RYOBI RYI300BG 40 Volt Power Source

Operator's Manual

IMPORTANT SAFETY INSTRUCTIONS

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for power source model RYI300BG.
For use with RYOBI 40 V battery packs, see tool/appliance/ battery pack/charger correlation supplement 988000-842.
Do not expose the power source to rain or wet conditions. Water entering the power source will increase the risk of electric shock.
Do not use the power source if it has been dropped or received a sharp blow. A damaged power source will increase the risk of fire.
Remove the battery pack from the power source when not in use.
This product is for indoor use only.
Do not disassemble the power source.
To reduce the risk of injury, close supervision is necessary when an appliance is used near children.
Store power source indoors and away from children.
As with all electrical devices, use caution when plugging/unplugging other devices into this unit. Do not force plugs into this unit.
If this unit is used in a manner not specified by the manufacturer, the protection provided by this equipment may be impaired.
Do not overload the power source. It must be used for powering devices less than the product rating.
Two- or three-prong plugs may be used with this product. Do not force a polarized plug (one prong larger than the other) into this product. Flip plug over and retry.
Never block air vents. Blocked vents may cause overheating. Power source will automatically shut off AC output when overheated.
Keep power source cool. Do not place near heat vents or in direct sunlight.
Do not use the power source around flammable fumes and gasses, such as in the bilge of a boat or near propane tanks.
Do not put foreign objects into the power source.
Operate this product using only the AC power type listed in the product specifications.
This unit should never be hard wired into a circuit.
Do not power life support devices or other necessary medical equipment with this power source.
Save these instructions. Refer to them frequently and use them to instruct others who may use this product. If you loan someone this product, loan them these instructions also.

PRODUCT SPECIFICATIONS

Specification	Value
Watts	300 Watts Continuous
DC Input	40 Volts DC
AC Output	120 Volts, 2.5 Amps
USB Output*: USB-A	5/9/12 Volts, up to 18 Watts
USB Output*: USB-C	5/9/12/15/20 Volts, up to 40 Watts
Output Wave Form	Pure Sine Wave

*USB ports share internal circuitry. If USB-A is in use, USB-C will supply 5V output only.

OPERATION

APPLICATIONS

Operating and charging USB-powered devices
Supplying electrical power for operating compatible small electronics such as cell phones, tablets, laptops, LED lights, small fans, radios, etc.
Providing a directed task light to illuminate a small area

NOTE: This device is not compatible for use with appliances, power tools, air conditioners, sump pumps, compressors, and/or other larger electrical devices.

INSTALLING/REMOVING BATTERY PACK

See Figure 1.

To install: insert a battery pack into the power source as shown. Make sure the latch on the battery pack snaps into place and the battery pack is secured in the power source before beginning operation.
To remove: depress the latch on the battery pack.

Figure 1 Description

Figure 1 shows the RYOBI 40V Power Source. Label A indicates the battery pack (not included). Label B points to the latch used to release the battery pack. Label C highlights the LED task light. Label D indicates the light button. Label E indicates the power button. Label F points to the USB charging ports. Label G indicates the 120V receptacle.

USING THE POWER SOURCE

See Figures 1 - 2.

When a charged battery pack is installed, this power source converts DC electricity to 120V AC household power and/or USB-A (5/9/12V, up to 18 W) or USB-C (5/9/12/20V, up to 40 W) charging power, allowing the user to charge and power a variety of devices.

WARNING:

Risk of electric shock. When using a grounded appliance this tool will not provide an electrical path to earth ground. Do not power devices with damaged or frayed power cords.

Insert a battery pack into the power source.
Press and hold the power button [Power Button] for 1.5 seconds to turn the power source on. The LED will light up green when ready to use.
Plug devices you want to power or charge into the power source's USB ports and/or 120 volt receptacle.
If the power button LED blinks red, the power source may be overloaded. Disconnect your device, make sure your battery pack is sufficiently charged to power your device, then press the button to reset the power source. Reconnect your device and try again. If the fault condition immediately reoccurs, the item being powered exceeds the capacity of the power source.
If the power button LED turns solid red, the power source is overheated. Allow the unit to cool until the LED blinks red, then press the button to reset the power source.
If the power button LED blinks yellow, the battery pack is low and needs to be recharged.

To use the task light, press the light button [Light Button]. A second press will cause the light to strobe. Press again to turn the light off.

NOTE: The power source must be on for the worklight to function.

When finished, disconnect your device and press and hold the power button indicator [Power Button] for 1.5 seconds to turn off the power source.

NOTE: When needed, an internal cooling fan will run to regulate the unit's operating temperature. If running, always wait for the fan to stop before you disconnect the battery pack from the power source.

Figure 2 Description

Figure 2 illustrates the usage of the power source. Label A points to the 120V receptacle. Label B shows an AC product being powered (not provided). Label C indicates the USB-A port. Label D indicates the USB-C port. Label E shows a USB product being charged (not provided).

WARRANTY

This product has a Five-year Limited Warranty for personal, family, or household use (90 days for business or commercial use). For warranty details, visit www.ryobitools.com or call (toll free) 1-800-525-2579.

Model/item number on product may have additional letters at the end. These letters designate manufacturing information and should be provided when calling for service.

Manufacturer Information

TECHTRONIC INDUSTRIES POWER EQUIPMENT
P.O. Box 1288, Anderson, SC 29622, USA

	Ryobi RYi1030A 1000W Auto Power Inverter Operator's Manual Comprehensive operator's manual for the Ryobi RYi1030A 1000W Auto Power Inverter. Provides essential safety instructions, detailed product specifications, step-by-step operating procedures, maintenance guidelines, and warranty information for converting DC power to AC household power for various applications.
	RYOBI 40V Power Station RYi1802BTVNM/RYi1802B6VNM Replacement Parts List and Wiring Diagram This document provides a comprehensive replacement parts list and wiring diagram for the RYOBI 40V Power Station models RYi1802BTVNM and RYi1802B6VNM. It includes detailed part numbers, descriptions, quantities, and a visual representation of the internal components and their connections.
	RYOBI 40V Leaf Vacuum Operator's Manual - RY40405 Essential operator's manual for the RYOBI 40V Leaf Vacuum (RY40405), covering safety, assembly, operation, and maintenance for effective product use.
	Ryobi 40V Lithium-Ion Battery Pack Technical Data Sheet Technical data sheet for the Ryobi 40V Lithium-Ion Battery Pack, including product identification, hazard identification, first aid measures, fire fighting measures, accidental release measures, handling and storage, exposure controls, physical and chemical properties, stability and reactivity, toxicology, ecological information, disposal considerations, transportation information, and regulatory information.
	RYOBI RY401018 40V 20-Inch Lawn Mower Operator's Manual Comprehensive operator's manual for the RYOBI RY401018 20-inch 40V lawn mower. Includes safety instructions, assembly, operation, maintenance, and troubleshooting guides for optimal performance and safe use.
	Ryobi RY3112FW Flexible Wand Operator's Manual and Instructions Operator's manual for the Ryobi RY3112FW flexible wand attachment for power cleaners. Includes safety warnings, applications, and connection instructions.
	RYi150BG 18V Power Source Operator's Manual This manual provides important safety and operating instructions for the RYi150BG 18V Power Source. Learn about product specifications, applications, installation, operation, and warranty information.
	RYOBI RY14122 Electric Pressure Washer Operator's Manual Comprehensive operator's manual for the RYOBI RY14122 Electric Pressure Washer, covering safety instructions, assembly, operation, maintenance, and troubleshooting.