TOTAL | TOTAL Tools Official Site | One-Stop Tools Station
Instruction Manual for TOTAL models including: TH1153216 Series 1500W Industrial Rotary Hammer, TH1153216 Series, 1500W Industrial Rotary Hammer, Industrial Rotary Hammer, Rotary Hammer, Hammer
12 февр. 2025 г. — Read the instruction manual before using. CE conformity. Wear safety glasses, hearing protection and dust mask. Waste electrical products should not be disposed ...
WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or.
File Info : application/pdf, 12 Pages, 36.69MB
DocumentDocumentROTARY HAMMER TH1153216,TH1153216-4,TH1153216-6, TH1153216-8,TH1153216-9,TH1153216S SCAN FOR VIDEO TOTAL TOOLS WORLD 1500W The symbols in instruction manual and the label on the tool Double insulated for additional protection. Read the instruction manual before using. CE conformity. Wear safety glasses, hearing protection and dust mask. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. Safety alert. Please only use the accessories supported by the manufacturer. Original Instructions GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 1) Work area safety a) Keep work area clean and well lit. Cluttered and dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2) Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tools in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. 3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the offposition before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) Service a) Have your power tool serviced by a qualified repair person using only identical. This will ensure that the safety of the power tool is maintained. Additional Safety Warnings Hammer safety warnings Wear ear protectors. Exposure to noise can cause hearing loss. Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury. Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock. Residual risks Even when the power tool is used as prescribed it is not possible to eliminate all residual risk factors. The following hazards may arise in connection with the power tool's construction and design: a) Health defects resulting from vibration emission if the power tool is being used over longer period of time or not adequately managed and properly maintained. b) Injuries and damage to property to due to broken accessories that are suddenly dashed. Warning! This power tool produces an electromagnetic field during operation. This field may under some circumstances interfere with active or passive medical implants. To reduce the risk of serious or fatal injury, we recommend persons with medical implants to consult their physician and the medical implant manufacturer before operating this power tool. SPECIFICATIONS Model No.: Voltage: Frequency: Power input: No-load speed: Impact rate: Drilling capacity: Concrete: Steel: Wood: TH1153216 TH1153216-8 (BS PLUG) Degree of protection / TH1153216S (SAA PLUG) TH1153216-6 (ISRAEL PLUG) 220-240V~ 50/60Hz 1500W 850/min 4400/min 32mm 13mm 40mm TH1153216-9 (INMENTRO PLUG) TH1153216-4 (IRAM PLUG) A 56 1 1a 2 ROTARY HAMMER 4 B 3 The rotary hammer 1pcs rotary hammer 1pcs TOTAL handle 3pcs drill bits (see fig.B) 1pcs flat chisel (see fig.B) 1pcs pointed chisel (see fig.B) 1pcs carrying case 1pcs grease tube 1set carbon brushes 1pcs operating manual 4 6 5 6 6 3 1a 1 3 1 3 1 4 3 1 3 1 4 4 2 2 5 6 5 5 TH1153216,TH1153216S,TH1153216-9, TH1153216-8,TH1153216-6,TH1153216-4 Exploded view TH1153216,TH1153216S,TH1153216-9 TH1153216-8,TH1153216-6,TH1153216-4 Spare part list No. Part Description Qty 1 Rubber Head 1 2 Steel Ring 17.5*2 1 3 Steel frame 1 4 Spring 30.2*1.8*76 1 5 ScrewM5*22 4 6 Washer5 8 7 Washer5 8 8 Cylinder house 1 9 Oil Seal 35*51*6 1 10 Washer 35 1 11 Washer 45*54.5*1 1 12 Bearing 61907 1 13 Ball 7.14 5 14 teleflex 1 15 X-ring 1 16 O-ring 11*2 3 17 Impact hammer 1 18 Ball 7.94 3 19 Cylinder 1 20 Flat key 3*2.5*18 2 21 Ring 45*55*7 1 22 Cylinder Case 50*55*47 1 23 Spring 33.5*3.5*76 1 24 Gamp gear 1 25 Washer 28*1.6 2 26 O-ring 19*3.1 2 27 Rammer 1 28 Washer 1 29 Bearing 30*47*9 1 30 Piston 1 31 Piston Pin 1 32 Connecting Rod 1 33 Gamp 1 34 Screw ST4.8*50 4 35 ScrewM5*20 2 36 Oil Cover 1 37 O-ring 31.5*2 1 No. Part Description Qty 38 Gear Box 1 39 Spring 2 40 Anti-vibration rubber blanket 1 41 Anti-vibration Board 1 42 Screw M8X35 2 43 Screw ST3.9*16 16 44 Gear box right cover 1 45 Gear box right cover 1 46 O-ring 1 47 Knob axle 1 48 Washer 1 49 Knob assembly 1 50 Flat gasket 1 51 Spring washer 3 52 Screw M4*14 1 53 Lock 1 54 Spring 0.6*4.5*17.5 1 55 Oil Seal 19*28*4.5 1 56 Bevel gear 1 57 Washer 1 58 Bearing 1 59 Washer 1 60 Gear 1 61 Ball 8 62 Dead plate 1 63 Washer 1 64 Active plate 1 65 Spring 2 66 Screw 1 67 Bearing 627 1 68 Eccentric shaft 1 69 Bearing 6003 1 70 Washer 17 1 71 Washer 35 1 72 Gear 1 73 Spring W6.8*1.2*33 1 74 Square key 5*5*22 1 No. Part Description Qty 75 Melt 7*19 1 76 Bearing 16*12*10 1 77 Steel Sleeve 1 78 Rubber column 1 79 Ball 4 1 80 Middle Cover 1 81 O-ring W12*1.8 1 82 Dial Twist 1 83 Bearing 1 84 Bearing pressing plate 1 85 Screw M4*14 2 86 Fan Guide 1 87 Rotor 1 88 Screw ST4.8*60 2 89 Stator 1 90 Bearing 608 1 91 Motor housing 1 92 Carbon brush holder 2 93 Carbon brush 2 94 Screw ST3.9*12 2 95 Back cover 1 96 Screw M8*50 1 97 Speed ccontroller(Opition) 1 98 Left handle 1 99 Right handle 1 100 Switch 1 101 Capacitor Option) 1 102 Inductance(Option) 1 103 Screw M8 1 104 Cable board 1 105 Cable sheath 1 106 Cable 1 107 Screw 1 108 Bracket 1 109 Auxiliary handle 1 110 Hoop 1 ROTARY HAMMER www.totalbusiness.com TOTAL TOOLS CO., PTE. LTD. No. 45 Songbei Road, Suzhou Industrial Park, China. MADE IN CHINA T0722.V06 22 PAP