Latitude Run Dining Set Assembly Instructions
Item Numbers: N717P336673 (Dining Table), N717P336674 (Dining Chair)
General Assembly Information
Please read these instructions fully before starting assembly.
- Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid scratching the parts.
- Kindly follow the assembly instructions step by step.
- Do not tighten all screws and bolts until the table is fully assembled.
- Unscrew the protective plastic supports from the metal insert of the table legs before assembly.
- Assembly will be easier with 2 people.
Care and Maintenance
Only clean using a damp cloth and mild detergent. Do not use bleach or abrasive cleaners.
Dining Table Assembly (Item NO.N717P336673)
Part List
A: TABLE TOP BETWEEN (1 pc)
B: TABLE TOP SIDE (1 pc)
C: PANEL TOP LEG (2 pcs)
D: LEG (2 pcs)
E: LEG (2 pcs)
Hardware List
1: BOLT Ø 5/16" x 40 mm (18 pcs)
2: LOCK WASHER Ø5/16" x 13 mm (18 pcs)
3: FLAT WASHER Ø5/16" x 19 x 2 mm (18 pcs)
4: ALLEN KEY 4 mm (1 pc)
5: WOOD SCREWS Ø4 x 15 mm (16 pcs)
6: HEIGHT ADJUSTER Ø8x 20 mm (8 pcs)
7: PATCH 65 x 55 x 3 mm (4 pcs)
Assembly Steps
Step 1
This step involves assembling the base of the table. Two leg assemblies are formed, each using two legs (D, E) and a panel top leg (C). Height adjusters (6) are screwed into the bottom of each leg (D, E). The panel top leg (C) is attached to the legs (D, E) using wood screws (5). The diagram indicates this process is done 4 times for each leg assembly.
Diagram Description: Two leg assemblies are shown. Each consists of two legs (D, E) connected by a panel (C). Height adjusters (6) are shown being inserted into the bottom of the legs. Wood screws (5) are used to attach panel (C) to legs (D, E).
Step 2
The two assembled leg structures are now attached to the underside of the table top components (A and B). Bolts (1) are passed through flat washers (3) and lock washers (2) before being inserted into the corresponding holes. An Allen key (4) is used for tightening. The diagram shows this connection is made 5 times.
Diagram Description: The two leg assemblies are shown being attached to the underside of the table top sections (A and B). Bolts (1) pass through flat washers (3) and lock washers (2) before entering the pre-drilled holes. An Allen key (4) is shown for tightening.
Step 3
This step focuses on completing the table top and final assembly. The remaining table top sections (A, B) are secured to the leg structures. Bolts (1), lock washers (2), and flat washers (3) are used for these connections, with the diagram indicating 8x repetition. A final illustration shows the fully assembled dining table.
Diagram Description: This step shows the final attachment of the table top sections (A, B) to the leg structures. Bolts (1), lock washers (2), and flat washers (3) are used. The diagram indicates 8x repetition for these connections. A final image shows the completed dining table.
Dining Chair Assembly (Item NO.N717P336674)
Part List
A: BACK FRAME (4 pcs)
B: SEAT FRAME (4 pcs)
C: LEG (8 pcs)
Hardware List
1: BOLT Ø 1/4" x 40 mm (8 pcs)
2: BOLT Ø 1/4" x 55 mm (16 pcs)
3: BOLT Ø 1/4" x 75 mm (16 pcs)
4: LOCK WASHER Ø5/16" x 13 mm (40 pcs)
5: FLAT WASHER Ø5/16" x 19 x 2 mm (40 pcs)
6: ALLEN KEY 4 mm (1 pc)
Assembly Steps
Step 1
The assembly begins by attaching the legs (C) to the seat frame (B) using bolts (2), lock washers (4), and flat washers (5). Subsequently, the back frame (A) is attached to the seat frame (B) using bolts (1), lock washers (4), and flat washers (5). The diagram shows this is done twice for the legs and twice for the back frame attachment.
Diagram Description: This step shows the attachment of legs (C) to the seat frame (B) using bolts (2), lock washers (4), and flat washers (5). It also shows the attachment of the back frame (A) to the seat frame (B) using bolts (1), lock washers (4), and flat washers (5). An Allen key (6) is shown.
Step 2
This step completes the chair assembly. The diagram shows the final tightening of all bolts and connections, ensuring the chair is stable. Bolts (2), lock washers (4), and flat washers (5) are used to secure the seat frame (B) to the legs (C) and back frame (A). An Allen key (6) is provided for this purpose.
Diagram Description: This step shows the final tightening of bolts and assembly of the chair. It uses bolts (2), lock washers (4), and flat washers (5) to secure the seat frame (B) to the legs (C) and back frame (A). An Allen key (6) is shown.
