Hormann Garage Side Sectional Doors Series 35

Table of Contents

• Door Type, Door Leaf, Abbreviations Used

• HST 42, M-Sicke (Operator-operated)

• HST 42, L-Sicke (Operator-operated and manually operated)

• Design Elements for M- and L-Sicke

• Glazing for M- and L-Sicke

• HST 42 with Pass Door, L-Sicke

• HART 42, Aluminum Frames from Standard Profiles (Operator-operated)

• ES Fitting - Operator Wall Mounting

• DS Fitting - Operator Wall Mounting Small Side Clearance AKS

• ES Fitting - Operator Ceiling Mounting A

• ES Fitting - Operator Ceiling Mounting B

• ES Fitting - Operator Ceiling Mounting C

• ES Fitting - Operator Ceiling Mounting B, C / Wall Mounting Sliding Door

• Details

• Details Aluminum Frame

• Solution for Narrow Reveals or in the Reveal

• Fixed Elements HST 42

• Side Doors NT 60 HST 42 with Corner Frame made of Aluminum Profiles

• Side Doors NT 60 HST 42 with Block Frame made of Aluminum Profiles

• 2-Leaf Side Doors NT 60 HST 42 with Block Frame made of Aluminum Profiles

General Information

Please always consider country-specific building regulations. Fitting and door leaf equipment with installation examples can be found in this manual.

Before installing the side sectional doors, the door opening and the garage floor must be completed.

Reprinting (including excerpts) only with our permission. Copyright protected. All dimensions in mm. Construction changes reserved.

Door Types and Leaves

Seiten-Sektionaltor HST – Steel Double-Walled Slats

M-Sicke Deco-, Plain-, Silk-, Slate- or Woodgrain

• Double-walled, PU-foamed door sections, outer side with Deco-, Plain-, Silk-, Slate- or Woodgrain, inner side with stucco embossing.
• Uniformly wide door sections, vertically ribbed, made of galvanized sheet steel.
• Surface with high-quality coating on both sides (for Decograin with high-quality plastic film coating on the outside).
• Glazing possible.
• Design elements possible.
• Ventilation grilles possible in the lower door area.

L-Sicke Deco-, Plain-, Silk-, Slate-, Wood- or Duragrain, Planar

• Double-walled, PU-foamed door sections, outer side with Deco-, Plain-, Silk-, Slate-, Wood- or Duragrain, inner side with stucco embossing.
• Uniformly wide door sections, vertically ribbed, made of galvanized sheet steel.
• Surface with high-quality coating on both sides (for Decograin with high-quality plastic film coating on the outside).
• Glazing possible.
• Design elements possible.
• Ventilation grilles possible in the lower door area.

Further details can be found in the brochure.

Used Abbreviations

Seiten-Sektionaltor HST 42 - M-Sicke

Operator-operated

Views

The proportions in the illustrations correspond to a size of 2500 x 2125 mm. Deviations may occur for other door sizes.

Size Range for ProMatic Operator

Size Range Requires SupraMatic Operator

Basic Model

Notes:

• Heights in 5 mm increments, widths in 1 mm increments possible.
• Glazing / motifs are not possible in the 1st and last section.
• Manually operated up to LZ 5000 mm.

Seiten-Sektionaltor HST 42 - L-Sicke

Operator-operated and manually operated

Views

The proportions in the illustrations correspond to a size of 2500 x 2125 mm. Deviations may occur for other door sizes.

Size Range for ProMatic Operator

Size Range Requires SupraMatic Operator

Size Range Only for 180° Sliding Door, Manually Operated, Not Possible with Aluminum Frame

Basic Model

Notes:

• Heights in 5 mm increments, widths in 1 mm increments possible.
• Glazing / motifs are not possible in the 1st and last section.
• Manually operated up to LZ 5000 mm.

Seiten-Sektionaltor HST 42 - Design Elements for L-Sicke

The arrangement of motifs (views correspond to door size 2500 x 2125 mm) is not possible in the 1st and last section; other arrangements are available upon request. Number of motifs according to technical feasibility.

Motif 451 / 461

Motif 451: With stainless steel frame, external dimension 240 x 240 mm (not possible with M-Sicke).

Motif 461: With stainless steel frame and plastic double glazing or 3-pane insulating glass, clear/clear, glazing with plastic double glazing, 41 mm, clear/clear or crystal structure/crystal structure, clear view 160 x 160 mm. External dimension 240 x 240 mm.

Motif 471 / 481

Motif 471: With stainless steel frame, external dimension 240 x 240 mm (not possible with M-Sicke).

Motif 481: With stainless steel frame and plastic double glazing or 3-pane insulating glass, clear/clear, glazing with plastic double glazing, 41 mm, clear/clear or crystal structure/crystal structure, clear view 160 x 160 mm. External dimension 240 x 240 mm.

Motif 459 / 469

Motif 459: With stainless steel ring, external dimension Ø 280 mm (not possible with M-Sicke).

Motif 469: With stainless steel ring and plastic double glazing, glazing with plastic double glazing, 41 mm, clear/clear or crystal structure/crystal structure, clear view Ø 200 mm. External dimension Ø 280 mm.

Notes:

• Heights in 5 mm increments are possible.
• Number of motifs according to technical feasibility:
• Less than 2375 mm: 3 design elements.
• Greater than 2375 mm: 4 design elements.

Seiten-Sektionaltor HST 42 - Glazing for M- and L-Sicke

Arrangements (views correspond to door size 2500 x 2125 mm) of glazing are not possible in the 1st and last section; further arrangements upon request. Number of glazings according to technical feasibility.

Clear view of glazing 202 x 375 mm, frame external dimension 270 x 395 mm.

S0

M-/L-Sicke: With plastic double glazing, 22 mm, clear/clear or crystal structure/crystal structure.

S1

M-/L-Sicke: With plastic double glazing, 22 mm, clear/clear or crystal structure/crystal structure.

S2

M-/L-Sicke: With plastic double glazing, 22 mm, clear/clear or crystal structure/crystal structure.

Seiten-Sektionaltor HST 42 with Pass Door - L-Sicke

Views

The proportions in the illustrations correspond to a door height of 2125 mm. Deviations may occur for other door heights. The floor in front of and inside the garage must be level or slope outwards.

Door View

LDBS: 480 mm

TH: 562 mm

Pass Door

• The pass door is a foldable section (TH 562) and only possible with the L-Sicke version.
• The clear passage width of the pass door is 480 mm and the threshold height is 20 mm.
• Only possible in the 1st section on the closing side (ASS).
• Only opens inwards.
• Possible with DS and ES fittings.
• No operator ceiling mounting possible.
• Only operator wall mounting possible (see pages 10 and 11).

Notes:

• Not possible with integrated overhead door closer.
• Not possible with multiple locking.
• Design elements and glazing are not possible in the pass door section.

Seiten-Sektionaltor HART42 - Aluminum Frames from Standard Profiles 42 mm

Operator-operated

Views

The proportions in the illustrations correspond to a size of 2500 x 2125 mm. Deviations may occur for other door sizes.

Size Range for ProMatic Operator

Requires SupraMatic Operator

Standard Sizes

Basic Model

Notes:

• Uniform glazing and uniform sections.
• Handle HST-FS with pass door function (partial opening) is not possible.
• Heights in 5 mm increments, widths are not possible.
• Not possible with pass door.

Seiten-Sektionaltor HST 42 - ES-Beschlag

Operator Wall Mounting (AKS < 540)

Manual Operation (LZ < 5000)

Views

The proportions in the illustrations correspond to a size of 2250 x 2125 mm. Deviations may occur for other door sizes.

Notes:

• The clearance for mounting and subsequent operation of the door must be clear.
• Delivery of the floor threshold as 1 package.
• If necessary, shorten the operator rail on site (W ≥ LZ + 1100).
• Operator wall mounting only possible up to AKS < 540.

Bottom Threshold Section

Track Section

Notes:

• 1) AKS > 700 to 1000 possible for doors without operator, AKS > 1000 with "Reveal Depth Extension HST" set possible.
• 2) If LZ > 6000, the operator rail must be offset by dimension "Y".
• With aluminum frame, only 90° possible.

Seiten-Sektionaltor HST 42 - DS-Beschlag

Operator Wall Mounting Small Side Clearance AKS

Manual Operation (LZ < 5000)

Views

The proportions in the illustrations correspond to a size of 2250 x 2125 mm. Deviations may occur for other door sizes.

Notes:

• The clearance for mounting and subsequent operation of the door must be clear.
• Delivery of the floor threshold as 1 package.
• If necessary, shorten the operator rail on site (W ≥ LZ + 1100).

Bottom Threshold Section

Track Section

Notes:

• 1) LZ > 5000 2-part version.
• 2) Aluminum frame possible from AKS 220 mm.

Seiten-Sektionaltor HST 42 - ES-Beschlag

Operator Ceiling Mounting A

Views

The proportions in the illustrations correspond to a size of 2250 x 2125 mm. Deviations may occur for other door sizes.

Notes:

• The clearance for mounting and subsequent operation of the door must be clear.
• Delivery of the floor threshold as 1 package.
• If necessary, shorten the operator rail on site (W ≥ LZ + 1100).

Bottom Threshold Section

Track Section

Notes:

• For aluminum frames and pass doors, only 90° is possible.
• 1) LZ > 5000 2-part version.

Seiten-Sektionaltor HST 42 - ES-Beschlag

Operator Ceiling Mounting B

Views

The proportions in the illustrations correspond to a size of 2250 x 2125 mm. Deviations may occur for other door sizes.

Notes:

• The clearance for mounting and subsequent operation of the door must be clear.
• Delivery of the floor threshold as 1 package.
• If necessary, shorten the operator rail on site (W ≥ LZ + 1100).

Bottom Threshold Section

Track Section

Notes:

• For aluminum frames and pass doors, only 90° is possible.
• 1) AKS values > 1000 possible with "Reveal Depth Extension HST" set.

Seiten-Sektionaltor HST 42 - ES-Beschlag

Operator Ceiling Mounting C (AKS < 540 / ASS < 115)

Views

The proportions in the illustrations correspond to a size of 2250 x 2125 mm. Deviations may occur for other door sizes.

Notes:

• The clearance for mounting and subsequent operation of the door must be clear.
• Delivery of the floor threshold as 1 package.
• If necessary, shorten the operator rail on site (W ≥ LZ + 1100).

Bottom Threshold Section

Track Section

Notes:

• For aluminum frames and pass doors, only 90° is possible.
• 1) AKS values > 1000 possible with "Reveal Depth Extension HST" set.

Seiten-Sektionaltor HST 42 - ES-Beschlag

Operator Ceiling Mounting B, C and Wall Mounting Sliding Door

Views

The proportions in the illustrations correspond to a size of 2250 x 2125 mm. Deviations may occur for other door sizes.

Notes:

• The clearance for mounting and subsequent operation of the door must be clear.
• Delivery of the floor threshold as 1 package.
• If necessary, shorten the operator rail on site (W ≥ LZ + 1100).

Ceiling Mounting B / C Bottom Threshold Section

Ceiling Mounting B Track Section

Ceiling Mounting C Track Section

Wall Mounting Bottom Threshold Section

Wall Mounting Track Section

Seiten-Sektionaltor HST 42 - Details

Door in Intermediate Width

Side Wall DS Fitting Upper Clearance

Side Wall ES Fitting Upper Clearance

Front Wall Upper Clearance

Bottom Threshold

Bottom Thresholds with Drainage (EW)

Seiten-Sektionaltor HST 42 - Details Aluminum Frame

Door in Intermediate Width

Side Wall DS Fitting Upper Clearance

Side Wall ES Fitting Upper Clearance

Front Wall Upper Clearance

Set Mounting Bracket Aluminum Frame

Seiten-Sektionaltor HST 42 - Solution for Narrow Reveals or in the Reveal

The proportions in the illustrations correspond to a size of 2500 x 2125 mm. Deviations may occur for other door sizes.

Notes:

• Technical inspection required.
• Deviating construction / performance characteristics.

Narrow Reveal, ES Fitting, Operator Ceiling Mounting B and 2 Fixed Elements with Sicke Alignment

Installation in the Reveal, DS Fitting, Operator Wall Mounting, Pipe 160 x 60 and 120 x 60

Fixed Elements HST 42

Views

M-Sicke

L-Sicke

Possible Installation Types

In the Opening

AUSS: Outside

AW: Aluminum Angle

LF: Clear Finished Dimension

RAMB: Frame Outer Width

RAMH: Frame Outer Height

INNEN: Inside

Installation Examples

RAMB ≥ 135 mm.

Nebentüren NT 60 HST 42 with Corner Frame made of Aluminum Profiles

Views

M-Sicke

L-Sicke

Dimensions

Inside Opening Installation (Opening Inwards)

AUSS: Outside

OFF: Top Edge Finished Floor

DRH: Handle Height

RAMH = BRH + 28 (LMH + 18)

LDH = BRH - 38

BRH = LMH - 10

LMB: Clear Masonry Width

LMH: Clear Masonry Height

BRB = LMB - 10

LDB = BRB - 76

RAMB = BRB + 56 (LMB + 46)

Clear Passage Width for Leaf Opening of 90°

With externally mounted hinges, maximum opening angle 180°

LDB 90° = BRB - 114

Outside Opening Installation (Opening Inwards or Outwards)

AUSS: Outside

OFF: Top Edge Finished Floor

RAMH = BRH + 28 (LMH + 18)

LDH = BRH - 38

BRH = LMH - 10

LMB: Clear Masonry Width

LMH: Clear Masonry Height

LDB = BRB - 76

BRB = LMB - 10

RAMB = BRB + 56 (LMB + 46)

Clear Passage Width for Leaf Opening of 90°

With externally mounted hinges, maximum opening angle 180°

LDB 90° = BRB - 114

With concealed hinges, maximum opening angle 162°

Abbreviations:

AUSS: Outside

BRB: Standard Width

BRH: Standard Height

DRH: Handle Height

FLAM: Leaf Outer Dimension

LDB: Clear Passage Width

LDH: Clear Passage Height

LMB: Clear Masonry Width

LMH: Clear Masonry Height

RAM: Standard Dimension

RAMB: Frame Outer Width

RAMH: Frame Outer Height

OFF: Top Edge Finished Floor

Nebentüren NT 60 HST 42 with Block Frame made of Aluminum Profiles

Views

M-Sicke

L-Sicke

Dimensions

Inside Opening Installation

RAMH = BMH

OFF: Top Edge Finished Floor

AUSS: Outside

DRH: Handle Height

Inside Opening Installation (Opening Inwards or Outwards)

AUSS: Outside

LDH = RAMH - 70

LMH = RAMH + 10

LMB = LDB

LDB = RAMB - 140

RAMB = BMB = LMB + 140

Clear Passage Width for Leaf Opening of 90°

With externally mounted hinges, maximum opening angle 180°

LDB 90° = RAMB - 162

With concealed hinges, maximum opening angle 162°

LDB 90° = RAMB - 148

Abbreviations:

AUSS: Outside

BMB: Standard Width

BMH: Standard Height

DRH: Handle Height

FLAM: Leaf Outer Dimension

LDB: Clear Passage Width

LDH: Clear Passage Height

LMB: Clear Masonry Width

LMH: Clear Masonry Height

RAM: Standard Dimension

RAMB: Frame Outer Width

RAMH: Frame Outer Height

OFF: Top Edge Finished Floor

Nebentüren NT 60 HST 42 - 2-Leaf Side Doors with Block Frame made of Aluminum Profiles

Views

M-Sicke

L-Sicke

Dimensions

Installation in the Opening

Installation in the opening, opens inwards or outwards, DIN right or DIN left.

RAMB = LMB - 20

LDB = RAMB - 140

RAMH = BMH

Notes:

• The floor must be level or have a slope to ensure proper opening of the 2-leaf side door.
• Technical inspection required!

Installation Arrangements

Installation in the opening, opens outwards or inwards, DIN right.

RAMB

LDB GF

LDB GF + SF

RAMH = BMH

AUSS

OFF

Installation in the opening, opens outwards or inwards, DIN left.

RAMB

LDB GF

LDB GF + SF

Clear Passage Width for Leaf Opening of 90°

With externally mounted hinges, maximum opening angle 180°

LDB 90° = RAMB - 222

With concealed hinges, maximum opening angle 162°

LDB 90° = RAMB - 296

Abbreviations:

BMB: Standard Width

BMH: Standard Height

DRH: Handle Height

FLAM: Leaf Outer Dimension

LDB: Clear Passage Width

LDH: Clear Passage Height

LMB: Clear Masonry Width

LMH: Clear Masonry Height

RAM: Standard Dimension

RAMB: Frame Outer Width

RAMH: Frame Outer Height

OFF: Top Edge Finished Floor

GF: Gang Leaf

SF: Stand Leaf

Notes

This section is intended for notes.

Brand Quality for Residential and Commercial Construction

The family company Hormann offers all important building elements for construction and modernization from a single source. They are manufactured in highly specialized plants according to the latest state of technology. Furthermore, our employees work intensively on new products, continuous further developments, and detailed improvements. This is how patents and market-leading positions are created.

Website: https://www.hoermann.com/