Installation Instructions

Record your model number: _________________________

Noter le numéro de modèle: _________________________

Anote su número de modelo: _________________________

Français, page 13

Español, página 25

Thank You for Choosing KOHLER

Need help? Contact our Customer Care Center.

• USA/Canada: 1-800-4KOHLER (1-800-456-4537) Mexico: 001-800-456-4537
• Hours of Operation: Monday-Friday 8:00 AM -5:00 PM (CT)
• Languages Spoken: English, Spanish, and translation services are available.
• Service parts: kohler.com/serviceparts
• Care and cleaning: kohler.com/clean
• Patents: kohlercompany.com/patents

Warranty

This product is covered under the KOHLER® Toilets and Seats Limited Warranty, found at kohler.com/warranty. For a hardcopy of warranty terms, contact the Customer Care Center.

Important Safeguards and Precautions

READ AND FOLLOW ALL INSTRUCTIONS

! WARNING: When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following:

DANGER: To reduce the risk of electrocution:

• Do not place or store this product where there is risk of falling or being pulled into a bath or sink.
• Do not place in or drop into water or other liquid.
• Do not reach for a product that has fallen into water. Unplug immediately.

! WARNING: To reduce the risk of burns, electrocution, fire, or injury to persons:

• Close supervision is necessary when this product is used by or near children, the elderly, or invalids. Adjust the temperature of the seat for the elderly, those who are incapacitated, or persons with sensitive skin.
• Use this product only for its intended use as described in this manual. Only use attachments recommended by Kohler Co.
• Never operate this product if there has been damage on the cord or plug. If the product is not working properly, has been dropped, damaged, or dropped into water, return for examination and repair.
• Keep the cord away from heated surfaces.
• Never use while sleeping or drowsy.
• Never drop or insert any object into any opening or hose.
• Do not use outdoors or where aerosol spray products are being used or where oxygen is administered.
• Connect this product to a properly grounded outlet only. See the “Grounding Instructions" section.

! CAUTION: Risk of product damage. Do not install this product in a location exposed to excessive moisture where condensation might form on the product surface. Provide adequate ventilation when bathing to avoid damage to the electronic components due to high humidity levels.

NOTE: The thermal protectors may trip during storage or transportation in warm weather causing the unit to not operate. Allow the unit to cool to room temperature before installation or operation.

Required Tools and Materials

[Image of wrench and screwdriver]

Before You Begin

! WARNING: Risk of electric shock, fire, or personal injury. Connect only to a nominal 120 VAC, 60 Hz circuit protected by a minimum 15 A Ground-Fault Circuit-Interrupter (GFCI)*.

! WARNING: Risk of electric shock. Do not immerse or flush the product with water.

! WARNING: Risk of product damage. Liquids can damage electronic components. Avoid spraying, soaking, or immersing the seat hinge.

IMPORTANT! The seat mounting holes on the toilet must be accessible from the underside of the bowl to accommodate the toilet seat cord. Some toilets, where the mounting holes are not accessible, will require an alternate mounting plate kit, 1362736 sold separately.

NOTICE: Do not use an extension cord with this product.

Follow all local plumbing, building, and electrical codes.

Turn OFF the water supply.

SAVE THESE INSTRUCTIONS

1. Install the Mounting Plate

[Diagram showing mounting plate installation with bolts and washers]

IMPORTANT! For toilets where the seat mounting holes are not accessible from the underside of the bowl, use kit 1362736 and refer to the "Install the Mounting Plate (Kit 1362736)" section.

• Route the cord through the mounting hole on the toilet.
• Position the mounting plate over the mounting holes.
• Position the washers in the mounting plate with the "+" oriented toward the toilet tank.
• Insert the bolts through the mounting plate and into the mounting holes.

2. Secure the Mounting Plate

[Diagram showing securing the mounting plate with nuts and a wrench]

• Attach the slotted nut onto the cord and slide up on the bolt.
• Slide the other nut up on the other bolt.
• Using a 7/16" wrench and screwdriver, tighten the bolts while holding the nuts in place.

3. Install the Mounting Plate (Kit 1362736)

[Diagram showing installation of mounting plate using kit 1362736]

NOTE: The following instructions are for toilets without access to the underside of the bowl. Kit 1362736 is required.

• Position the mounting plate over the mounting holes. Verify that the cord does not get pinched.
• Position the washers in the mounting plate with the "+" oriented toward the toilet tank.
• Insert the bolts through the mounting plate and thread into the mounting holes.
• Use a screwdriver to tighten the bolts.

4. Install the Seat

[Diagram showing alignment and clicking of the seat onto the mounting plate]

• Align the holes in the seat hinge over the posts on the mounting plate.
• Press the seat down to click in place.

Seat Removal

• Lift the lid and seat to the vertical position.
• Press the side buttons and lift the seat off the mounting plate.

Seat Adjustment (If Needed)

• Remove the seat from the mounting plate.
• Loosen the bolts, and rotate the washers.
• Retighten the bolts.
• Reinstall the seat to the mounting plate.

5. Complete the Installation

[Diagram showing power cord connection to the toilet seat and electrical outlet]

WARNING: Risk of electric shock, fire, or personal injury. Connect only to a nominal 120 VAC, 60 Hz circuit protected by a minimum 15 A Ground-Fault Circuit-Interrupter (GFCI)*.

• If not already installed, install an electrical outlet within 4' (1219 mm) of the toilet.
• Thread the power supply cord onto the toilet seat cord. Tighten the barrel.
• Plug the power supply into the electrical outlet.
• To begin using this product, refer to the quick start guide.

Range and Function Disclaimer

BLUETOOTH® is the name for a short-range radio frequency (RF) technology that operates at 2.4 GHz. The effective range of most BLUETOOTH portable devices is 10 meters. BLUETOOTH is designed for very low power use. The compatibility of the BLUETOOTH amplifier interface to portable devices differs according to the various individual devices and, in particular, may vary with different software versions for a device. The normal portable device BLUETOOTH range can be up to 10 meters, however, placement of your portable device and the BLUETOOTH amplifier's installation environment will impact your reception range.

Water and walls can act as blocking agents to the BLUETOOTH signal that your portable device is using to broadcast to your BLUETOOTH amplifier. Therefore, selecting an installation location that removes these range blocking obstacles will increase the effective range and performance of your BLUETOOTH amplifier.

You can test your BLUETOOTH reception by performing simple range tests using your portable device prior to performing a permanent installation. The best way to make use of the short BLUETOOTH range is to verify that your BLUETOOTH amplifier is as close to the BLUETOOTH transmitter (cell phone, tablet, etc.) as possible. The less distance between the two devices, the greater will be the reliability of your BLUETOOTH audio signal. The less distance means fewer obstacles in the medium through which the transmission is passing, so there is a reduced chance of audio signal loss.

The compatibility of the BLUETOOTH amplifier to portable devices differs according to the various individual devices and, in particular, may vary with different software versions for a device. All functions are based on industry-wide communications standards. Compatibility between the BLUETOOTH amplifier and portable device is therefore largely dependent upon the software version of the portable device. Other factors (for example, installation location, walls, distance) mean that in individual cases, sporadic impairment of functions may occur in devices that otherwise function reliably. Not all functions are supported in all countries.

Because of these reasons, Kohler Co. can assume no guarantee for the unlimited compatibility and functionality of your portable device with the BLUETOOTH amplifier.

The BLUETOOTH® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Kohler Co. is under license. Other trademarks and trade names are those of their respective owners.

Compliance

FCC ID: N82-KOHLER023

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, interference may occur in a particular installation. If this equipment causes harmful interference to radio or television reception, the user can troubleshoot by turning the equipment off and on, or by trying one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement

This portable transmitter with its antenna complies with FCC's RF exposure limits for general population/uncontrolled exposure.

This device must not be colocated or operated with any other antenna or transmitter.

CANADA IC: 4554A-KOHLER023

This device contains license exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's license exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.