Protium Smart Switch Instruction Manual
How To Setup Mobile app? ?
1. Search and download "SmartLife" on App store/Play Store, and Register your account on the app (Skip this step if you already have app).
Switch pairing with mobile App ?
(? Note: please restart your mobile phone before beginning setup process)
- Connect your phone to a 2.4G WIFI network and turn ON Bluetooth and Location. (Device does not support 5.0GHz Network, please turn off 5Ghz band in dual band router)
- Connect the Input Power to switch Terminals L (IN) and N. (Do not Connect load until switch connected to Wi-Fi)
Device connections to main power
Diagram Description: Shows input terminals (Earth, S, N, IN, OUT) for power and load connection, with Earth connected to an earth symbol. A 'protium' logo is visible.
Adding Wall switch (only dry/N contact)
Diagram Description: Illustrates connecting the smart switch to a wall switch via dry contact terminals (S1, S2). It details power input (S, N) and load output. Notes that S1 & N terminals are internally shorted. A 'protium' logo is visible.
Important Note: Do not connect Phase (Live) wire to S1 & S2 terminals, it will cause short circuit. ❌
- Open Smart Life app, Reset the switch and Click "+" on top right corner. (Switch will be shown in app automatically if it is in reset mode, click on this to add it)
- For manual addition: Go to Add Manually tab, Go to "Electrician" section, select "Switch (Wifi)". Click "Confirm indicator rapidly blink".
Reset Method: Press and Hold the Button on Switch for about 5-7 seconds until LED Starts blinking. (Press & Hold 5-6 seconds)
- Input Your wifi password and click "Confirm".
- After successful adding the device, re-name it as per your wish.
ADD Load to the switch: 7. Connect only Lout (wire to load). Neutral and earth to load can be connected from anywhere of house wiring.
Note: This device is compatible with Wall switch. Connect S1 & S2 terminals of smart Switch to two terminals back side of your wall switch. Each press on wall switch will toggle the state of this Smart switch. ✔️
Troubleshooting Smart life device ⚙️
Method 1: Using Mobile Hotspot
- Make One Spare Mobile as Hotspot.
- Keep Hotspot Name “Hotspot12”.
- Keep Password “12345678”.
- Do not use any special characters or space in hotspot name and password.
- Connect Your mobile (having Smart life app) to this "Hotspot12" Network using the above name and password.
- Reset the Switch and add device as per this manual (Refer first page).
Note: If the device connected by this method, please send your wifi Router details to our support team; they will help to bind the MAC address in your router.
Common problem during installation:
| Error Message | Probable Cause | What to do? |
|---|---|---|
| Device fail to connect wifi network | Wifi password error Router is not 2.4Ghz |
Check password Try Hotspot method above |
| LED Is not blinking after pressing the button on it | Wiring not as per Pic 1 There is no power in the Switch |
Check (L-IN) and N wire have power input Check Main Switch is ON |
| Load not turn ON/OFF | Load not connected properly Switch Doesn't have power |
Connect the load as per Pic. 2 Check the Switch input power |
| Device Auto ON/OFF without any timer | Connected Network is not configured IPV4 protocol | Configure wifi network as IPV4 |
| Alexa not Discovered the Device | Smart life Skill not enabled Wrong Account link to Alexa skill |
Contact our support team. Enable Smart life skill Use correct account credentials to link alexa skill |
SAFETY NOTICE ⚠️
CUT OFF THE MAIN SUPPLY BEFORE INSTALLATION
? CALL ELECTRICIAN IF YOU ARE NOT PROFESSIONAL.
Note: 16A capacity of the switch is based on resistive Maximum load. If you are using inductive /or capacitive load, please check the details of appliance connected to the switch before using these devices.
Wrong connection may cause short circuit. (Refer Circuit diagram for details)
For Warranty Claim
Contact service support whatsup +91-9718717702 (MON-FRI : 900Hrs to 1600Hrs)