Home - Lincat Catering Equipment
IMC Archives - Lincat Catering Equipment
Instruction Manual for imc fresh thinking models including: FR60, FR90, FR60 Glass Froster, Glass Froster, Froster
Frostar FR60 Glass Froster [Top Load] - Stainless Steel Exterior - W 600 mm - 0.650 kW - Lincat Catering Equipment
File Info : application/pdf, 12 Pages, 778.76KB
DocumentDocumentFROSTAR FR60 AND FR90 Installation, Operating and Servicing Instructions Please make a note of your product details for future use: Date Purchased: _________________________ Model Number: __________________________ Serial Number: __________________________ Dealer: ________________________________ ________________________________ _______ A34/109 R1 Page | 1 ECN 4825 October 2022 CONTENTS WARRANTY....................................................................................................... 3 DELIVERY.......................................................................................................... 3 INTODUCTION .................................................................................................. 3 INSTALLATION.................................................................................................. 5 TURNING LED LIGHTS ON-OFF ....................... Error! Bookmark not defined. REVERSING DIRECTION OF DOOR ................. Error! Bookmark not defined. ELECTRICITY SUPPLY CONNECTION ............................................................ 6 COMMISSIONING ............................................................................................. 6 CHANGING THE CONTROLLER SET POINT................................................... 7 USING YOUR BOTTLE COOLER...................................................................... 7 CLEANING ......................................................................................................... 8 CHANGING SHELF POSITION .......................... Error! Bookmark not defined. MAINTENANCE ................................................................................................. 9 do's and don'ts ................................................................................................... 9 END OF LIFE DISPOSAL ................................................................................ 10 MATERIAL CONTENT ..................................................................................... 10 SPARE PARTS LIST........................................................................................ 11 ORDERING SPARE PARTS ............................................................................ 12 FURTHER INFORMATION .............................................................................. 12 Page | 2 WARRANTY This equipment is guaranteed by Lincat/IMC for 2 years from the date of purchase from Lincat/IMC, or from one of its stockists, dealers or distributors. The guarantee is limited to the replacement of faulty parts or products and excludes any consequential loss or expense incurred by the purchaser. Defects which arise from faulty installation, inadequate maintenance, incorrect use, connection to the wrong electricity supply, or fair wear and tear, are not covered by the guarantee. The guarantee applies in this form to installations within the United Kingdom. Export units carry 2 years "parts only" warranty. Please observe these instructions carefully. DELIVERY The packaged machine consists of: FR60 Glass Froster containing: Small Shelves 2 Large Shelves 1 Instruction Booklet 1 Please notify both the carrier and the supplier within 24 hours of receipt if anything is missing or damaged. Check that the correct machine has been supplied and that the voltage, marked on the rating plate, is suitable for the supply available. The rating plate is located internally on the right hand side of the unit. INTRODUCTION The Frostar FR60 and FR90 are efficient, fast-cooling top loaders with sliding covers suitable for underbar use. The Frostar range is designed to produce a steady supply of chilled glasses. The following quantity of beverage bottles/mixers can be held in each unit: Glass Froster FR60 (900h x 600w x 620d) Capacity (Standard Pint Glasses) 75 Page | 3 Frostar FR60 Dimensions: 625 241 851 902 606 300 LIGHT SWITCH REFRIGERATION CONTROLLER THIS GRILL MUST BE REMOVED IN ORDER 560 TO CLEAN THE AIR FILTER MAINS CABLE Frostar FR60 Dimensions: The internal dimensions of the FR60 are 550mm high, by 526mm wide, by 500mm deep. Page | 4 INSTALLATION For the Installer These Instructions contain important information designed to help the user obtain the maximum benefit from their investment in a Lincat/IMC Mistral Bottle Cooler. Please read them carefully before starting work, and consult with the supplier in the event of any queries. Be sure to leave this Instruction Manual with the user after installation of the machine is complete. Procedure WARNING The following table shows the weight and the minimum quantity of people required to lift each unit: Glass Froster FR60 Net Weight 63.5 kg (max) Quantity of People 4 Install the unit on a flat and level floor. Allowing space for ventilation at the front, back and sides. Do not install the unit close to a heat source such as a radiator or a warm air outlet. Ensure that the unit is standing level by adjusting the feet on the base of the unit. If the cabinet has been stored on its front, back, or sides during transit, stand the cabinet upright for a minimum of two hours before starting. This will avoid damage to the compressor. The unit has an automatic defrost cycle and evaporates all the condensate water without the need for a drainage system. Page | 5 . ELECTRICITY SUPPLY CONNECTION Position the unit in the chosen site. The electricity supply connection should be made to a power outlet socket or isolator mounted on the wall close to the machine. This socket or isolator must be accessible once the machine is installed. Before connecting, check that the voltage shown on the rating label is correct for the electricity supply you have available. If the plug does not fit your sockets or a longer lead is required, changes must be made by an approved electrician. NOTE: The plug is fitted with a 10amp fuse. The plug fuse cover must be refitted when changing the fuse. In the event of losing the fuse cover the plug must NOT be used until a replacement fuse cover has been obtained and fitted or the plug replaced. WARNING: This machine must be earthed Should the supply cord become damaged then a replacement must be fitted by an approved electrician. The IET Codes of Practice must be observed. The wires in the mains lead are coloured in accordance with the following code: Green and yellow Blue Brown Earth Neutral Live COMMISSIONING Before using a bottle cooler for the first time, the interior should be wiped out with a clean damp cloth. Allow the machine to stand for 1 hour to allow the refrigerant to settle. Plug in and switch on at the wall socket. There is no separate switch to turn on the machine. The compressor will start running less than one minute after the supply is switched on. Check that the light is working, and check the switch is operating correctly. Run the unit empty, and check that cold air is being circulated within the cabinet. Page | 6 CHANGING THE CONTROLLER SET POINT The electronic temperature controller is factory set to -12°C and will cycle the air temperature between ±2°. The set point can be adjusted between 5°C and -12°C by following the button sequence below: 1) -11 Press SET the current SET Point will be displayed, if Loc is displayed then the controller is locked, to unlock press and hold the SET button for 3 seconds, UnL will then be displayed. 2) -11 Press SET button and the current set point temperature will be displayed. 3) -10 Use the UP and DOWN buttons, to scroll to the desired set point temperature (min 0°C, max 10°C). 4) -12 Press SET button to accept. Then press stand-by button to esc. Display will revert back to current internal air temperature. USING YOUR GLASS FROSTER Load the cabinet with glasses by placing them on the wire shelves, ensuring that the glasses are standing in an upright position. Do not obstruct the air vents inside the cabinet. All cabinets have an electronic off-cycle defrost controller that de-ices the evaporator for a maximum of 30 minutes every 4 hours using electric heaters. This evaporates the condensate water without the need for a drainage connection. The controller also ensures that the cabinet temperature is maintained at -18°C ±2°C between automatic defrost cycles. Note that this temperature is adjustable (refer to above section "CHANGING THE CONTROLLER SET POINT"). Page | 7 When the unit is not going to be used for several weeks, run it for 24 hours after emptying it, to ensure that all condensate water evaporates. MAKING THE BEST USE OF THE CABINETS Do not overload the cabinet. There should be a gap of at least 40mm above the merchandise on the top shelf, and merchandise should be spaced to allow the circulation of cooled air throughout the cabinet. Do not load the cabinet with boxed goods as this prevents air circulation. Do not place hot or warm goods in the cabinet. Only goods at room temperature or less should be placed in the unit otherwise performance will be affected. Do not run unit with the lid open, as this will cause the evaporator to ice up preventing the unit from working efficiently. Ensure that both the front grille cover attached to the plinth, and the air vents inside the cabinet are always unobstructed. CLEANING Clean lid and surfaces as required, occasionally remove all merchandise and clean interior surfaces with a clean damp cloth. DO NOT USE CLEANING MATERIALS CONTAINING ABRASIVES OR BLEACHES. In the case of heavy soiling use a mild liquid detergent. The unit can be washed on the inside using bicarbonate of soda to remove stale smells. Page | 8 MAINTENANCE Warning Never service, repair or troubleshoot a unit unless you are a professional air conditioning / refrigeration service person. Improper servicing can lead to serious injury or death from fire, electric shock or explosion. Remove the front grille cover. Clean the compressor coil with a brush and vacuum cleaner every three months or when dirty (whichever is sooner). Replace the grille cover. Other than regular cleaning the unit requires no maintenance by the end user. It is recommended that the unit is serviced by a Lincat/IMC approved engineer at least once a year. Details of IMC Service Contracts are available on application. DO'S AND DON'TS Do Install on a level surface. Do Ensure plug is accessible with the unit installed. Do Regularly clean the condenser and compressor. Do Rotate stock of bottles. Don't Sit or stand on the unit worktop. Don't Load with boxed goods. Don't Leave the doors open. Don't Cover the shelves with any protective materials which may obstruct air circulation through them. Don't Install unit in direct sunlight. Don't Block the air inlet grilles. Don't Store food in the unit. Don't Place hot or warm goods in the unit. Don't Use the unit outside. Don't Use mechanical devices to accelerate the defrosting process. Don't Use electrical appliances inside the storage area, unless they are recommended by the manufacturer. Don't Store explosive substances such as aerosol cans with flammable propellant in the appliance. Page | 9 END OF LIFE DISPOSAL At the end of its useful life the unit must be disposed of correctly and safely, to meet the requirements of EU legislation regarding the recovery of ozone depleting substances. The unit must be sent to a specialist recovery, recycling and disposal site that is licensed for the disposal of refrigerated equipment. Please note that the insulation in the Mistral range does not contain any ozone depleting substances. The refrigerant used in the Mistral M60, M90 and M135 is R290a. Warning The refrigerant used in this Bottle Cooler is R290a and is Flammable MATERIAL CONTENT The Mistral units may contain a combination of the following materials; Metals Stainless Steel, Mild Steel (Inc. Nickel Plated, Chrome Plated & Zinc Plated), Aluminium and Copper. Plastics & Rubber PVC, Nylon, Polypropylene, Polycarbonate, Polyester, Acetate, Neoprene Rubber and Silicone Rubber. Insulation Polystyrene, Polyurethane Foam. Oils & Gases Ester oil, Refrigerant R290a. Other Glass, Magnesium Oxide, electronic components. Page | 10 SPARE PARTS LIST Frostar FR60 Part No A12/047 A12/048 849407 E49/407/B A21/011 G30/545 G60/348 Description Wire Shelf (large) Wire Shelf (small) Plinth Grille Cover (Stainless Steel) Plinth Grille Cover (Black Painted) Lock, clip & keys Electronic Controller Mains Cable S49/175 J09/049 J09/026 DR16 S/R0100 (2.0mtr) G42/071 G96/049 SO21 Refrigeration Pack Condenser Evaporator Service Drier Capillary TC60 Compressor Evaporator Fan Solenoid Valve G50/120 G30/544 G45/175 A11/264 LED strip Transformer Light switch Door Gasket Page | 11 ORDERING SPARE PARTS In the event that spare parts or accessories need to be ordered, please always quote the SERIES AND SERIAL NUMBER of the machine. This is to be found on the rating plate located near the supply cable. For installations outside the UK please contact your supplier. For information on IMC spares and service support (if applicable), please call Lincat on +44 (0) 1522 875520. Alternatively, contact us via email: Lincat Spares Desk E-mail: spares@Lincat.co.uk Lincat Service Desk E-mail: service@Lincat.co.uk Lincat Limited Whisby Road, Lincoln, LN6 3QZ, United Kingdom Tel: +44 (0)1522 875500 E-mail: info@Lincat.co.uk Website: www.Lincat.co.uk FURTHER INFORMATION HTTPS://LINCAT.CO.UK/BRANDS/IMC https://www.youtube.com/watch?v=1hSfEPKi-fg Page | 12