Duratech PL-REM-200 LINK Driver Manual

Manual

PL-REM-200

This manual is available in multiple languages:

• English: Page 2
• Nederlands: Pagina 8
• Français: Page 14
• Deutsch: Seite 20

The PL-REM-200 LINK Driver is designed for controlling pool lighting systems.

Table of Contents

• Technical specifications
• Box contents
• Installation instructions
• Pairing Handheld Transmitter & controller
• Handheld transmitter functions
• Replacing transmitter battery
• Troubleshooting

Technical Specifications

Electrical specifications

• Nominal Input voltage: 230 VAC 50 Hz
• Output voltage on Lamp Output: 12 VAC
• Max output current on Lamp Output: 16.7 A
• Max rating Relay Contact A and B: 14A 250VAC, 14A 30VDC
• Resistive Load: 6A 250VAC, 6A 30VDC
• Inductive Load: 200VA
• Transformer VA rating: 5x20mm cartridge fuse, 5A 250V slow blow/time lag
• Frequency band transmitter: 868 MHz
• IEC Protection Class: Class II

General specifications Controller

• Ambient air temperature: 0°C ... +40°C
• Humidity: 10% ... 90% RH, non condensing
• Dimensions: 195x194x90 mm
• Weight: 3.2 kg
• Ingress protection rate: IP54

Box Contents

The box contains:

1. PL-REM-200 controller
2. Handheld transmitter (DuraLink™ version)
3. Spare battery (type A23 12V)
4. Screws (4x) & wall plugs (4x)
5. Owner's manual

A diagram shows the controller unit, the handheld transmitter, a battery, screws and wall plugs, and an open manual.

Installation Instructions

• Connect a 230VAC power source to the “220-240VAC INPUT” terminal.
• Connect the swimming pool lights to the “Lamp 12VAC output” terminal.
• Ensure the total load of pool lights does not exceed 200 Watt.

Optional: The “Switch A” & “Switch B” terminals can be used to control auxiliary circuits like a pool cover or garden lights.

A wiring diagram illustrates the connections for power input, pool lights, pool cover, and garden lights, showing the PL-REM-200 controller with its terminals and connections.

Pairing Handheld Transmitter & Controller

The handheld transmitter is pre-paired at the factory. The PL-REM-200 can be paired with up to 6 handheld transmitters. Manual pairing can be performed if necessary.

Manual Pairing Process:

1. Ensure the PL-REM-200 is connected to a power source.
2. Press the pairing button on the small circuit board inside the controller for at least 5 seconds. The LED will start to blink fast.
3. Within 25 seconds, press any button on the handheld transmitter.

Successful pairing is indicated by the LED flashing slowly 5 times. If the pairing memory is full (6 devices paired), the LED will flash 15 times.

Unpairing All Transmitters:

Push the pairing button for at least 5 seconds, then do nothing for at least 25 seconds. The pair memory will be erased, and the green LED will flash 5 times.

Important: If no transmitters are paired, the PL-REM-200 will accept messages from any transmitter.

A diagram shows the controller with a "Pairing button" and "Green LED" highlighted, and the handheld transmitter.

Handheld Transmitter Functions

• ON/OFF Button: Toggles the lamps ON/OFF.
• Color Button: Goes to the next color scenario.
• Button A: Toggles Output A ON/OFF.
• Button B: Toggles Output B ON/OFF.

Replacing Transmitter Battery

• Remove the Phillips head screw and open the transmitter.
• Replace the battery, respecting the polarity.
• Battery type: A23 12V.

Diagrams illustrate the process of opening the transmitter and replacing the battery.

Troubleshooting

Problem: The controller does not react to transmitter commands

• Check the battery of the handheld transmitter.
• The transmitter is not paired correctly with the controller. Repeat the pairing process.
• Reduce the distance between the handheld transmitter and the PL-REM-200 and/or remove obstacles.

Problem: The pool lights do not work

• Check the red status LED.
• Check if there is 12VAC output at the controller's terminals.
• Check the fuse of the controller. If the fuse is okay and there is still no 12VAC output, contact your distributor.

Declaration of Conformity

Declarations of conformity covering this product are available for download from the House of Duratech website: www.duratech.be