PrismR: 0-2555 13. Time: 0-255
12. PrismR: 0-2555
5.Se ngs
1.Curve Select
1.Linear
2.Square Law
3.InvSquareLaw
4.S-Curve
2.DMX Fail
Off
Hold
3.Display
Normal
Inverted
4.Language
English
Chinese
5.Key Lock
Lock a er 30s
Unlocked
6.Back Light
Off a er 60s
Always On
8.Default
No
Yes
6.Calibra ons Password
1.Color: 000-255
2.Gobo: 000-255
3.GoboR: 000-255
4.Focus: 000-255
5.Water: 0-255
6.Zoom: 000-255
7. Prism: 0-255
8.Default:
7.Informa on version and UID code
Menu descrip on:
1. DMX Address
Press the UP/DOWN bu on to set the ini al address code (001 ~ 512). A er se ng the
address code, press the SET bu on to confirm the save and automa cally exit to return
to the main menu. The fixture is in DMX mode a er this opera on.
2. Auto Mode Select the Auto Mode menu, there are two menus for op on, one is Auto Mode, another is Scene Edit with 7 scenes for edi ng. Each scene can be edited independently, and also includes all the DMX channels func on and me-keeping func on, but no Reset func on. The edi ng process is the same as Manual Control, exit to save. This fixture has a maximum of 7 gobos, so it can set 7 scenes. If you need less than 8 scenes, set the scene me-keeping to "0". The unit of me is seconds.
3. Slave
Select the Slave Mode menu, press the SET bu on to enter Slave Mode, then it will
receive the signal from the master and keep the same state as the master. The fixture in Auto Mode or Manual mode is the master. In the screensaver, it will switch to DMX mode in response to the channel sent from the console whenever the master or slave receives the DMX512 signal.
4. Manual Control Select the Manual Control menu, Press the UP/DOWN bu on to select which func on to operate. The right number a er pressing the SET bu on is selected. Then press the UP/DOWN bu on to modify the value, long press to con nuously modify, and press the SET bu on to change the op ons on the le . Press the MODE bu on to exit and return to the main menu. It will not exit the manual mode in this state. It's need to enter other modes for switching. For example, if you set the DMX address, then will enter the DMX mode.
5. Se ngs 1) Curve Select To choose one of linear dimming/square curve dimming/inverse square curve dimming/S-curve dimming. The characteris c of linear dimming is that the light output brightness maintains a linear rela onship with the channel value; square curve dimming is rela vely linear dimming, and the channel value range occupied in the low brightness area is more, that is the low brightness area is more abundantly adjusted; the low brightness area occupies few channels. When the channel value increases from 0 to up, the brightness quickly becomes very bright, and it allocates more channel value ranges in the high brightness area; the S-shaped curve is in the low brightness area Both the high-brightness area and the high-brightness area are allocated, and the medium-brightness area is few.
2) DMX Fail "OFF" (No DMX, ligh ng is off.), "HOLD" (No DMX, ligh ng keeps the original state).
3) Display The display reverse is used when the fixture is upside down.
4) Language English or Chinese
5) Key Lock When using the key lock func on, not key opera on a er 30 seconds, the key is locked.
Pressing the key in the locked state is invalid. It needs to press the MODE+SET key combina on for 3 seconds to unlock.
6) Back Light Select always on or 60S off if no opera on
7) Reset In order to verify whether the motor is working normally, and whether to save it a er
modifying the parameters, it can be perform a reset opera on, like re-powering on.
8) Default Restore the DMX address and parameters into factory values. The default address is 1,
and the gray background op on in the menu table is the default.
6. Calibra ons
Enter 088 on the Password interface and press SET to enter the Calibra ons menu. When the op on on the le is selected, press the UP/DOWN bu on to select which func on to operate. A er pressing the SET bu on, the number on the right is in the selected state. At this me, press the UP/DOWN bu on to modify the value. Long press can be modified con nuously. A er pressing the SET bu on again, it changes back to the le op on as the selected state. Press the SET bu on on the Default op on to restore the default value 127.
7. Informa on Display the fixture so ware version and UID code of RDM.
DMX Channel Func on Dimmer Strobe
Color
DMX Value 000-255 0-10 11-127 128-255 0~7 8~15 16~23 24~31 32~39 40~47 48~55 56~63 64~71 72~79 80~87 88~95 96~103 104~111 112~119 120~127
Se ng 0~100% Always on Random strobe slow to fast Linear strobe slow to fast White Color 1 Color 2 Color 3 Color 4 Color 5 Color 6 Color 7 white+ Color 1 Color 1+ Color 2 Color 2+ Color 3 Color 3+ Color 4 Color 4+ Color 5 Color 5+ Color 6 Color 6+ Color 7 Color 7+ white
13 Channels 1 2
3
ColorF Gobo
GoboR GoboF Focus Zoom Water Prism PrismR Func on
128~191
192~255
0-255 0~8 9~17 18~26 27~35 36~44 45~53 54~62 63~71 72~79 80~88 89~97 98~106 107~115 116~124 125~133 134~142 143~199
200~255
0~127 128~191
192~255
0-255 0~255 0~255 0~127 128-255 0~31 32~255 0~127 128~191
192~255
0~9 10~19 20-255
Clockwise rota on: fast to slow
Counterclockwise rota on: slow to
fast
Color wheel posi oning fine-tuning 4
Gobo 1 ( or White circle)
5
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 8
Gobo 8 shake from slow to fast
Gobo 7 shake from slow to fast
Gobo 6 shake from slow to fast
Gobo 5 shake from slow to fast
Gobo 4 shake from slow to fast
Gobo 3 shake from slow to fast
Gobo 2 shake from slow to fast
Gobo 1 not shake
Clockwise rota on fast to slow
Counterclockwise rota on slow to
fast
Sta c rota on by a certain angle
6
Clockwise rota on fast to slow
Counterclockwise rota on slow to
fast
Pa ern posi oning fine-tuning
7
Focusing
8
Zooming
9
No func on
10
Ripple from slow to fast
Prism close
11
Prism open
No rotate
12
Clockwise rota on fast to slow
Counterclockwise rota on slow to
fast
No ac on
13
All reset a er three seconds
No ac on
RDM suppot
Readable
Writable
RDM Support DISC_UNIQUE_BRANCH DISC_MUTE DISC_UN_MUTE
SUPPORTED_PARAMETERS
PARAMETER_DESCRIPTION
DEVICE_INFO DEVICE_MODEL_DESCRIPTIO N MANUFACTURER_LABEL DEVICE_LABEL FACTORY_DEFAULTS
LANGUAGE_CAPABILITIES LANGUAGE
SOFTWARE_VERSION_LABEL
DMX_START_ADDRESS
SENSOR_DEFINITION SENSOR_VALUE
RECORD_SENSORS
DISPLAY_INVERT IDENTIFY_DEVICE RESET_DEVICE CAPTURE_PRESET PRESET_PLAYBACK
FAC_RUN_MODE FAC_SAVE_RUN_MODE
Values 0x0001 0x0002 0x0003
0x0050
0x0051
0x0060
0x0080 0x0081 0x0082 0x0090
0x00A0 0x00B0
0x00C0
0x00F0
0x0200 0x0201
0x0202
0x0500 0x1000 0x1001 0x1030 0x1031
0xD320 0xD321
descrip on Search Locked Unlock Supported Parameters Custom parameter descrip on Device informa on Device model no. descrip on Manufacturer Device label Factory se ng Languages capabili es Languages So ware version descrip on DMX Start Address Sensor Defini on Sensor value Record sensor value Display reversed Iden fy device Reset Device Preset Playback Lamp Opera on Mode Save run mode
Customize
* Lamp opera ng mode descrip on: The data is 1 byte unsigned number, 0 means DMX mode, 1 means manual control mode, 2 means self-propelled mode, 3 means slave mode.
*Save opera on mode descrip on: The 0xD320 instruc on is only a temporary modifica on of the opera on mode. It needs to be saved with the 0xD321 instruc on. Write 1 to save the current opera on mode, and write 0 to restore the previously stored opera on mode.