ARB 4x4 Accessories Australia - Your Partner In Adventure
Instructions for ARB models including: 4480010 Bronco Rock Sliders, 4480010, Bronco Rock Sliders, Rock Sliders, Sliders
Ford Bronco Rock Sliders by ARB | Bronco6G - 2021 Ford Bronco & Bronco Raptor Forum, News, Blog & Owners Community
File Info : application/pdf, 8 Pages, 1.13MB
DocumentDocumentPart Number: Product Description: Suited to vehicle/s: 4480010 ROCK SLIDERS 2021 FORD BRONCO WARNING NOTE THE FOLLOWING: This product must be installed exactly as per these instructions using only the hardware supplied. Do not use this product for any vehicle make or model, other than those specified by ARB. This product or its fixing must not be modified in any way. The installation of this product may require the use of specialized tools and/or techniques It is recommended that this product is only installed by trained personnel These instructions are correct as at the publication date. ARB Corporation Ltd. cannot be held responsible for the impact of any changes subsequently made by the vehicle manufacturer During installation, it is the duty of the installer to check correct operation/clearances of all components Work safely at all times Unless otherwise instructed, tighten fasteners to specified torque ARB 4x4 ACCESSORIES Corporate Head Office 42-44 Garden St Kilsyth, Victoria AUSTRALIA 3137 Australian enquiries North & South American enquiries Other international enquiries Tel: +61 (3) 9761 6622 Fax: +61 (3) 9761 6807 sales@arb.com.au sales@arbusa.com exports@arb.com.au www.arb.com.au Last Rev Date: 03/03/2022 Page 1 of 8 Fitting instructions# 37801067 Copyright © 2021 by ARB Corporation Limited. All rights reserved, this document must not be reproduced without the express authority of ARB Corporation Ltd GENERAL CARE AND MAINTENANCE By choosing an ARB Rock Slider, you have bought a product that is one of the most sought after 4WD products in the world. Your Rock Slider is a properly engineered, reliable, quality accessory that represents excellent value. To keep your Rock Slider in original condition it is important to care and maintain it following these recommendations: It is recommended that following exposure to salt, mud, sand or other contaminants exposed surfaces should be thoroughly cleaned with wash and wax type suds solution. As part of any Pre Trip Preparation, or on an annual basis, it is recommended that a thorough visual inspection of the step and rail and surrounding components is carried out, making sure that all bolts are torqued to the correct specification. Also check that nearby wiring and plumbing are free of damage. Replace any components as necessary. This service can be performed by your local authorized ARB Stockist. REQUIRED TOOLS FOR FITMENT OF PRODUCT: METRIC SOCKET SET ALLEN KEY SET TORQUE WRENCH 9-77Nm PROTECTIVE FILM IMPACT WRENCH LIFT TABLE ANGLED WRENCH HAVE AVAILABLE THESE SAFETY ITEMS WHEN FITTING PRODUCT: Protective eyewear Hearing protection NOTE: `WARNING' notes in the fitting procedure relate to OHS situations, where to avoid a potentially hazardous situation it is suggested that protective safety gear be worn or a safe work procedure be employed. If these notes and warnings are not heeded, injury may result. FASTENER TORQUE SETTINGS: SIZE Torque Nm Torque lbft M6 9Nm 7lbft M8 22Nm 16lbft M10 44Nm 32lbft M12 77Nm 57lbft Last Rev Date: 03/03/2022 Page 2 of 8 Fitting instructions# 37801067 Copyright © 2021 by ARB Corporation Limited. All rights reserved, this document must not be reproduced without the express authority of ARB Corporation Ltd APPLICATION. FITTING KIT BOXED FITTING KIT BAGGED PARTS LISTING PART NO. QTY 4655122 1 4655123 1 3195081 6 4581011 14 4584377 4 6151046 1 6151207 1 6151255 10 6151377 2 6151553 1 6151574 4 6151428 4 6151596 1 6151715 1 665051 2 6821178 8 DESCRIPTION WELD ASM ROCK-S LH SUIT BRONCO WELD ASM ROCK-S RH SUIT BRONCO NUT PLATE ASSY M12x1.75 600mm WASHER FLAT M12x27x4 | ZP WASHER FLAT M12x30x5 | ZNS480 WASHER FLAT M6 | ZNS480 BOLT HXHD M6x1.0x25 | PC8.8 TZP480 SCREW HXHD M12x1.75x40 | PC8.8 ZP BOLT U M12x1.75x(175x120) | PC8.8 TZP NUT CAGED M8 3.3-4.7 PC8.8 BTZP480 1238-C NUT HEX NYLOC M12x1.75 | TZP480 NUT FLANGE M12x1.75 | PC8.8 SERRATED P CLIP 19MM NUT CAGED M6 3.6-4.5 | 836-D TAPE RIB WINDOW @ 500MM CABLE TIE4.8 X 200MM Last Rev Date: 03/03/2022 Page 3 of 8 Fitting instructions# 37801067 Copyright © 2021 by ARB Corporation Limited. All rights reserved, this document must not be reproduced without the express authority of ARB Corporation Ltd FITTING PROCEDURE IMPORTANT NOTE: These instructions apply to FORD BRONCO. 1. If fitted, remove the factory side steps. 2. Remove two nuts off of front body mount. 3. If packer plate is installed from factory re-fit when installing sliders. 4. Using a body clip tool, loosen the wiring harness from the length of the left side frame rail. On the inboard side of the left frame rail, also disconnect the brake lines in the rear. 5. Last Rev Date: 03/03/2022 Page 4 of 8 Fitting instructions# 37801067 Copyright © 2021 by ARB Corporation Limited. All rights reserved, this document must not be reproduced without the express authority of ARB Corporation Ltd 6. Insert M6 cage nut into rear mount of left slider. 7. Using a lift table or a friend, lift the sliders into position and fasten the two body mount nuts onto the studs. Leave loose for now. U BOLT 8. Use the rubber tape to cover the back of the u-bolt and secure the ends with cable ties as shown. 9. Moving to the rear, slide one of the u-bolts under the brake lines and over the frame. Last Rev Date: 03/03/2022 Page 5 of 8 Fitting instructions# 37801067 Copyright © 2021 by ARB Corporation Limited. All rights reserved, this document must not be reproduced without the express authority of ARB Corporation Ltd 10. Using 2x M12 nuts and washers, fasten the slider to the u-bolt Leave loose for now. 11. Using P-Clip provided, attach the wiring harness with an M6x25 bolt and washer to the rear mount so that it can't rub M6 - 9 Nm. 12. With both front and rear loosely attached to the vehicle, move to the middle mount. Bend two nut wands as shown, if lowest middle mount doesn't have a weld nut, use a third nut wand on the lowest position. 13. Insert nut wands into chassis holes shown. Last Rev Date: 03/03/2022 Page 6 of 8 Fitting instructions# 37801067 Copyright © 2021 by ARB Corporation Limited. All rights reserved, this document must not be reproduced without the express authority of ARB Corporation Ltd 1st BOLT FRONT OF VEHICLE REAR OF VEHICLE 3RD BOLT 14. Insert 2x M12x40 bolts, washers, and nyloc nuts into the lower front mount. Use an angled wrench to reach the inner nuts. 15. If some trimming is needed front to rear, the slider can be adjusted with packers in the front or moving the rear vertically. The alignment with the sill can be measured off the bottom of the door with the door slightly open.Clearance should be 10-15mm OA. To adjust the rear, with the u-bolt slightly loose, the slider can be adjust up and down and then while slider is in the correct position, the u-bolt can be tightened to hold the slider at that position. To adjust the front, the slider needs to be removed and 4mm packers can be used underneath the upper area of the front mount. 16. Moving to the right side, if your vehicle is equipped with a gas tank skid, loosen all the bolts holding it on, but don't completely remove. 17. Remove the 1st and 3rd bolts that are located on the frame, holding the gas tank skid on. The front bolt will be re-used for the middle slider mount. 18. Repeat steps 6-8 for the right side. 19. Repeat step 11 for the right side, bending nut wands as shown. Last Rev Date: 03/03/2022 Page 7 of 8 Fitting instructions# 37801067 Copyright © 2021 by ARB Corporation Limited. All rights reserved, this document must not be reproduced without the express authority of ARB Corporation Ltd 20. Find the OE hole on the outside of the rail and insert nut wands If your vehicle was equipped with a gas tank skid, place the skid over the middle mount and u bolt and tighten all bolts with the exception of the 3rd 21. Torque all bolts on the sliders and chassis. M8 - 22 Nm. M10 - 44 Nm. M12 - 77 Nm. FITTED PRODUCT Last Rev Date: 03/03/2022 Page 8 of 8 Fitting instructions# 37801067 Copyright © 2021 by ARB Corporation Limited. All rights reserved, this document must not be reproduced without the express authority of ARB Corporation Ltd