User Manual for URUAV models including: Flipo F95
Flipo F95 5.1 5.8GIPEXleft-handedantenna Frequencyrange（MHz）：5600～5950MHz Polarization：Right-handedRHCP InputImpedance：50Ω VSWR（5800MHZ）≤1.5
1. Flipo F95. PNP QUICK START GUIDE ... Support TBS Smart Audio ... If the user chooses one of the eight channels that OSD parameters.
File Info : application/pdf, 12 Pages, 1.71MB
DocumentDocumentFlipo F95 PNP QUICK START GUIDE 1 Flipo F95 Catalog PackageInclude.........................................................................................- 1 1.1 Framekit............................................................................................. . - 2 2.1 1106-4500kvmotor(black)...................................................................- 3 3.1 F405 15A AIO FC ..........................................................................- 4 4.1RunCam Nano 2 FPV Camera .............................................................- 5 5.1 XF5805/5.8G 40CH VTX........................................................................- 55.1 5.8G Rush IPEX Left-handed antenna................................................ -6 6.1 GEMFAN D63 3-blade Propeller ....................................................... - 67.1 Recommended owersupply.................................................................- 6 10.1Adjusting parameter......................................................................- 7 (1)Configuration of UART port parameters............................................-7 (2)Frequency grouping and channel number configuration...................- 7 Enter OSD parameter menu.............................................................- 8Start grouping and channel configuration.......................................- 9 Output power configuration........................................................- 10 Channel number indication...........................................................- 11 - 1 Package Include 1*Flipo F95 PNP 1*GEMFAN D63 gray 3-blade Propeller4 positive 4 negative 2*battery strap 2*Black battery non-slip mat 1* M2*7 Countersunk Screws(6pcs) 1* M2*7 Cup head screw(8pcs) Flipo F95 1.1 Frame kit Wheelbase100mm Blade size:2.5inches Image transmission hole distanceM2x20x20mm Motor pitchM2x9x9mm 2 2.1 1106-4500KV motor (black) Motor KV:4500rpm/v Lipo Cell2-4S Weight10.8g Idle CurrentIO/10V0.185 Max Continuous Current7.0A Max Continuous Power 110W Max thrus269G16.8V/4024R Configu - ration12N/14P Motor ResistanceRm0.481 Stator Diameter13mm Stator Length6mm Motor Dimensions14.2mm*14.5mm Overall Shaft Length4mm Shaft Diameter1.5mm Bolt holes spacing:9*9mm Bolt threadM2 Propeller 2.5" Flipo F95 3 Flipo F95 3.1 F405 15A AIO FC FC parameters CPU STM32F405168MHz IMUMPU6000SPI connection size30mm*30mm Mounting Hole:26x26mm FirmwareGEPR/GEPRCF405 OSDBuilt-in OSDSTM32 controls the OSD chip via SPI ReceiverStand by FrskyXM/XM+Receiver/Futaba Receiver/Flysky Receiver/TBSCrossfire Receiver programmable LED such as WS2812 :Support Built-in current sensor Reserved buzzer interface Reserved DJI port Weight6.4g ESC parameters BLHELI_S all functions:Support PWMOneshot125Oneshot42MultishotDshot150Dshot300 Dshot600: Support Input voltage2S-4SLipo Constant current12A Peak current18A CPUEFM8BB21F16G Motor connector1.25mm pin header connector FirmwareG-H-30-16.7 4 Flipo F95 4.1 RunCam Nano 2 FPV Camera Item: RunCam Nano 2FPV Camera Beeldsensor: 1/3 "CMOS Horizontale Resolutie: 1200TVL Lens: 2.1mm(M8) FOV 155 ° Signaal Systeem: NTSC / PAL S/N Ratio: >50dB Elektronische Sluitertijd: Auto Auto Gain Control (AGC): Auto Min. Verlichting: 0.01Lux1.2F D-WDR: Auto Dag/Nacht: Kleur Power: DC 3-5.5V Stroom: 110mA @ 5V 120mA3.3V Behuizing Materiaal: ABS Netto Gewicht: 3.4g Afmetingen: L14mm * W14mm * H16mm 6.2 XF5805/5.8G 40CH VTX Support TBS Smart Audio Transmitting power: 0/25/100/300/400mw Frequency points: 40ch Video format: complete NTSC / PAL format Input voltage: 7V26V Power consumption: +12V600MW, 260ma @ Size: 25×20×4mm Weight: 3.2g (except for antenna) Equipped with copper tube mini antenna (ipex interface) Ps: The antenna must be installed before power on to avoid the possibility of burning the tuner. Flipo F95 5.1 5.8G IPEX left-handed antenna Frequency rangeMHz56005950MHz PolarizationRight-handed RHCP Input Impedance50 VSWR5800MHZ1.5 Maximum input power50W Input connector type:UFL Size15*78MM±2 Antenna weight2.5g Radome materialABS Radome colorblack Operating temperature-4060°c Rated Wind Velocity 60m/s 6.1 GEMFAN 63mm 2.5 inch propeller Specification:D63 Diameter2.5inch Paddle diameter63.5MM Materialimported Bayer PC Mounting holes1.5MM/4 holes Center thickness:4.9MM Quantity:2pairs Colorblack Weight1.4g/PCS 7.1 Recommended power supply Recommended voltage:2S-4S Recommended capacity:350-900 Mah Flipo F95 8.1 Adjusting parameter (1) Configuration of UART port parameters Enter the Ports item, select the UART port (UART3 in this case), and then select the TBS Smart Audio item (Figure 1) in the Peripheral column to complete the configuration of the flight control image serial port. If the connection between the image transmission and the selected flight control UART port remains unchanged, this step only needs to be operated once. (2) Frequency grouping and channel number configuration Enter OSD parameter menu When VTX1 image transmission, corresponding image transmission receiver display screen and flight control are powered on, the information shown in Figure 2 will appear on the receiving screen. Figure 2 Electrical display information At this time, according to the screen prompt operation THR MID Flipo F95 (throttle center), YAW LEFT (YAW rocker to the left), PITCH UP (PITCH rocker to the top) into the OSD parameter adjustment menu (Figure 3). Figure 3 OSD parameter menu Start grouping and channel configuration Under the OSD MAIN menu, the PITCH rocker can move the cursor arrow up and down to select the menu item, select the FEATURES item, then select the ROLL rocker to the right, and enter the lower configuration menu (Fig. 4). Figure 5 FEATURES Menu In the menu of Figure 4, select the desired frequency grouping BAND and channel CHAN by swinging the ROLL rocker left and right. Flipo F95 Note: Because VTX1 supports 48 channels, users can select any of the 48 channels by pressing keys. But at present, Betaflight's OSD parametric function only supports 40 channels, so users can only configure 40 channels on the OSD screen. If the user chooses one of the eight channels that OSD parameters do not support and enters OSD parameters, the system will automatically change the user's original channel to A1 channel on our frequency table (5865 MHz), that is, the user can configure only 40 channels with OSD parameters. After configuring the grouping and channel, you need to enter the SET item and select YSE to take effect (Figure 6). Figure 6 Grouping and channel configuration validation Output power configuration As in the previous section, the POWER item can be entered by remote control selection, and the required transmission power can be selected (Fig. 7). VTX1 currently supports only 25 mW power options, while the POWER menu with OSD parameters has four options: 25 mW, 200 mW, 500 mW and 800 mW. Therefore, users need to pay attention to the choice of 200 mW, 500 mW, 800 mW options will be VTX1 set to 25 mW transmission power. Note: Unlike configuring BAND and CHAN, POWER settings do not need to enter the SET entry confirmation, and take effect immediately. Flipo F95 Figure 7 Transmission Power Selection Channel number indication The LED lamp displays the set grouping and channel, and the corresponding working frequency is shown in the table below. Channel select : Select channels by simple short presses. Blue LED light on stands for CH1,short presses to change 8 channels sequentially. Band select: Press button for 2S,Green LED will flash,then short presses to select 5 bands. Power select: Press button for 4S,Red LED will flash,then select power by simple short presses to select 25mW/200mW/600mW/800mW. Blue light indicates FR, green light indicates CH, hollow circle indicates off, solid circle indicates ON Flipo F95 Precautions for use: Before power on, make sure that the output terminal has an antenna installed to avoid damaging the internal components; Note that the input voltage is within the specified range and positive and negative, so as to avoid damaging the internal components; If you want to change the antenna, please choose the antenna with good standing wave and gain to get a long transmission distance; Pay attention to electrostatic protection during transportation, installation and use;WPS 文字