User Manual for Infinix models including: ZERO 30 X6731B Smartphone, ZERO 30, X6731B Smartphone, Smartphone
INFINIX MOBILITY LIMITED X6731B 2AIZN-X6731B 2AIZNX6731B x6731b
File Info : application/pdf, 10 Pages, 242.82KB
DocumentDocumentInfinix ZERO 30 X6731B User Manual(A) Explosion diagram specification 1 OLED 2 VC 3 LCM FILM 4 MID FRAME 5 CCD 6 F CAM 7 SCREW M1.4*L3.5*D2.5*H0.5 8 SCREW M1.2*L2.0*D2.3*H0.5 9 UP SPEAK 10 MAIN CAM COPPER 11 2M CAM ADH 12 2M KH7 RUBBER 13 PS RUBBER 14 MAIN PCB 15 MAIN R CAM 16 RF LINE2 17 UP FRAME 18 FLASH FPC 19 RF LINE1 20 DECO PLATIC SUPI 21 NFC 22 BAT COVER 23 DECO AL 24 DECO GLASS 25 FLASH SHIELD 26 DECO FLASH SHIELD AL 27 DECO FLASH SHIELD AL ADH 28 FLASH SHIELD ADH 29 BOX 30 DOWN FRAME 31 ANT PCB 32 FINGGER PRINT 33 2M CAM WJ 34 SUB VIB 35 2M CAM XH 36 SUB PCB 37 VOL SIDEKEY 38 POWER SIDKEY 39 USB RUBBER 40 SIDKEY STEEL 41 OLED FPC RUBBER 42 CARD HOLDER 43 SIDKEY FPC 44 SIDKEY FRAME 1 45 BATTERY 47 MAIN FPC 46 SCREW M1.4*L3.5*D2.5*H0.5 48 USB MYLAR 2 Know your phone 1. Front camera 2. Volume + key 3. Volume - key 4. Power key 5. NFC 3 SIM card installation 1. Power off mobile. 2. Refer to the following picture for SIM card installation. 2 Charging the phone You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone). Use only INFINIX charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty. 3 FCC Caution Labelling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Information to user. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Note: This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. Specific Absorption Rate (SAR) information: This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through 4 periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6W/kg averaged over one gram of tissue. Device types: X6731B (FCC ID: 2AIZN-X6731B)has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use when properly worn on the body is 0.750 W/kg and for head is 0.788 W/kg. Simultaneous RF exposure is 1.124W/Kg. This device was tested for typical body-worn operations with the back of the handset kept 10mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that does not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. 5 For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved. Operating SystemAndroidTM Android is a trademark of Google LLC. 6