Raditeq RadiCentre® Modular Test System
Quick Start Guide
Models: CTR1009B | CTR1004B
Publish date: 28/05/2021
How to start the RadiCentre®
- Make sure that the connections to the plug-in cards are made correctly.
- Make sure that the hardware interlock plug of the RadiCentre® system is correctly installed.
- Plug the mains cord into the mains inlet of the RadiCentre®.
- Switch the mains switch at the rear of the RadiCentre® to the 'ON' position.
- Tap the touchscreen on the front panel to activate the RadiCentre®.
- Plug-in cards will automatically be detected and initialized by the RadiCentre®.
Rear Panel Overview:Diagram showing the rear panel of the RadiCentre® unit with labeled connection points: MAINS INLETS, INTERLOCK, PLUG-IN CARDS, FIRMWARE UPDATE, MAINS SWITCH.
How to install the Interlock
The RadiCentre® (Pro) uses a hardware interlock plug (6.3mm ¼" stereo jack) for safety. This plug provides two floating contacts that require connection for the system to operate.
By default, the supplied interlock plug is shorted and must be inserted into the interlock input at the back of the RadiCentre®. When used with an external interlock system (e.g., a door switch), the wires need to be connected in series with your interlock system and/or emergency stop circuitry. In this case, cut the RED wire and connect the open ends to your interlock system.
Refer to the relevant RadiCentre® manual for more information regarding the functionality of the interlock system. All Raditeq manuals can be found at: www.raditeq.com/products
Interlock Plug:Illustration of a 6.3mm (1/4") stereo jack plug with red and black wires, labeled "Interlock Plug". Text indicates: "Proper installation required. Please read the provided Quick Start Guide."
Warnings & Precautions
- Read the contents of this product manual carefully and become familiar with the safety markings, product instructions, and handling of the system. Refer to applicable product manuals for further information on operation and control.
- This product requires a protective earth connection. The mains power source must supply an uninterrupted safety ground to the IEC input connector(s).
- Only Raditeq qualified maintenance personnel are allowed to perform maintenance and/or repair service on the equipment.
- This product contains materials that can be recycled and reused to minimize material waste. At the 'end-of-life', specialized companies can dismantle the discarded system. If your product is at its 'end-of-life', please return it to your local reseller or to Raditeq for recycling.
- Ensure that airflow through the in- and outlets of this product is not restricted to maintain a constant temperature. The cooling system is designed for the specified operating temperature range.
- Position the product so that power cables are easily accessible or connect it to a mains network that can be easily disconnected.
- For cleaning, use a clean, dry cloth (or a damp cloth where needed) and wipe the surface of the equipment.
- This product contains no hazardous substances as described in the RoHS Directive (2015/863/EU).
- This product contains embedded software, which is field upgradeable from the RadiCentre® using the USB-A connection port on the backside panel. For more information about updating your Raditeq plug-in card, please read the RadiCentre® manual.
- Ensure that at least one slot of 1U height is kept empty below the RadiCentre® to ensure sufficient cooling through the bottom air inlets. The temperature of the amplifiers inlet cooling air must not exceed +45°C. The outlet air temperature should be maximum 20° higher than the inlet temperature.
Please keep this Quick Start Guide close at hand when operating your Raditeq equipment. For more information, consult your product manual or visit www.raditeq.com. Visuals used are examples and may differ from your product version.
Copyright © 2008 - 2021 Raditeq B.V.
Optimize your EMC test system
Configure your fully automated EMC test system with the extensive range of Raditeq products!
For more information about Raditeq's EMC and RF products, visit our website at www.raditeq.com.
Raditeq Featured Products
- RadiMation: Automated EMC & RF software.
- Electric Field Probes
- Electric Field Generators
- Modular test systems (e.g., RadiCentre)
For all Manuals, Datasheets and Quick start Guides, please visit: www.raditeq.com/support/downloads
