Summer Infant 3Dquickclose CS+ Compact Fold Stroller
Instruction Manual
Important Safety Information
Please read these instructions carefully and keep this manual for future reference. No tools are required for assembly.
For technical support, contact Summer Infant at 1-401-671-6551 or visit www.summerinfant.com/contact.
Warning: Keep small parts away from children. Adult assembly is required. Exercise care when unpacking and assembling the product.
General Warnings:
- Failure to follow all warnings and instructions could result in serious injury or death.
- Maximum weight and height of child: 50 lbs. (22.7 kg), 43 in. (109cm).
- Never leave a child unattended.
- Always use the safety harness to prevent serious injury from falling or sliding out.
- Ensure all parts of a child's body are clear of any moving parts when making adjustments.
- Care must be taken when folding and unfolding to prevent finger entrapment.
- Do not carry additional children, goods, or accessories unless recommended by the manufacturer.
- Do not use the storage basket as a child carrier.
- Do not hang items on the handle bar or canopy, as this can tip the stroller over.
- Do not overload the storage basket. Maximum weight: 25 lbs. (11.3 kg).
- Using parcel bags other than the recommended one may make the product unstable.
- Do not overload the storage pocket, cell phone holder, or cup holder. Maximum weight for cell phone and cup holder is 1 lb. (0.45 kg). Maximum weight for storage pocket and child cup holder is 1/2 lb. (0.23 kg). Excessive weight can cause instability or tipping.
- Do not place hot liquids in the cup holder; spills can burn your child.
- Do not carry or roll the stroller on stairs or escalators with a child in it.
- Do not use the stroller if any part is lost or damaged.
- Never install an Infant Car Seat without securely fastening it with the provided car seat straps.
- Never lift the stroller by the infant carrier handle.
- Compatibility: Use only with Summer™ Affirm™ 335, Graco® SnugRide® Click Connect™ 35, Graco® SnugRide® SnugLock® 35, Chicco® Keyfit® 30, Chicco® Fit2®, and Baby Trend® Secure Snap Gear® 35 Infant Car Seats. Other car seats or carriers are not designed to fit this stroller frame and may result in serious injury or death. Never use them if they have not been safety tested.
- Car seat must be in a rear-facing position only.
Components
Important: Before assembly, inspect this product for damaged hardware, loose joints, or missing parts. Never use if any parts are missing or broken.
Main Components:
- A: Stroller Frame with Seat
- B: Front Wheels (2)
- C: Rear Wheels (2)
- D: Bumper Bar
- E: Cup Holder
- F: Cell Phone Holder
3D-pac CS+ Stroller Replacement Parts:
Front Wheels | 32723-24 | Cell Phone Holder | 32453-03 |
Rear Wheels | 32723-22 | Bumper Bar | 31900-05 |
Cup Holder | 21790-25 | Car Seat Strap Set | 32453-04 |
Features
- Peek-a-boo window
- Soft handles
- Cup holder
- 5-point safety harness
- Car seat straps
- Bumper bar release buttons
- Storage basket
- Front wheel release tabs
- Storage pocket
- Cell phone holder
- Seat recline clip
- Rear wheel brake pedal
- Canopy
- Canopy extension
- Harness pads
- Bumper bar
- Child/bottle cup holder
- Adjustable leg rest
- Front wheel locks
- Dual action fold release
- Tuck away carry strap
- Rear wheel release tabs
Assembly Instructions
- Step 1: Slide the upper handle button, then squeeze the lower handle release button.
- Step 2: Quickly pull up the stroller by the handle bars until it clicks into the fully open position. The stroller will lock open. (Note: Ensure children are at a safe distance when opening the stroller.)
- Step 3: Align the front and rear wheels and push them into the frame. (Test each wheel by tugging to ensure it is securely attached and the front wheels turn freely.)
- Step 4: Snap the bumper bar into position. (You will hear a click when it is secured.)
- Step 5: Line up the slot on the back of the cup holder with a mounting post and push down. Repeat for the cell phone holder. (Note: The cell phone and cup holders are interchangeable to either side. Max weight for cup holder is 1 lb; for storage pocket is 1/2 lb.)
- Step 6: Extend the canopy forward. The canopy visor is tucked beneath the canopy; pull it down to extend it.
Assembly is now finished!
Operating the Harness
Locking/Unlocking 5-Point Safety Harness:
To lock: Press the buckle. To unlock: Press the release button on the buckle.
Tightening and Loosening the 5-Point Safety Harness:
To tighten: Slide the strap adjusters upwards. To loosen: Slide the strap adjusters downwards.
Adjusting Shoulder Harness Position
1. Unclip harness clips.
2. Remove harness pads.
3. Slide shoulder harness out of the slot. Adjust harness position as shown (upper, middle, or lower position) and reinstall harness pads.
Wheel Operation
Locking & Unlocking the Front Wheels:
To lock front swivel wheels: Rotate the lever until it faces the front. To unlock front wheels: Rotate the lever inwards.
Rear Brake:
To lock rear wheels: Press the foot pedal down. To unlock rear wheels: Press the foot pedal forward.
Seat and Leg Rest Adjustment
Adjusting the Seat Recline:
Pinch the seat recline clip on the back of the stroller and slide the recline clip along the webbing to adjust the seat recline.
Adjusting the Leg Rest:
To raise leg rest: Lift it up until it locks into the desired position. To lower leg rest: Press the buttons on the side of the leg rest and rotate the leg rest down.
Additional Features
Child Bottle/Cup Holder:
Slide a baby bottle or sippy cup into the side holder.
Peek-a-Boo Window:
Flip up the peek-a-boo window on top of the canopy.
Folding the Stroller
- Step 1: Flip the canopy extension into its storage position prior to folding the canopy.
- Step 2: First, slide the upper handle button, then squeeze the lower handle release button. The stroller will quickly close as shown.
- Step 3: The carry strap is stored in the pocket underneath the leg rest.
Warning: Strangulation Hazard: Children have been strangled when straps have wrapped around their neck. Keep this stroller carrier strap out of children's reach. When not in use, tuck the strap into the storage pocket beneath the seat.
Removing Parts
Removing the Bumper Bar:
Press the buttons beneath the bumper bar knuckles to remove.
Removing the Wheels:
Each wheel has a release tab. Pull the release tabs out to remove wheels from the frame.
Attaching a Car Seat
Compatible Car Seat Models: Summer™ Affirm™ 335, Graco® SnugRide® Click Connect™ 35, Graco® SnugRide® SnugLock® 35, Chicco® Keyfit® 30, Chicco® Fit2®, and Baby Trend® Secure Snap Gear® 35 Infant Car Seats.
Warning: Important! Keep for Future Reference!
- Never install an Infant Car Seat without fastening it securely to the stroller with the provided car seat straps.
- Car seat must be in a rear-facing position only.
- Never lift the stroller by the infant carrier handle.
- Use only with the compatible car seats listed above. Other car seats or carriers are not designed to fit this stroller frame and may result in serious injury or death. Never use them if they have not been safety tested.
- Step 1: Remove the bumper bar (press buttons to release).
- Step 2: Fold the canopy back.
- Step 3: Make sure the stroller seat is fully reclined.
- Step 4: Place the car seat into the stroller in the rear-facing position so it is in full contact with the stroller seating surface and seat back. Rotate the leg rest up until it is in the horizontal position. (Note: Check car seat for a secure fit in the stroller.)
- Step 5: Place the two car seat straps, attached to the stroller rails, into the Vehicle Belt Hooks and across the car seat. Lock the buckle. Slide the padded buckle guard over the buckle. (Note: Car seat straps and protective covers can be stored in the pockets on the side of the stroller.)
Warning: Avoid serious injury from falling or sliding out. Always place the car seat straps into the Vehicle Belt Hooks on the car seat and raise the leg rest up until it is in contact with the back of the car seat in its locked-in position.
Care and Maintenance
- Clean minor stains on fabric with cold water and mild soap.
- Clean plastic and metal surfaces with a soft damp cloth. Air dry. Do not use abrasive cleaners or solvents. Do not use bleach.
- Check seat pad, harness, and crotch straps weekly to ensure they are properly secured to the frame.