Tesvor M1 Smart Robot Vacuum

1. Safety Instructions

To reduce the risk of injury or damage, read these safety instructions carefully and keep them at hand when setting up, using, and maintaining this device.

Safety Instructions for M1 and Accessories

Warning

Do not disassemble, repair or refit the product without authorization; otherwise, it may damage the product or pose a hazard. Do not use the device in an environment with a risk of fire or explosion. This device is only to be used with the original power adapter; otherwise, it may be damaged or catch fire. This device is not a toy. Do not sit or stand on this device. Small children and pets should be supervised when this device is operating. If the metal part of the power plug is dusty, please wipe it with a dry cloth. The power adapter is applied to a 100-240V AC voltage. Please plug it into the socket properly and keep away from children. Do not wash or soak the main body and electronic accessories in water; otherwise, the device may be damaged by a short circuit. Do not damage, load weight on, heat, pull, or bend it. During cleaning, please pay attention to the safety of toddlers and the elderly at home to avoid tripping, and to avoid injury please do not touch the wheel and side brush. (Please pay special attention to toddlers). This device is for indoor use only. Please do not use it outdoors. Do not allow metal and conductive materials to come in contact with the battery. It may result in a short circuit.

Do not touch the device with wet hands. It may result in an electric shock. Do not place the device where it could easily fall, such as on tables, chairs, high platforms in room, etc. The device has a sophisticated design and should be protected from long-term exposure to sunlight. Do not use the device in humid environments, such as bathrooms. Do not place the device near cigarette butts, lighters or open fires. Clean the product at the end of charging. Please turn off the power switch on the side of the robot when it is out of service for a long time.

Before using the device, please remove all vulnerable items on the floor, such as glass, lamps, and items such as wires and curtains that may become entangled with the side brush and suction passages. When the dust box is full, please empty it into the garbage before using it again. Do not use the robot to clean construction waste. The operating temperature of the device ranges from 0 degrees Celsius to 40 degrees Celsius; please do not use it in a high-temperature environment. Before the device is scrapped, please remove the battery from the robot. When you remove the battery, please ensure that the device is not connected to a power supply. Please recycle the battery safely for environmental protection.

Safety Instructions for M1 and Accessories

Danger

Always use a dedicated battery adapter to avoid leakage, heating or rupture. Do not short-circuit the battery or remove the battery. It may result in leakage, heating or rupture. Do not transport or preserve with necklaces, hairpins and other metal objects. It may result in a short circuit, leakage, heating or rupture. Do not burn or heat the battery. It may result in leakage, heating or rupture.

Warning

When skin or clothing is exposed to the battery electrolyte, please immediately wash with clean water to avoid inflammation of the skin, etc. Do not use the rechargeable battery on other devices. This battery is only suitable for the Tesvor robot vacuum cleaner. If the battery's outer box is found to be deformed and enlarged, or there is a leakage of electrolytes, do not charge or continue to use to avoid danger. Do not throw or inflict a strong impact on the battery. It may result in leakage, heating or rupture. Do not disassemble the battery pack. It may result in battery rupture and electrolyte outflow, leading to fire, explosion, and other dangers. This device can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the device in a safe way and understand the hazards involved. Children should be supervised to ensure they do not play with this device. Cleaning and maintenance must not be performed by children without adult supervision. This device contains batteries that can only be replaced by skilled people. Only use the detachable supply unit provided with this device to recharge the battery.

The power supply must be removed from the socket-outlet before cleaning or maintaining the device. The battery must be removed from the device before it is scrapped. The device must be disconnected from the mains supply when removing the battery. The battery should be disposed of safely.

How to remove the battery

• Take out the two screws on the battery cover with a screwdriver.
• Take off the battery cover.
• Take the battery out and unplug the electric wires to remove the battery.

If abnormal overheating is discovered during charging, stop using it immediately to avoid leakage, heating or rupture. To prolong the service life of the battery, please remove the battery and place it in a cool, dry environment if it is out of service for a long time; this will avoid leakage, heating or rupture. Do not soak the battery in water or let it come into contact with any liquid; otherwise, it may cause leakage, heating or rupture. Be sure to stop using it immediately in case of any problem (e.g., discoloration or deformation), to avoid leakage, heating or rupture. Always use tape to insulate the battery's electrode when recycling or disposing of it.

2. What's in the Box

The accessories provided may vary slightly by model. The following are typical contents:

• Illustration of the Main Body of the M1 Robot Vacuum.
• Illustration of the Charging Base.
• Illustration of the Remote Control (requires 2 AAA batteries, not included).
• Illustration of the Power Adapter.
• Illustration of the Cleaning Tool.
• Illustration of four Side Brushes.
• Illustration of a High-effective Filter and Sponge.

3. Using Your M1

Important Tips before Use

1. Remove power cords and small objects from the floor that may become entangled with the M1.
2. The M1 may climb on top of objects less than 0.63 in/16 mm in height. Remove these objects if possible.
3. Avoid narrow places, such as thresholds and aisles, to reduce the uncovered rate.
4. Do not manually move or operate the M1 with the remote control during cleaning, as this will clear its memory and re-plan its route, affecting efficiency.
5. Anti-drop sensors prevent falls down stairs. Ensure sensors are clean and avoid reflective/very dark floors. Use physical barriers for areas where the M1 may fall.
6. Organize furniture to ensure the M1 can clean effectively without getting stuck.

Preparation

1. Install the side brushes. Ensure 'L' and 'R' markings correspond.
2. Turn on the main power switch on the side of the M1. Remove the protective film before use.
3. Place the Charging Base on a hard, level surface against a wall.
4. Ensure clear space around the charging base: 3.3 ft (1 meter) to the left/right and 6.6 ft (2 meters) in front. Avoid placing mirrors or reflective objects in this area.
5. Install 2 AAA batteries (not included) into the remote control.

Remote Control Functions

• [Power On/Off]: Starts or stops cleaning.
• [Display Screen]: Shows current status and settings.
• [Plan Cleaning]: Initiates Smart Cleaning mode or pauses/resumes cleaning.
• [Confirm Suction Settings]: Adjusts suction power.
• [Edge Cleaning]: Initiates Edge Cleaning mode.
• [Return for Auto Charging]: Sends the M1 back to the charging base.
• [Direction Control]: Manually controls the M1's movement (forward, backward, turn).
• [Clock Settings]: Sets the current time.
• [Schedule]: Sets a scheduled cleaning time.

Note: For App users, please refer to the User Guide for App & Alexa. When the device is near the charging base or a virtual wall, it may not respond to remote control instructions. Remove batteries if the remote control is not used for a long time.

LED Indication

Charging Modes

• Method 1: Press the [Return for Auto Charging] button on the remote control to send the M1 to the Charging Base.
• Method 2: The M1 automatically returns to the charging base when cleaning is complete, or the battery is low. Ensure the charging base remains powered so the M1 can find it.

Switching Modes

Note: Make sure the power switch on the side of the M1 is turned on before use.

• Wake Up: If the M1 enters Sleep mode (indicator light off) after 10 minutes of inactivity, press any button on the remote control to wake it.
• Start: From Standby mode, press the [Power On/Off] button on the M1 or on the remote control to start cleaning.
• Pause: Press the [Plan Cleaning] button on the remote control to pause the M1. Press again to resume.

Note: If the M1 is out of service for a long time, turn off the power switch.

Cleaning Modes

1. Smart Cleaning: The M1 cleans intelligently based on your home environment. Start by pressing the [Plan Cleaning] button on the remote control.
2. Spot Cleaning: Cleans a specific area intensively in a spiral pattern, ideal for concentrated dust. The M1 stops after 2 minutes in this mode.
3. Edge Cleaning: The M1 slows down near walls and follows them to clean edges thoroughly. Start by pressing the [Edge Cleaning] button on the remote control.

Set Time and Scheduled Cleaning

Set Time

Note: Ensure the clock is set to your local time before setting a scheduled cleaning.

1. Ensure the main power switch on the M1 is turned on.
2. Press the [Clock Settings] button on the remote control. The time display will blink.
3. Use the [Direction Control] buttons to set the hour and minute. Ensure AM/PM is correct.
4. Press the [Clock Settings] button again to save.

Set a Scheduled Cleaning

You can schedule the M1 to start cleaning at a specified time. To cancel a previously scheduled cleaning session, press and hold the [Schedule] button for 3 seconds.

1. Ensure the clock is set to your local time before scheduling.
2. Ensure the main power switch on the M1 is turned on.
3. Press the [Schedule] button on the remote control. The schedule icon will blink.
4. Use the [Direction Control] buttons to set the desired cleaning hour and minute. Ensure AM/PM is correct.
5. Press the [Schedule] button again to save the scheduled cleaning time.

4. Cleaning and Maintenance

Regular cleaning and maintenance are essential for optimal performance. The frequency depends on your usage.

M1 Anatomy

Top & Side View:

• 1. Bumper
• 2. Control button
• 3. DC power jack
• 4. Power switch
• 5. Dust box release button

Bottom View:

• 1. Swivel Wheel
• 2. Charging shrapnel
• 3. Side brushes
• 4. Battery Compartment
• 5. Wheels
• 6. Rolling brush
• 7. Dust box

Charging Base Components:

• 1. Charging indicator light
• 2. DC power jack
• 3. Charging terminal

Dust Box Components:

• 1. Pre-filter
• 2. High-performance filter
• 3. Filter sponge
• 4. Dust box
• 5. Dust box cover

Clean the Rolling Brush

1. Open the rolling brush cover.
2. Remove the rolling brush shaft and clean off any debris and hair.

Clean the Side Brushes

Foreign substances, such as hair, can easily get tangled in the side brushes, and dirt may adhere to them. Be sure to clean them regularly.

1. Remove the side brushes.
2. Carefully unwind and remove any hair or string wrapped around the brushes or main unit.
3. Use a damp cloth to clean dust or reshape the brushes. Ensure brushes are completely dry before reattaching.

Note: Only use the side brushes when they are completely dry.

Clean the Dust Box and Filters

1. Remove the dust box.
2. Empty dirt and dust from the box.
3. Remove the high-performance filter and the pre-filter (basic filter).
4. Clean the high-performance filter.
5. Wash the dust box and pre-filter with water. Clean the high-performance filter with a brush.
6. Air dry the dust box, pre-filter, and high-performance filter thoroughly before reassembly.

Note: The dust box, pre-filter, filter sponge, and high-performance filter can be washed with water. Ensure they are completely air-dried before reassembly.

Replace the Side Brushes

The side brushes may become bent or damaged after a period of use. Pull off the old side brushes and snap the new ones into place.

Clean the Sensors and Charging Terminals

To maintain the best performance, clean the drop sensors and charging terminals regularly. Use a soft cloth or cleaning brush to clean the sensors (located on the bottom of the unit) and charging terminals (on the side of the unit and charging base) periodically.

5. Troubleshooting

6. Specification

7. Customer Service

For any issues, contact Tesvor via Online Service on the app or email service@tesvor.com.

FCC Compliance and Warnings

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Modification: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the device.

RF Radiation Exposure Statement: The Robotic Vacuum Cleaner complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. Caution: To maintain compliance with the FCC's RF exposure guideline, install the Robotic Vacuum Cleaner at least 7.9" (20 cm) from ALL persons. The transmitter of this device must not be co-located or operating in conjunction with any other antenna or transmitter.