Kuzco Lighting
Instruction Manual for Kuzco Lighting models including: PD87736 Ceiling LED Pendant, PD87736, Ceiling LED Pendant, LED Pendant
Cerchio PD87736 – Kuzco Lighting
PD87736-WH - Kuzco Lighting - LED Pendant - Cerchio | EverLights
File Info : application/pdf, 2 Pages, 878.54KB
DocumentDocumentCeiling LED Pendant PD87736 INSTALLATION SHEET START FROM HERE · Make sure POWER is COMPLETELY OFF at the fuse box · Have your fixture installed by a qualified licensed electrician · Prepare everything in a clear area · Wear gloves at all time during this installation · Read instructions carefully before you start assembly · Keep this installation sheet for future reference Technical Support: 1-855-855-8926 Please Note: · This Kuzco LED fixture comes with pre-wired LED module(s) · Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary contact with the module could cause permanent damage · Use ELV (Electronic Low Voltage) or TRIAC type of dimmer for dimming application · 120V input 1. Remove fixture from its original package 2. Separate mounting plate (1c) from canopy (2a) by removing canopy screws (2b) 3. Attach mounting plate (1c) to electrical junction box (1a) using junction box screws provided (1e) in hardware package 4. Secure mounting plate (1c) to mounting surface with anchors (1f) and screws (1g) 5. To change fixture height, push and hold wire gripper (2g), slide wire to desired length and then release wire gripper (2g) to secure 6. Make proper electrical connections (black to hot "L", white to neutral "N", ground to "GND") with wire nuts (1b) provided in hardware package 7. Attach canopy (2a) to mounting plate (1c) with canopy screws (2b) 8. Fine tone wire length if necessary, by push and hold wire gripper (2g) and then adjust wire to desired length 1a. 1f. 1b. 1c. 1e. 1g. 2b. 2a. 2g. 19054 28th Avenue Surrey, BC Canada V3Z 6M3 T: 604 538 7162 TF: 1-855 85 KUZCO F: 604 538 7196 W: kuzcolighting.com 20220520 Page 1 of 2 Ceiling LED Pendant PD87736 INSTALLATION SHEET START FROM HERE · Make sure POWER is COMPLETELY OFF at the fuse box · Have your fixture installed by a qualified licensed electrician · Prepare everything in a clear area · Wear gloves at all time during this installation · Read instructions carefully before you start assembly · Keep this installation sheet for future reference Please Note: · This Kuzco LED fixture comes with pre-wired LED module(s) · Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary contact with the module could cause permanent damage · Use ELV (Electronic Low Voltage) or TRIAC type of dimmer for dimming application · 120V input Technical Support: 1-855-855-8926 FOR ALTERNATIVE SIDE CANOPY INSTALL 1. Disconnect output wires on driver (4a) 2. Separate wire gripper (2g) from canopy (2a) by removing nut and tooth washer (6a). Separate plug (6b) from canopy (2a) by removing nut, tooth washer and flat washer (6c) (See Illustration 1) Ground Wire 6a. Illustration 1 Ground Wire 6c. 2a. Illustration 2 5a. 3. Feed fixture wires through centre hole on canopy plate (7a), canopy (2a), tooth washer and nut (5a). Attach 2a. canopy plate (7a) to canopy (2a), followed by wire gripper (2g) and secure with tooth washer and nut (5a) (See 6b. 7a. Illustration 2) 2g. 4. Make proper electrical connections between LED and DC 2g. driver, LED- Negative, LED+ Positive using wago connector (4b) provided (See Illustration 3 and refer to diagram on driver) 5. Make proper electrical connections (black to hot "L", white to neutral "N", ground to "GND") with wire nuts 1a. (1b) provided in hardware package 1b. 6. Attach canopy (2a) to mounting plate (1c) with canopy 1c. screws (2b). Position desired amount of wire by pushing gripper (2g) on canopy 7. Pull wire through aircraft barrel (3b) and stopper (3d). Secure aircraft barrel (3b) to mounting surface with anchor 1e. 4a. (3c) and screw (3a). Adjust wire to desired length and 4b. secure with set screw (3e). Insert wire gripper (2g) into aircraft barrel (3b) to close 8. Fine tone wire length if necessary, by push and hold wire gripper (2g) and then adjust wire to desired length 2b. 2a. Illustration 3 LN DC Driver + - Low Voltage 3c. 3e. 3d. 3b. 3a. 2g. 7a. Note: Ideal distance of wire grippers from canopy is 26-3/16" and 30-3/16" 2g. 26-3/16" 30-3/16" 19054 28th Avenue Surrey, BC Canada V3Z 6M3 T: 604 538 7162 TF: 1-855 85 KUZCO F: 604 538 7196 W: kuzcolighting.com 20220520 Page 2 of 2