Instruction Manual for ACOVA models including: ISO9001 Anthracite Horizontal Designer Radiator, ISO9001, Anthracite Horizontal Designer Radiator, Horizontal Designer Radiator, Designer Radiator, Radiator
A B C E F D Assembly Instructions Sufficient PTFE tape must be applied to valve-tail threads prior to their installation. Silicone thread sealant should be applied to all threaded
File Info : application/pdf, 2 Pages, 558.83KB
DocumentDocumentThis manual is a guide to the installation and maintenance of this column radiator. Please register within 30 days in order to qualify for your warranty. The radiator must be installed in accordance with BS7593 and to the recognised water treatment procedures and standards. Failure to correctly dose the heating circuit can cause the radiator to corrode immediately and will negate the warranty. The system should be tested with the annual service and details can be entered on this document. All images and details contained are subject to change and should be checked before installation. Assembly Instructions Sufficient PTFE tape must be applied to valve-tail threads prior to their installation. Silicone thread sealant should be applied to all threaded components manufactured with `O-rings'. · Fit valve tails, using correct size Allen key. Accurately mark out bracket holes on wall. Drill 10mm diameter holes in wall to a minimum depth of 65mm and insert wall plugs (B). · Attach brackets (C) to wall with screws (D) as shown and level. Tightly fix the radiator tubes into the upper clamp assemblies (E). Loosely fit the lower clamp assemblies (E) to the radiator. · Lift the radiator on to the wall and locate the upper clamp assemblies (E) into the slots in the upper brackets (B). · Slide the lower clamp assemblies (E) until they locate in the slots in the lower brackets (B) and tighten clamps. · Fix security clip (F) into position over upper clamps (E). Security clips must always be placed in the top left and top right brackets when A mounting the radiator. · Due to the unique flow diverter built within all column radiators the flow MUST be on the same side as the permanent blank which is diagonally opposite to the air vent bleed valve. This radiator should be installed onto a central heating system that has been cleaned/flushed and contains water treatment and inhibitors in accordance with BS7593. Key Component Quantity A Air Vent - 1/2" (factory fitted) 1 B Wall Plug* 4 C Bracket 4 D Screw - Hex Head* 4 E Clamp Assembly 4 F Security Clip 2 * Wall plugs and screws not supplied Clamp Assembly (E) 4 x BH Height up to 1.5m, max 20 sections 1.5m+, max 10 sections 6 x BH Height up to 1.5m, >20 sections 1.5m+, >10 sections Security Clip (F) Bracket (C) 2 x 4 x CVD 2 x 6 x CVD Tools & Material Required Wall plugs - 10mm Screws - 7mm diameter x 60mm length Suitable valves PTFE tape Silicone thread sealant Tape measure Allen key - 13mm - 14mm Socket driver - 10mm long reach Electric drill Masonry drill bit - 10mm diameter Spirit level E F D C B Scan this QR Code to register your warranty. Dimensions, Bracket and Security Clip Positions D2 D2 P2 62 100 P1 width D1 2 column D1 3 column width ** Min 110 D2 136 D1 4 column D1 2 column D2 D1 3 column D2 D1 4 column D2 P1 P2 54 59 85 90 73 78 123 128 91 96 159 164 Min 110 width ** V0722 Acova Column Radiator Instructions height Min 65 33 (29 for 2 column) height Min 65 F pipe centres R = width + valves 105 105 All dimensions shown are in millimetres Test pressure: 15 BAR Max working pressure: 10 BAR Max working temperature: 110º C All steel construction: dia 25mm tubes Connections: 1/2 inch BSP btm opp end tappings Not suitable for use on domestic hot water system Heat output determined in accordance with EN 442 Test Laboratory: WSP-LAB, Test Lab Registration No: 1428 105 1/2 1/2 105 * = Security Clip = Diverter = Air Vent ISO9001 ISO14001 ISO50001