User Guide for DEWALT models including: DW1, DW2, DW3, D-CLIP Wire Component, D-CLIP, Wire Component, Component
8 дней назад — in the sMACNA HVAC Duct Construction standards (HVAC-DCs), 4th Edition, Chapter 5,. Tables 5-1, 5-1M and 5-2. GUIDE SPECIFICATIONS. 3 05 29 - Hangers and ...
CABLE HANGERS ANCHORS & FASTENERS GENERAL INFORMATION GENERAL INFORMATION D-CLIP Wire Component PRODUCT DESCRIPTION The D-Clip Wire Component is a one piece clip that is used to fasten TOUGHWIrETM to the mounting surface. Can be mounted on flat or sloped surfaces. TOUGHWIrETM Loop End Wire Assembly products (sold separately) are looped through the D-Clip, then anchored to the structure with a variety of DEWALT® Anchors and Fasteners (sold separately). SECTION CONTENTS General Information.........................1 Material Specifications ...................2 Installation Specifications ..............2 Installation Instructions..................2 Performance Data............................3 Conditions of Use.............................4 Ordering Information.......................4 GENERAL APPLICATIONS AND USES · HVAC duct · Electrical and mechanical systems · Luminaires and lighting systems · Plumbing & piping supports · signage and displays · Office partitions and panels FEATURE AND BENEFITS + Multiple sizes - Avaliable in 5/16 in. hole size and 1/2 in. hole size to pair with DEWALT® Anchors And Fasteners (sold separately). + Versatile Hanging - Can be mounted on flat or sloped surfaces. + ToughWireTM Compatible - Can be used with all three ToughWireTM wire diameters (DW1, DW2, and DW3, sold separately). APPROVALS AND LISTINGS · International Code Council, Evaluation service (ICC-Es), PMG-1786, Hangers for Pipe, Duct and Conduit support · Code compliant with the 2024, 2021, 2018 and 2015 IMC, IPC, IrC, UMC and UPC · Tested in accordance with ICC-Es LC1041 for supports and hangers for pipe, ducts and conduit · Tested and verified to be an acceptable alternative to the duct hanger systems prescribed in the sMACNA HVAC Duct Construction standards (HVAC-DCs), 4th Edition, Chapter 5, Tables 5-1, 5-1M and 5-2 GUIDE SPECIFICATIONS 3 05 29 - Hangers and supports for HVAC Piping and Equipment and 22 05 29 - Hangers and supports for Plumbing Piping and Equipment. Hangers shall be TOUGHWIrETM system as supplied by DEWALT, Towson, MD. Hangers shall be installed in accordance with published instructions and the Authority Having Jurisdiction. D-CLIP DEVCE MATERIAL · Zinc Plated Carbon steel SIZE RANGE · 5/16" Hole · 1/2" Hole SUITABLE MATERIAL PAIRING · TOUGHWIrETM Loop End Wire Assembly CODE LISTED ICC-ES PMG-1786 TECHNICAL GUIDE CAbLE HANGErs ©2025 DEWALT rEV. A 1 MATERIAL SPECIFICATIONS CABLE HANGERS MATERIAL SPECIFICATIONS Hanger/Device Component D-Clip Zinc Plating Component Material Carbon steel AsTM b633 (Fe/Zn5) Min. plating requirements for mild service condition INSTALLATION SPECIFICATIONS Description Clearance Hole Size Suggested DEWALT® Anchor(s) D-Clip for 1/4" Anchor/Fastener 5/16" 1/4" screw-bolt+ D-Clip for 3/8" Anchor/Fastener 1/2" 3/8" screw-bolt+ All three wire rope sizes DW1, DW2 and DW3 can be considered for use with both D-Clip parts. INSTALLATION INSTRUCTIONS ANCHORS & FASTENERS L W T L = 1.5", W = 1" , T = 1/4" Step 1 Pass the Loop End Wire Attachment through the opening of the D-Clip. Note: A loop created with a TOUGHLOCKTM device may also be used. Note: Must follow safety instructions for tools. Step 2 select and install an appropriate sized anchor through the D-Clip into the base material to the required minimum embedment. . Note: The two sides of the D-Clip should be compressed together when the anchor is fully installed. Note: refer to specific Anchor Installation Instructions TECHNICAL GUIDE CAbLE HANGErs ©2025 DEWALT rEV. A 2 CABLE HANGERS ANCHORS & FASTENERS PERFORMANCE DATA PERFORMANCE DATA Allowable Load Capacities for TOUGHWIRETM D-Clip Assemblies in Normal-Weight Concrete1,2,3,4,5,6,7,8 Minimum Concrete Compressive Strength = 3,000 psi Anchor Description Nominal Anchor Diameter (in.) Minimum Embedment Depth in. (mm) TOUGHWIRETM Size lbs. (kN) Mounting Orientation D-Clip with 5/16" Clearance Hole (Cat. No. DTWDCLIP025) DW1 40 (0.2) 40 (0.2) screw-bolt+TM Hex Washer Head 1/4" 1 (25) DW2 125 (0.6) 125 (0.6) DW3 300 (1.3) 300 (1.3) DW1 40 (0.2) 40 (0.2) spike® Mushroom Head 1/4" 1 (25) DW2 DW3 125 (0.6) 195 (0.9) 125 (0.6) 300 (1.3) 1-1/4 (31) DW3 275 (1.2) 300 (1.3) DW1 40 (0.2) 40 (0.2) Power-stud®+ sD1 1/4" 1-1/8 (28) DW2 125 (0.6) 125 (0.6) DW3 300 (1.3) 300 (1.3) DW1 40 (0.2) 40 (0.2) UltraCon® 1 (25) DW2 125 (0.6) 125 (0.6) Hex Washer Head / 5/16" TrimFit Hex Head DW3 185 (0.8) 300 (1.3) 1-3/4 (45) DW3 300 (1.3) 300 (1.3) D-Clip with 1/2" Clearance Hole (Cat. No. DTWDCLIP044) DW1 40 (0.2) 40 (0.2) screw-bolt+TM Hex Washer Head 3/8" 1-1/2 (38) DW2 125 (0.6) 125 (0.6) DW3 300 (1.3) 300 (1.3) DW1 40 (0.2) 40 (0.2) spike® Mushroom Head 3/8" 1-3/4 (45) DW2 125 (0.6) 125 (0.6) DW3 300 (1.3) 300 (1.3) DW1 40 (0.2) 40 (0.2) Power-stud®+ sD1 3/8" 1-5/8 (41) DW2 125 (0.6) 125 (0.6) DW3 300 (1.3) 300 (1.3) 1. Tabulated load values are for anchors installed in uncracked concrete. Concrete compressive strength must be at the minimum at the time of installation. 2. In unshaded cells, the capacity of the wire rope controls the failure in the assembly. 3. In shaded cells, the capacity of anchor in concrete controls the failure in the assembly. 4. Allowable capacities are based on a safety factor of 4.0. 5. The minimum base material thickness should 3-1/2 inches. 6. Tabulated data is based on a minimum spacing distance of 2-3/4 inches for 1/4" and 5/16" diameter anchors and a minimum spacing distance of 4 inches for 3/8" diameter anchors. 7. Tabulated data is based on a minimum edge distance of 3-1/2 inches. 8. Nominal anchor length must exceed the minimum embedment depth + 1/4 inch. TECHNICAL GUIDE CAbLE HANGErs ©2025 DEWALT rEV. A 3 CONDITIONS OF USE CONDITIONS OF USE ANCHORS & FASTENERS CABLE HANGERS Do not use in corrosive environments, e.g., chlorinated environments. For use in dry, interior locations only. ORDERING INFORMATION ALWAYs wear safety glasses when working with TOUGHWIrETM. D-Clip Cat. No. DTWDCLIP025 DTWDCLIP044 Description D-Clip for 1/4" Anchor/Fastener D-Clip for 3/8" Anchor/Fastener Clearance Hole Diameter (in.) 5/16" 1/2" Pack Qty. 50 50 Carton Qty. 300 300 TOUGHWIRETM Loop End Cat. No. TOUGHWIRETM Size DTW0106LE DW1 DTW0112LE DW1 DTW0120LE DW1 DTW0206LE DW2 DTW0212LE DW2 DTW0220LE DW2 DTW0235LE DW2 DTW0306LE DW3 DTW0312LE DW3 DTW0320LE DW3 DTW0335LE DW3 TOUGHWIRETM Cable Length (ft) 6 12 20 6 12 20 35 6 12 20 35 Pack Qty. 75 50 25 25 25 25 25 25 25 10 15 Carton Qty. 300 200 100 100 100 100 100 100 100 40 30 TOUGHLOCKTM Wire Locking Device Cat. No. TOUGHWIRETM Size DTWTOUGHLOCK01 DW1 DTWTOUGHLOCK02 DW2 DTWTOUGHLOCK03 DW3 Pack Qty. 100 50 25 Carton Qty. 1000 500 150 STRUTLOCKTM Wire Locking Devices Cat. No. TOUGHWIRETM Size DTWsTrUTLOCK02 DW2 DTWsTrUTLOCK03 DW3 Pack Qty. 15 10 Carton Qty. 90 60 ALWAYs wear safety gloves when working with TOUGHWIrETM. SQUARELOCKTM Wire Locking Device Cat. No. TOUGHWIRETM Size SQUARELOCKTM Device Without EPDM Gasket DTWsQLOCK02 DW2 DTWsQLOCK03 DW3 SQUARELOCKTM Device With EPDM Gasket DTWsQLOCKP02 DW2 DTWsQLOCKP03 DW3 Pack Qty. Carton Qty. 50 300 20 120 50 300 20 120 TOUGHWIRETM Cable Cutter Cat. No. Description DTWHANDCUTTEr Cutters for DW1, DW2 and DW3 TOUGHWIrETM Cable Pack Qty. 1 Carton Qty. 10 4 TECHNICAL GUIDE CAbLE HANGErs ©2025 DEWALT rEV. AAdobe PDF Library 17.0