CLICK Stackable I/O Module Specifications
Model: C0-04DA-2
Part Number: C0-04DA-2
Price Code: $00c8h
4-Channel Analog Voltage Output Module
This module provides 4-channel analog voltage output with a 12-bit resolution. The output range is 0-10V. It requires external 24VDC power and includes a removable terminal block (AutomationDirect p/n C0-8TB).
Wiring Diagram
The diagram shows the C0-04DA-2 module with connections for CH1, CH2, CH3, and CH4 outputs. Each channel has a load connected. The 'OV' terminals are internally connected. The diagram also illustrates the 24VDC power supply input (+24V and OV).
Output Specifications
| Specification | Value |
|---|---|
| Outputs per Module | 4 |
| Output Range | 0-10 V |
| Resolution | 12-bit, 2.44 mV per count |
| Output Type | Voltage sourcing at 10mA max. (1 common) |
| Output Value in Program Mode | Determined by CPU |
| Output Value in Fault Mode | 0 V |
| Output Impedance | 0.2 Ω typical |
| Load Impedance | >1000Ω |
| Maximum Capacitive Load | 0.01 uF maximum |
| Allowed Load Type | Grounded |
| Maximum Inaccuracy | 0.5% of range |
| Max. Full Scale Calibration Error (Not including Offset) | ±0.2% of range maximum voltage |
| Max. Offset Calibration Error | ±0.2% of range maximum |
| Accuracy vs. Temperature | +75 PPM/°C maximum full scale calibration change (±0.0025% of range/°C) |
| Max. Crosstalk at DC, 50/60Hz | -72 dB, 1 LSB |
| Linearity Error (End to End) | +4 LSB max., (±0.1% of full scale); monotonic with no missing codes |
| Output Stability and Repeatability | ±2% LSB after 10 minute warmup period typical |
| Output Ripple | 0.1% of full scale |
| Output Settling Time | 0.3 ms maximum, 5us minimum (full scale range) |
| All Channel Update Rate | 10ms |
| Max. Continuous Overload | Outputs current limited to 40mA typical; continuous overloads on multiple outputs can damage module. |
| Field to Logic Side Isolation | 1800 VAC applied for 1 second (100% tested) |
| Type of Output Protection | 0.1 µF transient suppressor |
| Output Signal at Power Up and Power Down | 0 V |
| External 24VDC Power Required | 85mA |
| Base Power Required (24VDC) | 20mA |
| Terminal Block Replacement | Automation Direct p/n C0-8TB |
| Drawing Link | |
| Weight | 2.9 oz [82g] |
ZIPLink Pre-Wired PLC Connection Cables and Modules for CLICK PLC
AutomationDirect offers ZIPLink solutions for simplified wiring. These include pre-wired cables and DIN rail mount connector modules that reduce installation time and complexity.
- 11-pin connector cable: ZL-CO-CBL11 (0.5 m length), ZL-CO-CBL11-1 (1.0 m length), ZL-CO-CBL11-2 (2.0 m length)
- ZL-RTB20 20-pin feed-through connector module
The image shows examples of ZIPLink cables and a feed-through connector module.
Important Note
NOTE: When using this module, you must also use CLICK programming software and PLC firmware version V1.40 or later.
General Specifications for All CLICK Stackable I/O Modules
These general specifications apply to all CLICK Stackable I/O Modules. Refer to the appropriate I/O temperature derating charts for specific operating conditions based on your application's ambient temperature.
| Specification | Value |
|---|---|
| Operating Temperature | Analog, analog combo I/O modules only: 32°F to 140°F [0°C to 60°C]; All other modules: 32°F to 131°F [0°C to 55°C] |
| Storage Temperature | -4°F to 158°F [-20°C to 70°C] |
| Ambient Humidity | 30% to 95% relative humidity (non-condensing) |
| Environmental Air | No corrosive gases. Environmental pollution level is 2 (UL840) |
| Vibration | All other modules: IEC60068-2-6 (Test Fc) |
| Shock | MIL STD 810C, Method 516.2, IEC60068-2-27, JIS C60068-2-27, Category [f], Procedure [VIII] |
| Noise Immunity | EN61131-2, EN61000-4-2 (ESD), EN61000-4-3 (RFI), EN61000-4-4 (FTB), EN61000-4-5 (Surge), EN61000-4-6 (Conducted), EN61000-4-8 (Power frequency magnetic field immunity) |
| Emissions | EN55011:1998 Class A; EN61000-6-4:2007+A1:2011 |
| Agency Approvals | UL508, UL61010-2-201 (File No. E157382); CE (EN61131-2); CUL Canadian C22.2 |
| Other | RoHS 2011/65/EU Amendment (EU)2015/863 |
NOTE: These modules are available to use with CLICK or CLICK PLUS systems.
