DECT Extra Handset Guide

Portable Audio Handset Features

Note: Always range test the unit on site before installation.

Calling Another Handset

To call another handset, press the [call button]. The unit will display 'HS1', 'HS2', 'HS3', or 'HS4', depending on the number of handsets coded into the system. Use the [up arrow]/[down arrow] buttons to select the desired handset, then press the [OK button] to initiate the call.

Changing Ring Volume

Press the [volume up]/[volume down] buttons to increase or decrease the ring volume. Press the [OK button] to save the new setting.

Adjusting Relay Time

Press the [Relay 2 button] for 3 seconds. Scroll through the menu until 'ti' (relay time) is displayed. Press the [OK button] to select 'ti' and adjust the relay times. Press the [OK button] again to confirm your selection. Press the [left arrow] button to exit the process. Both relays will share the same relay time.

Voicemail

If a call is not answered within 40 seconds, the visitor can leave a message. Once a message is left, the handset will display the [Voicemail Symbol]. The unit can store up to 16 voice messages.

To listen to a voicemail, press the [OK button]. If multiple messages are stored, use the [up arrow]/[down arrow] buttons to select the required message and press [OK button] to play. Press the [left arrow] button once to delete the current message, or press and hold the [left arrow] button to delete all messages.

Changing Ring Tone

Press the [call button]. The handset will ring with its currently selected tone. Use the [up arrow]/[down arrow] buttons to cycle through the available ring tones. Press the [OK button] to select and save your chosen tone.

Handset Batteries

Handsets are included with 2 x AAA 600mA rechargeable batteries.

Re-coding/Adding Extra Handsets

Occasionally, the system may need to be re-coded after installation. If a handset does not ring when a call button is pressed, re-coding may be necessary.

Key: ( [CODE BUTTON] = FULL RE-CODE : STEP 1-5) | ( [CODE BUTTON] = ADDING A HANDSET : STEP 3-5)

The process involves a 'TRANSMITTER CODE BUTTON' located inside the transmitter module. Diagrams show the '603/703 DECT' and '705 DECT' transmitter models. The CODE BUTTON is also shown on the back of the wall-mounted unit.

Re-coding Steps:

1. Press and hold the [CODE BUTTON] inside the Transmitter Module for 5 seconds until an audible tone is heard from the intercom speaker. (On the 603 Transmitter, the blue LED marked D17 should also flash.)
2. Then, press the [CODE BUTTON] 14 times and wait for the melody to be heard or the LED to turn off. Note: Performing this step will remove ALL previously synced handsets and clear ALL voicemails.
3. Press and hold the [CODE BUTTON] inside the Transmitter Module for 5 seconds until an audible tone is heard from the intercom speaker. (On the 603 Transmitter, the blue LED marked D17 should also flash.)
4. Then, press and hold the [CODE BUTTON] on the handset until the red LED at the top begins to flash. After a few seconds, a melody will play to confirm successful connection. (Repeat Steps 3 and 4 for each new handset.)
5. Finally, test the kit to ensure all functions work as expected. Press the [call button] on the CallPoint to verify the handset and/or wall-mounted unit receives the call and that two-way speech is functioning correctly.

Portable Video Handset Features

Note: Video handsets must be added first, and only one video handset is supported per system MAX.

Answering a Call

1. When the intercom is called, identify the visitor on the screen.
2. Press the [OK button] to answer the incoming call.
3. Speak clearly into the microphone at a distance of 10-20cm.
4. During the call, press the [left arrow]/[right arrow] buttons to increase or decrease the volume.
5. Press the [GATE/DOOR TRIGGER button] to release the door/gate. Press the [OK button] to end the call.

Note: The video feed will remain active for 1 minute after the audio call has ended.

The portable video handset features a screen for visitor identification, a microphone, indicators for reception and battery level, an ON/OFF button, an OK button, directional buttons, and a GATE/DOOR TRIGGER button. It connects via DC IN.

Changing Settings on Handset

The following settings can be changed on the handset at any time:

1. Adjust brightness.
2. Select language (English, French, or German).
3. Listen to or delete voicemail messages.
4. Change the ring tone.
5. Change screen colour.

Navigation: Use the [up arrow]/[down arrow] buttons to navigate menus, and press the [OK button] to select an option. Press the [right arrow] button at any time to exit or cancel changes.

Accessing Menu: Access the settings menu by holding the [monitoring button] for 3 seconds.

Support Information

Still having trouble? Find all support options, such as Web Chat, Full Manuals, and Customer Helpline, on the AES website:

https://www.aesglobalonline.com