TÜV Rheinland Test Report - Products

Prüfbericht - CN251MER 001

Test Report No.: 1288983

Client Reference No.: IKEA of Sweden AB

Client: Box 702, SE-343 81 Älmhult, Sweden

Test Item: Self-ballasted LED lamps

Identification / Type No.: LED2407G8NA

Order Content: TÜV Rheinland EMC service

Test Specification: FCC 47 CFR Part 15, Subpart B:2023 Class B, ICES-005:2018

Date of Sample Receipt: 2025-03-06

Test Laboratory: TÜV Rheinland (Shanghai) Co., Ltd.

Test Result: Pass ✔️

Issue Date: 2025-05-11

FCC ID: FHO-LED2407G8NA

Remarks

1. Test Equipment Calibration: All test equipment used during the specified testing period was calibrated according to the laboratory's calibration program and meets relevant standards. Traceability is ensured by the management system.

2. Digital Signature: This document is digitally signed. Verification of legal requirements is the user's responsibility. Information on verifying document authenticity is available at go.tuv.com/digital-signature.

3. Subcontracted Clauses: Test clauses marked with * were subcontracted. Deviations from specifications are listed in the report.

4. Conformity Decision Rule: Compliance is determined by comparing measurement results directly with limits, without considering measurement uncertainty, based on the 'Zero Guard Band Rule' and 'Simple Acceptance' (ILAC G8:2019, IEC Guide 115:2021).

General Product Information

Product Function and Intended Use: The Equipment Under Test (EUT) is a self-ballasted LED lamp with wireless dimming functionality for lighting and similar applications.

Ratings and System Details:

Rated Input: AC 120 V, 60 Hz, 79 mA
Rated Power: 8.1 W
RF IC: SiMG301

Independent Operation Modes: Basic modes are 'ON' and 'OFF' with dimming. Test modes included four variations of warm and white lighting with maximum and minimum output.

Highest Frequency: The highest frequency used in the EUT is 2480 MHz (for the wireless module).

Test Set-up and Operation Modes

Configuration Selection: The EUT was configured to measure its highest possible emission level. Tests were conducted on 2025-04-11 (Conducted Emission) and 2025-04-10 to 2025-04-14 (Radiated Emission).

Equipment and Cable Arrangement:

Conducted Emission: A block diagram shows the setup including the EUT, LISN, EMI receiver, computer, transformer, and power supply.
Radiated Emission (30 MHz - 1000 MHz): A diagram illustrates the setup with the EUT on a turntable, an antenna, and measurement equipment.
Radiated Emission (1 GHz - 18 GHz): A diagram shows the setup with the EUT, turntable, absorbers, and antenna.

Test Software: The 'Home' APP for iPhone was used.

Auxiliary Equipment: iPhone 15 (Apple), HomePod mini (Apple), E2489 Remote Control (IKEA).

EMC Compliance Measures: No special countermeasures were employed.

Conformity Decision Rule

For all EMI tests, compliance is determined by comparing measurement results directly with limits, as measurement uncertainties are less than specified values (UCISPR in CISPR 16-4-2).

Test Results - Emission

Conducted Emission (0.15 MHz - 30 MHz): The EUT was tested for conducted emissions according to FCC 47 CFR Part 15, Subpart B:2023, ICES-005:2018, ANSI C63.4-2014, and CISPR 16-2-1. Tests were performed in a shielded room with AC 120 V, 60 Hz input. The EUT passed all conducted emission tests across the specified operational modes. The minimum margin observed was 4.88 dB.

Radiated Emission (30 MHz - 1000 MHz): Radiated emissions were measured in a semi-anechoic chamber at a distance of 3 meters, according to FCC 47 CFR Part 15, Subpart B:2023, ICES-005:2018, ANSI C63.4-2014, and CISPR 16-2-3. The EUT was tested in Class B mode. The EUT passed all radiated emission tests. The minimum margin observed was 18.5 dB.

Radiated Emission (1 GHz - 18 GHz): Radiated emissions were measured in an absorber-lined semi-anechoic chamber at a distance of 3 meters, according to FCC 47 CFR Part 15, Subpart B:2023, ICES-005:2018, ANSI C63.4-2014, and CISPR 16-2-3. The EUT was tested in Class B mode. The EUT passed all radiated emission tests. The minimum margin observed was 16.7 dB.

List of Test and Measurement Instruments

The following key instruments were used for testing:

EMI Measurement Software: Rohde & Schwarz (EMC32-E+)
EMI Test Receivers: Rohde & Schwarz (ESR3, ESCI)
Thermohygrometers: testo (608-H1)
Artificial Mains Network: Rohde & Schwarz (ENV432)
Broadband Antenna: Schwarzbeck (VULB 9168)
Spectrum Analyzer: Rohde & Schwarz (FSV40)
Semi-anechoic Chamber: Frankonia (SAC3)

Detailed calibration dates and instrument serial numbers are available in the full report.

Photographs of the Test Set-Up

Refer to the test setup file for photographs.

	IKEA of Sweden AB Authorization to Act as Agent for FCC Certification Official authorization letter from IKEA of Sweden AB appointing TÜV Rheinland as agent for equipment certification, including statements on FCC compliance and federal benefits.
	IKEA Attestation Statement: Not Covered Entity Applicant for FCC Filing - FHO-LED2407G8NA This document is an attestation statement from IKEA of Sweden AB, filed with the Federal Communications Commission (FCC). It confirms that IKEA is a 'Not Covered Entity Applicant' for the product identified by FCC ID FHO-LED2407G8NA, which is a self-ballasted LED lamp. The statement is dated 2025.2.26 and signed by Ivan Susak, RA engineering manager.
	IKEA LED2407G8NA RF Exposure Compliance Report Report detailing the Radio Frequency (RF) exposure compliance for the IKEA LED2407G8NA self-ballasted LED lamps, including FCC and IC test results and calculations.
	IKEA FHO-LED2407G8NA Attestation Statement for Not Covered Equipment Attestation statement from IKEA of Sweden AB for the FHO-LED2407G8NA, confirming it is not covered equipment as per FCC rules.
	IKEA U.S. Agent Designation for Service of Process - FCC Certification Official designation of Go Global Compliance, Inc. as the U.S. Agent for Service of Process for IKEA of Sweden AB, related to FCC certification for the FHO-LED2407G8NA product.
	TÜV Rheinland Test Report: IKEA LED Lamp (Model LED2407G8NA) This TÜV Rheinland test report details the compliance testing of IKEA's self-ballasted LED lamps, model LED2407G8NA, for RF characteristics, including conducted and radiated emissions, bandwidth, and output power, adhering to FCC and RSS standards.
	IKEA LED2407G8NA E26 NA Product Marking and Specifications Detailed product marking information for the IKEA LED2407G8NA E26 NA LED lamp, including technical specifications, safety warnings, and identification codes.
	TÜV Rheinland Test Report: IKEA LED2407G8NA Self-ballasted LED Lamps This TÜV Rheinland test report details the compliance testing for IKEA's LED2407G8NA self-ballasted LED lamps, covering RF characteristics, conducted emissions, and radiated emissions according to FCC and RSS standards.