Instruction Manual for MOUNT-IT models including: MI-1765KB Tray for Wall or Pole Mounting, MI-1765KB, Tray for Wall or Pole Mounting, Wall or Pole Mounting, Pole Mounting, Mounting
MI-1765KB Please scan this QR code to visit the product page. MONITOR MOUNT WITH WALL MOUNT PLATE, CLAMP AND KEYBOARD TRAY Thank you for choosing Mount-It Mount-It! Mount-It! 2~7kg (4.4~15.4lbs) 2 Mount and Accessories Spring Arm Wall Mount Decorative Plate Cover Hex Wrench Hex Wrench Pole Clamp Wrench Mousepad Alternate Bolt Nut Keyboard Tray Lag Screw Concrete Anchor Check carefully to make sure there are no missing or defective parts. Some hardware provided may not be used. Use the correct mounting hardware suitable for your installation. CHOKING HAZARD. Package includes small parts. Not for children under 3 years. Adult supervision is required. Missing Parts? Call us at (855) 925-5668 and we will ship replacement parts free of charge. DIMENSIONS & WEIGHT CAPACITY 25.7" 5.9" 2" 1.4" 6.7" max7.9" Ø1.1"~Ø2.4" 4.1" 2.6" Rated weight capacity is 4.4lbs~15.4lbs for the mount. Caution: Ensure all mounting surfaces are capable of holding the weight of your mount. DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! 3 Step 1 Step 1a-1 A. Wood Stud Mounting Option · With a stud finder locate the stud and center the Wall Mount Plate (#B) on the stud at the desired height. Using a bubble level to ensure straightness mark the center of the mounting holes with a pencil. · Use a 3/16" drill bit and drill on the marked locations to a depth of 2.2". Secure the Wall Mount Plate (#B) to the wall using Lag Screws (#W-A) and Washers (#W-C). Tighten the screws until secure. B. Concrete/Brick Mounting Option · Using a bubble level to ensure straightness hold the Wall Mount Plate (#B) to the desired location on the wall and mark the center of the mounting holes with a pencil. · Use a 3/8" drill bit and drill on the marked locations to a depth of 2.4". Clear any dust and debris from the holes and insert the Concrete Anchors (#W-B). Secure the Wall Mount Plate (#B) to the wall using Lag Screws (#W-A) and Washers (#W-C). Tighten the screws until secure. 4 5 Step 1a-2 Insert Decorative Covers · Insert the Decorative Covers (#C) into each of the bolt holes. Step 2 Attach the Spring Arm to the Mount Step 1b Pole Clamp Mounting Option Attaching the Pole Clamp (Pole Diameters Between 1.1"-1.8") · Using Hex Wrench (#E) loosen the two bolts on the Pole Clamp (#F) until the clamp opens wide enough to slide onto the pole. · Move the Clamp to the desired height and tighten the bolts back down until secure. · Place the end of the Spring Arm (#A) onto the end of the Wall Mount or Pole Mount. Tighten the bolt on the back of the Spring Arm to secure the arm to the mount. Attaching the Pole Clamp (Pole Diameters Between 1.8"-2.4") · Using Hex Wrench (#E) remove the two bolts from the Pole Clamp (#F) and replace them with the Alternate Bolts (#G). After installing the alternate bolts, adjust the width of the clamp to be slightly larger than the pole. · Move the Clamp to the desired height and tighten the bolts back down until secure. 6 7 Step 3 Step 3a-1 Attach the Keyboard Tray · Attach the Keyboard Tray (#K) to the end of the Spring Arm (#A) using Bolts (#M-A). Secure the bolts on the opposite side using Washers (#M-C) and Nuts (#I). · Place the Mousepad (#J) on the Keyboard Tray. Step 3b-1 Optional Monitor Instructions: Install the Top Bolts to the Monitor · Select the appropriate size mounting bolt (#M-A, M-B)for your display's mounting holes and verify the length of the VESA bolt is not too long. If you are unsure of the correct bolt size for your display refer to your user manual or contact the monitor manufacturer for sizing information. · After selecting the appropriate bolt install the top two bolts and washers (#M-C) to the monitor leaving a gap of approximately 0.1" (3mm). Step 3a-2 Cable Management · Cables can be run through the cable management clips on the underside of the spring arm. Step 3b-2 Attaching the Monitor · Hang the monitor onto the top of the VESA plate as shown. · Install the lower two bolts and washers (#M-C) through the lower holes. Tighten all 4 bolts until secure, do not over tighten. 8 9 Step 4 Final Adjustments · Cables can be run through the cable management clips on the underside of the spring arm. CAUTION: This monitor mount utilizes a mechanical spring assembly that does not require tension adjustments to balance the weight of the monitor. Do not loosen the spring cover bolts. Removing the cover will detach the spring and it will be unable to be reattached. Any adjustment to these parts will cause irreversible damage to the monitor arm. · The viewing angle can be adjusted in the range of -45° to +90°, and the screen can be rotated 360°. Each joint can swivel left or right for alternate viewing angles. 10 11Adobe PDF library 15.00 Adobe Illustrator(R) 24.0