Instruction Manual for JBC models including: RHN-A Articulated Hand Rest For Phnek Preheater Set, RHN-A, Articulated Hand Rest For Phnek Preheater Set, Hand Rest For Phnek Preheater Set, Rest For Phnek Preheater Set, Phnek Preheater Set, Preheater Set, Set
JBC RHN-A Articulated Right Hand Rest with Base for PHN Preheaters
INSTRUCTION MANUAL RHN Articulated Hand Rest for PHNEK Preheater Set This manual corresponds to the following reference: RHN-A Packing List The following items are included: Articulated Height Adj. Flange ........ 1 unit Shaft ................................ 1 unit Hand Rest Arm ............. 1 unit Ref. 0023991 Ref. 0024007 Base PHNE compatible ......................... 1 unit Headless Screw ....................................... 1 unit Ref. 0017057 Allen Key ..................................................... 1 unit Ref. 0013609 2 Manual ......................................................... 1 unit Ref. 0027888 Features Shaft Height Adjustment Flange Headless Screw Printed Corner Guides Hand Rest Base Articulated Hand Rest Arm ESD Connector (connect to ESD Common Grounding Point) Positioning Bolds Assembly Height Adjustment Flange 3 Setting up the Hand Rest Arm Fit the shaft into the base bushing (1) and tighten the headless screw (2). Then assemble first the height adjustment flange (3) and finally the hand rest arm (4) onto the shaft. Shaft Base Bushing The hand rest arm position should be as shown in the image. The right hand rest is marked at its bottom side with the letter "R". Hand Rest Arm 4 1 2 Headless Screw (at the back) Right Hand Rest R R Bottom View 3 Height Adjustment According to your work needs the hand rest arm allows adjustment for different heights through the vertical axis. Slide the arm to the appropriate height (1) and secure it by tightening the knob (2) to guarantee stability. 1 2 Work Position Adjustment Arm Knob RHN arm allows adjustment for different positions according to your work needs. The articulated arm covers all work areas. JTT Position the arm and tighten the knobs. The correct hand position is shown in the following images: 4 Preheater Positioning RHN has been designed to work together with PHN Fit PHNE onto the positioning bolts (1) for proper alignment. The four corner guides (2) help to place the heater unit in its position. Positioning Caps 1 1 Corner Guides 2 If a fixed preheater position is not wanted the positioning bolts can be removed with a screwdriver. Positioning Bolds Note: for each preheater size, there are different articulated hand rests with different base dimensions available. Preheater PHNE PHSE PHBE Articulated Hand Rest RHN RHS RHB Base Dimension 310 x 239 mm / 12.20 x 9.41 in 400 x 270 mm / 15.75 x 10.63 in 550 x 480 mm / 21.65 x 18.90 in 5 Accessories* If a second hand rest ist needed, Articulated Left Hand Rest HRL is available. HRL also allows adjustment for different positions. HRL Articulated Left Hand Rest In the case of using both left and right arms, assemble both as shown in the illustration according to the letters on the back of the hand rest, to keep the hand supports at the same level. The right hand rest should be assembled below the left hand rest. HRL Articulated Left Hand Rest Bottom View L HRR Articulated Right Hand Rest Mark for right hand rest R L Mark for left hand rest 6 R Bottom View * Not included, sold separately. Compatible JBC Articles* HRR and HRL can be combined with: RWT Adjustable Rework Arm, RWS Adjustable Rework Arm for PHSE and RWB Adjustable Rework Arm for PHBE. Assemble first the height adjustment flange (1), then the HRR (2) and afterward the HRL (3). Assemble the second height adjustment flange (4) and finally the RWT (5). Heights Adjustmet Flange (2nd) RWT Ajustable Rework Arm HRL Articulated Left Hand Rest Heights Adjustmet Flange (1st) Place the preheater set in the area below the hot air tool HRR Articulated Right Hand Rest 4 different sizes for PCB Supports are available: - PHNS Support for PCBs up to 11x7 cm / 4x3" - PHSS Support for PCBs up to 13x13 cm / 5x5" - PHBS Support for PCBs up to 36x28 cm / 14x11" - PHXLS Support for PCBs up to 51x61 cm / 20x24" * Not included, sold separately. 7 Maintenance - Check periodically that RHN is clean, especially the sliding parts and the shaft. - Use a damp cloth when cleaning. Alcohol can only be used to clean the metal parts. - Replace any defective damaged parts. Use original JBC spare parts only. Do not leave up HRR over the preheater when the preheater is working. Shaft Sliding Parts Safety It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosions. - Do not use the equipment for any purpose other than PCB rework. - The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care. - Be careful with the fumes produced when soldering. - Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm. - Do not leave up the arms directly above heat surfaces. - Utmost care must be taken with liquid tin waste which can cause burns. - This appliance can be used by children over the age of eight as well as persons with reduced physical, sensory or mental capabilities or lacking experience provided that they have been given adequate supervision or instruction concerning the use of the appliance and understand the hazards involved. Children must not play with the appliance. - Maintenance must not be carried out by children unless supervised. 8 Notes 9 Notes 10 Notes 11 Specifications RHN Articulated Hand Rest for PHNEK Preheater Set Ref.: RHN-A - Base Dimensions: - Total Height: - Arm Heigth: - Arm Lenght: - ESD Connector 310 x 239 mm / 12.20 x 9.41 in 205 mm / 8.07 in 200 mm / 7.87 in 498 mm / 19.61 in - Total Net Weight: - Package Dimension / Weight: (L x W x H) 4.50 kg / 9.92 lb 370 x 204 x 370 mm / 6.09 kg 14.57 x 8.03 x 14.57 in / 13.43 lb Complies with CE standards ESD Safe Warranty JBC's 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased. This product should not be thrown in the garbage. In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility. 0027888-111122PDFium PDFium