iDatalink MaestroiDatalink Maestro
Account Suspended
Sign in to your accountSign in to your account
Installation Guide for idatalink models including: maestro Rr, Radio Replacement Interface, maestro Rr Radio Replacement Interface, Replacement Interface, Interface, 2019-2022 Subaru Ascent With Amplifier
iDatalink rSU3 Connect an iDatalink-ready receiver and retain steering wheel controls, factory amp and sub, and backup camera in select 2017-up Subaru vehicles at Crutchfield
File Info : application/pdf, 99 Pages, 3.02MB
DocumentDocumentSELECT VEHICLE PRINT PAGES NEEDED HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. 2 Print only the pages for your vehicle using the advanced options in the Print menu. 3 Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or "quick printing" this document will print all of the guides in this compilation. NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. INSTALL GUIDE 2019-2022 SuBaRu aScent WIth aMPlIfIeR RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED iDatalink Maestro RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU3 Installation Harness iDatalink compatible radio OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table SuBaRu aScent WIth aMPlIfIeR 2019-2022 3 4 5 6 7 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS P1/1 STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires from aftermarket radio main harness to the SU3 T-harness and match the wire functions. · Remove the factory radio. Note: only connect purple/white wire to radio reverse input or module damage will occur. STEP 2 · Assemble the SU3 T-harness and connect it to the factory radio harness. STEP 3 · Plug the OBDII connector into the OBDII of the vehicle, under driver dash. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the RCA connectors to the aftermarket radio. · Plug the AUX cable to the aftermarket radio. · Plug the Backup camera cable to the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 5 · Connect all the harnesses to the Maestro RR2 module then test your installation. SuBaRu aScent WIth aMPlIfIeR 2019-2022 Automotive Data Solutions Inc. © 2022 2 ADS-RR(SR)-SUB03-DS-IG-EN 3 maestro.idatalink.com SuBaRu aScent WIth aMPlIfIeR 2019-2022 WIRING DIAGRAM STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK LF RCA INPUT RF RCA INPUT GREEN GREEN/BLACK PURPLE NC PURPLE/BLACK BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) * LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BLUE - POWER ANTENNA SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS * ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR STEP 2 FACTORY RADIO HARNESS STEP 4 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CONNECT TO AFTERMARKET RADIO MAIN HARNESS AUX BACKUP CAM DATA CABLE WIRES FROM VEHICLE NC STEP 3 OBDII CONNECTOR STEP 5 MAESTRO RR2 MODULE SU3 T-HARNESS NOT REQUIRED Automotive Data Solutions Inc. © 2022 STEERING WHEEL CONTROL CABLE AUDIO CABLE ADS-RR(SR)-SUB03-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART SuBaRu aScent WIth aMPlIfIeR 2019-2022 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Reverse Light (+) E-Brake (-) VSS (vehicle speed sensor) (DATA) Power Antenna (+) Orange Purple/White Lt Green Pink Blue N/A Orange/White Yellow/Blue Green/White Blue Orange/White Purple/White Lt Green Pink Blue Orange/White Purple/White Lt Green Pink N/A Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 5 maestro.idatalink.com MODULE DIAGNOSTICS LED 1 PROGRAMMING BUTTON LED 2 SuBaRu aScent WIth aMPlIfIeR 2019-2022 LED 1 LED 1 Module/Firmware status · or · · · · · LED 2 (RR2) Bluetooth activity · · LED STATUS RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes OFF DIAGNOSTIC LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult troubleshooting table. After radio boots up : Normal operation. Bluetooth is activated. Turns off after one minute: Normal operation. Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 6 maestro.idatalink.com TROUBLESHOOTING TABLE SuBaRu aScent WIth aMPlIfIeR 2019-2022 PROBLEM Gauges do not work, radio shows OBD2 Error 1 or Error 2. The light on the Maestro is blinking RED TWICE. The light on the Maestro is flashing RED ONCE. The Harman Kardon system has no sound. (if applicable) SOLUTION Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. There is no firmware on the module; flash the RR module. Ensure the BLUE/WHITE amp turn-on wire is connected. Ensure the 6-pin connector (the plug with blue, green, green/black, purple, and purple/black wires) on the T-harness is not connected to the car. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 7 maestro.idatalink.com INSTALL GUIDE 2019-2022 SuBaRu aScent WIthOut aMPlIfIeR RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED iDatalink Maestro RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU3 Installation Harness iDatalink compatible radio OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table SuBaRu aScent WIthOut aMPlIfIeR 2019-2022 3 4 5 6 7 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS P1/1 STEP 1 · Unbox the aftermarket radio and locate its main harness. · Cut the WHITE and GRAY RCA tips. · Connect the wires from aftermarket radio main harness to the SU3 T-harness and match the wire functions. · Remove the factory radio. Note: only connect purple/white wire to radio reverse input or module damage will occur. STEP 2 · Assemble the SU3 T-harness and connect it to the factory radio harness. STEP 3 · Plug the OBDII connector into the OBDII of the vehicle, under driver dash. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the AUX cable to the aftermarket radio. · Plug the Backup camera cable to the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 5 · Connect all the harnesses to the Maestro RR2 module then test your installation. SuBaRu aScent WIthOut aMPlIfIeR 2019-2022 Automotive Data Solutions Inc. © 2022 1 ADS-RR(SR)-SUB03-DS-IG-EN 3 maestro.idatalink.com SuBaRu aScent WIthOut aMPlIfIeR 2019-2022 WIRING DIAGRAM STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) * LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BLUE - POWER ANTENNA SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS * ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR STEP 2 FACTORY RADIO HARNESS STEP 4 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CONNECT TO AFTERMARKET RADIO MAIN HARNESS AUX BACKUP CAM DATA CABLE WIRES FROM VEHICLE STEP 3 OBDII CONNECTOR STEP 5 MAESTRO RR2 MODULE SU3 T-HARNESS NOT REQUIRED Automotive Data Solutions Inc. © 2022 STEERING WHEEL CONTROL CABLE AUDIO CABLE ADS-RR(SR)-SUB03-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART SuBaRu aScent WIthOut aMPlIfIeR 2019-2022 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Reverse Light (+) E-Brake (-) VSS (vehicle speed sensor) (DATA) Power Antenna (+) Orange Purple/White Lt Green Pink Blue N/A Orange/White Yellow/Blue Green/White Blue Orange/White Purple/White Lt Green Pink Blue Orange/White Purple/White Lt Green Pink N/A Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 5 maestro.idatalink.com MODULE DIAGNOSTICS LED 1 PROGRAMMING BUTTON LED 2 SuBaRu aScent WIthOut aMPlIfIeR 2019-2022 LED 1 LED 1 Module/Firmware status · or · · · · · LED 2 (RR2) Bluetooth activity · · LED STATUS RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes OFF DIAGNOSTIC LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult troubleshooting table. After radio boots up : Normal operation. Bluetooth is activated. Turns off after one minute: Normal operation. Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 6 maestro.idatalink.com TROUBLESHOOTING TABLE SuBaRu aScent WIthOut aMPlIfIeR 2019-2022 PROBLEM Gauges do not work, radio shows OBD2 Error 1 or Error 2. The light on the Maestro is blinking RED TWICE. The light on the Maestro is flashing RED ONCE. The Harman Kardon system has no sound. (if applicable) SOLUTION Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. There is no firmware on the module; flash the RR module. Ensure the BLUE/WHITE amp turn-on wire is connected. Ensure the 6-pin connector (the plug with blue, green, green/black, purple, and purple/black wires) on the T-harness is not connected to the car. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 7 maestro.idatalink.com INSTALL GUIDE 2018-2022 SuBaRu cROSStRek WIth aMPlIfIeR RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED iDatalink Maestro RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU3 Installation Harness iDatalink compatible radio OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table SuBaRu cROSStRek WIth aMPlIfIeR 2018-2022 3 4 5 6 7 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS P1/1 STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires from aftermarket radio main harness to the SU3 T-harness and match the wire functions. · Remove the factory radio. Note: only connect purple/white wire to radio reverse input or module damage will occur. STEP 2 · Assemble the SU3 T-harness and connect it to the factory radio harness. STEP 3 · Plug the OBDII connector into the OBDII of the vehicle, under driver dash. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the RCA connectors to the aftermarket radio. · Plug the AUX cable to the aftermarket radio. · Plug the Backup camera cable to the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 5 · Connect all the harnesses to the Maestro RR2 module then test your installation. SuBaRu cROSStRek WIth aMPlIfIeR 2018-2022 Automotive Data Solutions Inc. © 2022 2 ADS-RR(SR)-SUB03-DS-IG-EN 3 maestro.idatalink.com SuBaRu cROSStRek WIth aMPlIfIeR 2018-2022 WIRING DIAGRAM STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK LF RCA INPUT RF RCA INPUT GREEN GREEN/BLACK PURPLE NC PURPLE/BLACK BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) * LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BLUE - POWER ANTENNA SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS * ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR STEP 2 FACTORY RADIO HARNESS STEP 4 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CONNECT TO AFTERMARKET RADIO MAIN HARNESS AUX BACKUP CAM DATA CABLE WIRES FROM VEHICLE NC STEP 3 OBDII CONNECTOR STEP 5 MAESTRO RR2 MODULE SU3 T-HARNESS NOT REQUIRED Automotive Data Solutions Inc. © 2022 STEERING WHEEL CONTROL CABLE AUDIO CABLE ADS-RR(SR)-SUB03-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART SuBaRu cROSStRek WIth aMPlIfIeR 2018-2022 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Reverse Light (+) E-Brake (-) VSS (vehicle speed sensor) (DATA) Power Antenna (+) Orange Purple/White Lt Green Pink Blue N/A Orange/White Yellow/Blue Green/White Blue Orange/White Purple/White Lt Green Pink Blue Orange/White Purple/White Lt Green Pink N/A Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 5 maestro.idatalink.com MODULE DIAGNOSTICS LED 1 PROGRAMMING BUTTON LED 2 SuBaRu cROSStRek WIth aMPlIfIeR 2018-2022 LED 1 LED 1 Module/Firmware status · or · · · · · LED 2 (RR2) Bluetooth activity · · LED STATUS RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes OFF DIAGNOSTIC LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult troubleshooting table. After radio boots up : Normal operation. Bluetooth is activated. Turns off after one minute: Normal operation. Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 6 maestro.idatalink.com TROUBLESHOOTING TABLE SuBaRu cROSStRek WIth aMPlIfIeR 2018-2022 PROBLEM Gauges do not work, radio shows OBD2 Error 1 or Error 2. The light on the Maestro is blinking RED TWICE. The light on the Maestro is flashing RED ONCE. The Harman Kardon system has no sound. (if applicable) SOLUTION Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. There is no firmware on the module; flash the RR module. Ensure the BLUE/WHITE amp turn-on wire is connected. Ensure the 6-pin connector (the plug with blue, green, green/black, purple, and purple/black wires) on the T-harness is not connected to the car. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 7 maestro.idatalink.com INSTALL GUIDE 2018-2022 SuBaRu cROSStRek WIthOut aMPlIfIeR RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED iDatalink Maestro RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU3 Installation Harness iDatalink compatible radio OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table SuBaRu cROSStRek WIthOut aMPlIfIeR 2018-2022 3 4 5 6 7 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS P1/1 STEP 1 · Unbox the aftermarket radio and locate its main harness. · Cut the WHITE and GRAY RCA tips. · Connect the wires from aftermarket radio main harness to the SU3 T-harness and match the wire functions. · Remove the factory radio. Note: only connect purple/white wire to radio reverse input or module damage will occur. STEP 2 · Assemble the SU3 T-harness and connect it to the factory radio harness. STEP 3 · Plug the OBDII connector into the OBDII of the vehicle, under driver dash. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the AUX cable to the aftermarket radio. · Plug the Backup camera cable to the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 5 · Connect all the harnesses to the Maestro RR2 module then test your installation. SuBaRu cROSStRek WIthOut aMPlIfIeR 2018-2022 Automotive Data Solutions Inc. © 2022 1 ADS-RR(SR)-SUB03-DS-IG-EN 3 maestro.idatalink.com SuBaRu cROSStRek WIthOut aMPlIfIeR 2018-2022 WIRING DIAGRAM STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) * LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BLUE - POWER ANTENNA SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS * ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR STEP 2 FACTORY RADIO HARNESS STEP 4 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CONNECT TO AFTERMARKET RADIO MAIN HARNESS AUX BACKUP CAM DATA CABLE WIRES FROM VEHICLE STEP 3 OBDII CONNECTOR STEP 5 MAESTRO RR2 MODULE SU3 T-HARNESS NOT REQUIRED Automotive Data Solutions Inc. © 2022 STEERING WHEEL CONTROL CABLE AUDIO CABLE ADS-RR(SR)-SUB03-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART SuBaRu cROSStRek WIthOut aMPlIfIeR 2018-2022 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Reverse Light (+) E-Brake (-) VSS (vehicle speed sensor) (DATA) Power Antenna (+) Orange Purple/White Lt Green Pink Blue N/A Orange/White Yellow/Blue Green/White Blue Orange/White Purple/White Lt Green Pink Blue Orange/White Purple/White Lt Green Pink N/A Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 5 maestro.idatalink.com MODULE DIAGNOSTICS LED 1 PROGRAMMING BUTTON LED 2 SuBaRu cROSStRek WIthOut aMPlIfIeR 2018-2022 LED 1 LED 1 Module/Firmware status · or · · · · · LED 2 (RR2) Bluetooth activity · · LED STATUS RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes OFF DIAGNOSTIC LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult troubleshooting table. After radio boots up : Normal operation. Bluetooth is activated. Turns off after one minute: Normal operation. Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 6 maestro.idatalink.com TROUBLESHOOTING TABLE SuBaRu cROSStRek WIthOut aMPlIfIeR 2018-2022 PROBLEM Gauges do not work, radio shows OBD2 Error 1 or Error 2. The light on the Maestro is blinking RED TWICE. The light on the Maestro is flashing RED ONCE. The Harman Kardon system has no sound. (if applicable) SOLUTION Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. There is no firmware on the module; flash the RR module. Ensure the BLUE/WHITE amp turn-on wire is connected. Ensure the 6-pin connector (the plug with blue, green, green/black, purple, and purple/black wires) on the T-harness is not connected to the car. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 7 maestro.idatalink.com INSTALL GUIDE 2019-2022 SuBaRu fOReSteR WIth aMPlIfIeR RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED iDatalink Maestro RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU3 Installation Harness iDatalink compatible radio OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table SuBaRu fOReSteR WIth aMPlIfIeR 2019-2022 3 4 5 6 7 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS P1/1 STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires from aftermarket radio main harness to the SU3 T-harness and match the wire functions. · Remove the factory radio. Note: only connect purple/white wire to radio reverse input or module damage will occur. STEP 2 · Assemble the SU3 T-harness and connect it to the factory radio harness. STEP 3 · Plug the OBDII connector into the OBDII of the vehicle, under driver dash. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the RCA connectors to the aftermarket radio. · Plug the AUX cable to the aftermarket radio. · Plug the Backup camera cable to the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 5 · Connect all the harnesses to the Maestro RR2 module then test your installation. SuBaRu fOReSteR WIth aMPlIfIeR 2019-2022 Automotive Data Solutions Inc. © 2022 2 ADS-RR(SR)-SUB03-DS-IG-EN 3 maestro.idatalink.com SuBaRu fOReSteR WIth aMPlIfIeR 2019-2022 WIRING DIAGRAM STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK LF RCA INPUT RF RCA INPUT GREEN GREEN/BLACK PURPLE NC PURPLE/BLACK BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) * LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BLUE - POWER ANTENNA SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS * ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR STEP 2 FACTORY RADIO HARNESS STEP 4 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CONNECT TO AFTERMARKET RADIO MAIN HARNESS AUX BACKUP CAM DATA CABLE WIRES FROM VEHICLE NC STEP 3 OBDII CONNECTOR STEP 5 MAESTRO RR2 MODULE SU3 T-HARNESS NOT REQUIRED Automotive Data Solutions Inc. © 2022 STEERING WHEEL CONTROL CABLE AUDIO CABLE ADS-RR(SR)-SUB03-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART SuBaRu fOReSteR WIth aMPlIfIeR 2019-2022 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Reverse Light (+) E-Brake (-) VSS (vehicle speed sensor) (DATA) Power Antenna (+) Orange Purple/White Lt Green Pink Blue N/A Orange/White Yellow/Blue Green/White Blue Orange/White Purple/White Lt Green Pink Blue Orange/White Purple/White Lt Green Pink N/A Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 5 maestro.idatalink.com MODULE DIAGNOSTICS LED 1 PROGRAMMING BUTTON LED 2 SuBaRu fOReSteR WIth aMPlIfIeR 2019-2022 LED 1 LED 1 Module/Firmware status · or · · · · · LED 2 (RR2) Bluetooth activity · · LED STATUS RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes OFF DIAGNOSTIC LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult troubleshooting table. After radio boots up : Normal operation. Bluetooth is activated. Turns off after one minute: Normal operation. Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 6 maestro.idatalink.com TROUBLESHOOTING TABLE SuBaRu fOReSteR WIth aMPlIfIeR 2019-2022 PROBLEM Gauges do not work, radio shows OBD2 Error 1 or Error 2. The light on the Maestro is blinking RED TWICE. The light on the Maestro is flashing RED ONCE. The Harman Kardon system has no sound. (if applicable) SOLUTION Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. There is no firmware on the module; flash the RR module. Ensure the BLUE/WHITE amp turn-on wire is connected. Ensure the 6-pin connector (the plug with blue, green, green/black, purple, and purple/black wires) on the T-harness is not connected to the car. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 7 maestro.idatalink.com INSTALL GUIDE 2019-2022 SuBaRu fOReSteR WIthOut aMPlIfIeR RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED iDatalink Maestro RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU3 Installation Harness iDatalink compatible radio OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table SuBaRu fOReSteR WIthOut aMPlIfIeR 2019-2022 3 4 5 6 7 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS P1/1 STEP 1 · Unbox the aftermarket radio and locate its main harness. · Cut the WHITE and GRAY RCA tips. · Connect the wires from aftermarket radio main harness to the SU3 T-harness and match the wire functions. · Remove the factory radio. Note: only connect purple/white wire to radio reverse input or module damage will occur. STEP 2 · Assemble the SU3 T-harness and connect it to the factory radio harness. STEP 3 · Plug the OBDII connector into the OBDII of the vehicle, under driver dash. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the AUX cable to the aftermarket radio. · Plug the Backup camera cable to the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 5 · Connect all the harnesses to the Maestro RR2 module then test your installation. SuBaRu fOReSteR WIthOut aMPlIfIeR 2019-2022 Automotive Data Solutions Inc. © 2022 1 ADS-RR(SR)-SUB03-DS-IG-EN 3 maestro.idatalink.com SuBaRu fOReSteR WIthOut aMPlIfIeR 2019-2022 WIRING DIAGRAM STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) * LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BLUE - POWER ANTENNA SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS * ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR STEP 2 FACTORY RADIO HARNESS STEP 4 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CONNECT TO AFTERMARKET RADIO MAIN HARNESS AUX BACKUP CAM DATA CABLE WIRES FROM VEHICLE STEP 3 OBDII CONNECTOR STEP 5 MAESTRO RR2 MODULE SU3 T-HARNESS NOT REQUIRED Automotive Data Solutions Inc. © 2022 STEERING WHEEL CONTROL CABLE AUDIO CABLE ADS-RR(SR)-SUB03-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART SuBaRu fOReSteR WIthOut aMPlIfIeR 2019-2022 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Reverse Light (+) E-Brake (-) VSS (vehicle speed sensor) (DATA) Power Antenna (+) Orange Purple/White Lt Green Pink Blue N/A Orange/White Yellow/Blue Green/White Blue Orange/White Purple/White Lt Green Pink Blue Orange/White Purple/White Lt Green Pink N/A Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 5 maestro.idatalink.com MODULE DIAGNOSTICS LED 1 PROGRAMMING BUTTON LED 2 SuBaRu fOReSteR WIthOut aMPlIfIeR 2019-2022 LED 1 LED 1 Module/Firmware status · or · · · · · LED 2 (RR2) Bluetooth activity · · LED STATUS RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes OFF DIAGNOSTIC LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult troubleshooting table. After radio boots up : Normal operation. Bluetooth is activated. Turns off after one minute: Normal operation. Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 6 maestro.idatalink.com TROUBLESHOOTING TABLE SuBaRu fOReSteR WIthOut aMPlIfIeR 2019-2022 PROBLEM Gauges do not work, radio shows OBD2 Error 1 or Error 2. The light on the Maestro is blinking RED TWICE. The light on the Maestro is flashing RED ONCE. The Harman Kardon system has no sound. (if applicable) SOLUTION Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. There is no firmware on the module; flash the RR module. Ensure the BLUE/WHITE amp turn-on wire is connected. Ensure the 6-pin connector (the plug with blue, green, green/black, purple, and purple/black wires) on the T-harness is not connected to the car. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 7 maestro.idatalink.com INSTALL GUIDE 2017-2022 SuBaRu IMPReza WIth aMPlIfIeR RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED iDatalink Maestro RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU3 Installation Harness iDatalink compatible radio OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table SuBaRu IMPReza WIth aMPlIfIeR 2017-2022 3 4 5 6 7 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS P1/1 STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires from aftermarket radio main harness to the SU3 T-harness and match the wire functions. · Remove the factory radio. Note: only connect purple/white wire to radio reverse input or module damage will occur. STEP 2 · Assemble the SU3 T-harness and connect it to the factory radio harness. STEP 3 · Plug the OBDII connector into the OBDII of the vehicle, under driver dash. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the RCA connectors to the aftermarket radio. · Plug the AUX cable to the aftermarket radio. · Plug the Backup camera cable to the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 5 · Connect all the harnesses to the Maestro RR2 module then test your installation. SuBaRu IMPReza WIth aMPlIfIeR 2017-2022 Automotive Data Solutions Inc. © 2022 2 ADS-RR(SR)-SUB03-DS-IG-EN 3 maestro.idatalink.com SuBaRu IMPReza WIth aMPlIfIeR 2017-2022 WIRING DIAGRAM STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK LF RCA INPUT RF RCA INPUT GREEN GREEN/BLACK PURPLE NC PURPLE/BLACK BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) * LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BLUE - POWER ANTENNA SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS * ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR STEP 2 FACTORY RADIO HARNESS STEP 4 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CONNECT TO AFTERMARKET RADIO MAIN HARNESS AUX BACKUP CAM DATA CABLE WIRES FROM VEHICLE NC STEP 3 OBDII CONNECTOR STEP 5 MAESTRO RR2 MODULE SU3 T-HARNESS NOT REQUIRED Automotive Data Solutions Inc. © 2022 STEERING WHEEL CONTROL CABLE AUDIO CABLE ADS-RR(SR)-SUB03-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART SuBaRu IMPReza WIth aMPlIfIeR 2017-2022 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Reverse Light (+) E-Brake (-) VSS (vehicle speed sensor) (DATA) Power Antenna (+) Orange Purple/White Lt Green Pink Blue N/A Orange/White Yellow/Blue Green/White Blue Orange/White Purple/White Lt Green Pink Blue Orange/White Purple/White Lt Green Pink N/A Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 5 maestro.idatalink.com MODULE DIAGNOSTICS LED 1 PROGRAMMING BUTTON LED 2 SuBaRu IMPReza WIth aMPlIfIeR 2017-2022 LED 1 LED 1 Module/Firmware status · or · · · · · LED 2 (RR2) Bluetooth activity · · LED STATUS RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes OFF DIAGNOSTIC LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult troubleshooting table. After radio boots up : Normal operation. Bluetooth is activated. Turns off after one minute: Normal operation. Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 6 maestro.idatalink.com TROUBLESHOOTING TABLE SuBaRu IMPReza WIth aMPlIfIeR 2017-2022 PROBLEM Gauges do not work, radio shows OBD2 Error 1 or Error 2. The light on the Maestro is blinking RED TWICE. The light on the Maestro is flashing RED ONCE. The Harman Kardon system has no sound. (if applicable) SOLUTION Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. There is no firmware on the module; flash the RR module. Ensure the BLUE/WHITE amp turn-on wire is connected. Ensure the 6-pin connector (the plug with blue, green, green/black, purple, and purple/black wires) on the T-harness is not connected to the car. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 7 maestro.idatalink.com INSTALL GUIDE 2017-2022 SuBaRu IMPReza WIthOut aMPlIfIeR RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED iDatalink Maestro RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU3 Installation Harness iDatalink compatible radio OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table SuBaRu IMPReza WIthOut aMPlIfIeR 2017-2022 3 4 5 6 7 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS P1/1 STEP 1 · Unbox the aftermarket radio and locate its main harness. · Cut the WHITE and GRAY RCA tips. · Connect the wires from aftermarket radio main harness to the SU3 T-harness and match the wire functions. · Remove the factory radio. Note: only connect purple/white wire to radio reverse input or module damage will occur. STEP 2 · Assemble the SU3 T-harness and connect it to the factory radio harness. STEP 3 · Plug the OBDII connector into the OBDII of the vehicle, under driver dash. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the AUX cable to the aftermarket radio. · Plug the Backup camera cable to the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 5 · Connect all the harnesses to the Maestro RR2 module then test your installation. SuBaRu IMPReza WIthOut aMPlIfIeR 2017-2022 Automotive Data Solutions Inc. © 2022 1 ADS-RR(SR)-SUB03-DS-IG-EN 3 maestro.idatalink.com SuBaRu IMPReza WIthOut aMPlIfIeR 2017-2022 WIRING DIAGRAM STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) * LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BLUE - POWER ANTENNA SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS * ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR STEP 2 FACTORY RADIO HARNESS STEP 4 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CONNECT TO AFTERMARKET RADIO MAIN HARNESS AUX BACKUP CAM DATA CABLE WIRES FROM VEHICLE STEP 3 OBDII CONNECTOR STEP 5 MAESTRO RR2 MODULE SU3 T-HARNESS NOT REQUIRED Automotive Data Solutions Inc. © 2022 STEERING WHEEL CONTROL CABLE AUDIO CABLE ADS-RR(SR)-SUB03-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART SuBaRu IMPReza WIthOut aMPlIfIeR 2017-2022 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Reverse Light (+) E-Brake (-) VSS (vehicle speed sensor) (DATA) Power Antenna (+) Orange Purple/White Lt Green Pink Blue N/A Orange/White Yellow/Blue Green/White Blue Orange/White Purple/White Lt Green Pink Blue Orange/White Purple/White Lt Green Pink N/A Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 5 maestro.idatalink.com MODULE DIAGNOSTICS LED 1 PROGRAMMING BUTTON LED 2 SuBaRu IMPReza WIthOut aMPlIfIeR 2017-2022 LED 1 LED 1 Module/Firmware status · or · · · · · LED 2 (RR2) Bluetooth activity · · LED STATUS RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes OFF DIAGNOSTIC LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult troubleshooting table. After radio boots up : Normal operation. Bluetooth is activated. Turns off after one minute: Normal operation. Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 6 maestro.idatalink.com TROUBLESHOOTING TABLE SuBaRu IMPReza WIthOut aMPlIfIeR 2017-2022 PROBLEM Gauges do not work, radio shows OBD2 Error 1 or Error 2. The light on the Maestro is blinking RED TWICE. The light on the Maestro is flashing RED ONCE. The Harman Kardon system has no sound. (if applicable) SOLUTION Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. There is no firmware on the module; flash the RR module. Ensure the BLUE/WHITE amp turn-on wire is connected. Ensure the 6-pin connector (the plug with blue, green, green/black, purple, and purple/black wires) on the T-harness is not connected to the car. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 7 maestro.idatalink.com INSTALL GUIDE 2018-2022 SuBaRu legacy WIth aMPlIfIeR RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED iDatalink Maestro RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU3 Installation Harness iDatalink compatible radio OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table SuBaRu legacy WIth aMPlIfIeR 2018-2022 3 4 5 6 7 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS P1/1 STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires from aftermarket radio main harness to the SU3 T-harness and match the wire functions. · Remove the factory radio. Note: only connect purple/white wire to radio reverse input or module damage will occur. STEP 2 · Assemble the SU3 T-harness and connect it to the factory radio harness. STEP 3 · Plug the OBDII connector into the OBDII of the vehicle, under driver dash. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the RCA connectors to the aftermarket radio. · Plug the AUX cable to the aftermarket radio. · Plug the Backup camera cable to the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 5 · Connect all the harnesses to the Maestro RR2 module then test your installation. SuBaRu legacy WIth aMPlIfIeR 2018-2022 Automotive Data Solutions Inc. © 2022 2 ADS-RR(SR)-SUB03-DS-IG-EN 3 maestro.idatalink.com SuBaRu legacy WIth aMPlIfIeR 2018-2022 WIRING DIAGRAM STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK LF RCA INPUT RF RCA INPUT GREEN GREEN/BLACK PURPLE NC PURPLE/BLACK BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) * LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BLUE - POWER ANTENNA SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS * ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR STEP 2 FACTORY RADIO HARNESS STEP 4 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CONNECT TO AFTERMARKET RADIO MAIN HARNESS AUX BACKUP CAM DATA CABLE WIRES FROM VEHICLE NC STEP 3 OBDII CONNECTOR STEP 5 MAESTRO RR2 MODULE SU3 T-HARNESS NOT REQUIRED Automotive Data Solutions Inc. © 2022 STEERING WHEEL CONTROL CABLE AUDIO CABLE ADS-RR(SR)-SUB03-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART SuBaRu legacy WIth aMPlIfIeR 2018-2022 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Reverse Light (+) E-Brake (-) VSS (vehicle speed sensor) (DATA) Power Antenna (+) Orange Purple/White Lt Green Pink Blue N/A Orange/White Yellow/Blue Green/White Blue Orange/White Purple/White Lt Green Pink Blue Orange/White Purple/White Lt Green Pink N/A Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 5 maestro.idatalink.com MODULE DIAGNOSTICS LED 1 PROGRAMMING BUTTON LED 2 SuBaRu legacy WIth aMPlIfIeR 2018-2022 LED 1 LED 1 Module/Firmware status · or · · · · · LED 2 (RR2) Bluetooth activity · · LED STATUS RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes OFF DIAGNOSTIC LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult troubleshooting table. After radio boots up : Normal operation. Bluetooth is activated. Turns off after one minute: Normal operation. Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 6 maestro.idatalink.com TROUBLESHOOTING TABLE SuBaRu legacy WIth aMPlIfIeR 2018-2022 PROBLEM Gauges do not work, radio shows OBD2 Error 1 or Error 2. The light on the Maestro is blinking RED TWICE. The light on the Maestro is flashing RED ONCE. The Harman Kardon system has no sound. (if applicable) SOLUTION Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. There is no firmware on the module; flash the RR module. Ensure the BLUE/WHITE amp turn-on wire is connected. Ensure the 6-pin connector (the plug with blue, green, green/black, purple, and purple/black wires) on the T-harness is not connected to the car. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 7 maestro.idatalink.com INSTALL GUIDE 2018-2022 SuBaRu legacy WIthOut aMPlIfIeR RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED iDatalink Maestro RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU3 Installation Harness iDatalink compatible radio OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table SuBaRu legacy WIthOut aMPlIfIeR 2018-2022 3 4 5 6 7 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS P1/1 STEP 1 · Unbox the aftermarket radio and locate its main harness. · Cut the WHITE and GRAY RCA tips. · Connect the wires from aftermarket radio main harness to the SU3 T-harness and match the wire functions. · Remove the factory radio. Note: only connect purple/white wire to radio reverse input or module damage will occur. STEP 2 · Assemble the SU3 T-harness and connect it to the factory radio harness. STEP 3 · Plug the OBDII connector into the OBDII of the vehicle, under driver dash. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the AUX cable to the aftermarket radio. · Plug the Backup camera cable to the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 5 · Connect all the harnesses to the Maestro RR2 module then test your installation. SuBaRu legacy WIthOut aMPlIfIeR 2018-2022 Automotive Data Solutions Inc. © 2022 1 ADS-RR(SR)-SUB03-DS-IG-EN 3 maestro.idatalink.com SuBaRu legacy WIthOut aMPlIfIeR 2018-2022 WIRING DIAGRAM STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) * LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BLUE - POWER ANTENNA SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS * ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR STEP 2 FACTORY RADIO HARNESS STEP 4 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CONNECT TO AFTERMARKET RADIO MAIN HARNESS AUX BACKUP CAM DATA CABLE WIRES FROM VEHICLE STEP 3 OBDII CONNECTOR STEP 5 MAESTRO RR2 MODULE SU3 T-HARNESS NOT REQUIRED Automotive Data Solutions Inc. © 2022 STEERING WHEEL CONTROL CABLE AUDIO CABLE ADS-RR(SR)-SUB03-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART SuBaRu legacy WIthOut aMPlIfIeR 2018-2022 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Reverse Light (+) E-Brake (-) VSS (vehicle speed sensor) (DATA) Power Antenna (+) Orange Purple/White Lt Green Pink Blue N/A Orange/White Yellow/Blue Green/White Blue Orange/White Purple/White Lt Green Pink Blue Orange/White Purple/White Lt Green Pink N/A Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 5 maestro.idatalink.com MODULE DIAGNOSTICS LED 1 PROGRAMMING BUTTON LED 2 SuBaRu legacy WIthOut aMPlIfIeR 2018-2022 LED 1 LED 1 Module/Firmware status · or · · · · · LED 2 (RR2) Bluetooth activity · · LED STATUS RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes OFF DIAGNOSTIC LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult troubleshooting table. After radio boots up : Normal operation. Bluetooth is activated. Turns off after one minute: Normal operation. Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 6 maestro.idatalink.com TROUBLESHOOTING TABLE SuBaRu legacy WIthOut aMPlIfIeR 2018-2022 PROBLEM Gauges do not work, radio shows OBD2 Error 1 or Error 2. The light on the Maestro is blinking RED TWICE. The light on the Maestro is flashing RED ONCE. The Harman Kardon system has no sound. (if applicable) SOLUTION Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. There is no firmware on the module; flash the RR module. Ensure the BLUE/WHITE amp turn-on wire is connected. Ensure the 6-pin connector (the plug with blue, green, green/black, purple, and purple/black wires) on the T-harness is not connected to the car. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 7 maestro.idatalink.com INSTALL GUIDE 2018-2022 SuBaRu OutBack WIth aMPlIfIeR RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED iDatalink Maestro RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU3 Installation Harness iDatalink compatible radio OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table SuBaRu OutBack WIth aMPlIfIeR 2018-2022 3 4 5 6 7 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS P1/1 STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires from aftermarket radio main harness to the SU3 T-harness and match the wire functions. · Remove the factory radio. Note: only connect purple/white wire to radio reverse input or module damage will occur. STEP 2 · Assemble the SU3 T-harness and connect it to the factory radio harness. STEP 3 · Plug the OBDII connector into the OBDII of the vehicle, under driver dash. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the RCA connectors to the aftermarket radio. · Plug the AUX cable to the aftermarket radio. · Plug the Backup camera cable to the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 5 · Connect all the harnesses to the Maestro RR2 module then test your installation. SuBaRu OutBack WIth aMPlIfIeR 2018-2022 Automotive Data Solutions Inc. © 2022 2 ADS-RR(SR)-SUB03-DS-IG-EN 3 maestro.idatalink.com SuBaRu OutBack WIth aMPlIfIeR 2018-2022 WIRING DIAGRAM STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK LF RCA INPUT RF RCA INPUT GREEN GREEN/BLACK PURPLE NC PURPLE/BLACK BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) * LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BLUE - POWER ANTENNA SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS * ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR STEP 2 FACTORY RADIO HARNESS STEP 4 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CONNECT TO AFTERMARKET RADIO MAIN HARNESS AUX BACKUP CAM DATA CABLE WIRES FROM VEHICLE NC STEP 3 OBDII CONNECTOR STEP 5 MAESTRO RR2 MODULE SU3 T-HARNESS NOT REQUIRED Automotive Data Solutions Inc. © 2022 STEERING WHEEL CONTROL CABLE AUDIO CABLE ADS-RR(SR)-SUB03-DS-IG-EN 2 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART SuBaRu OutBack WIth aMPlIfIeR 2018-2022 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Reverse Light (+) E-Brake (-) VSS (vehicle speed sensor) (DATA) Power Antenna (+) Orange Purple/White Lt Green Pink Blue N/A Orange/White Yellow/Blue Green/White Blue Orange/White Purple/White Lt Green Pink Blue Orange/White Purple/White Lt Green Pink N/A Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 5 maestro.idatalink.com MODULE DIAGNOSTICS LED 1 PROGRAMMING BUTTON LED 2 SuBaRu OutBack WIth aMPlIfIeR 2018-2022 LED 1 LED 1 Module/Firmware status · or · · · · · LED 2 (RR2) Bluetooth activity · · LED STATUS RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes OFF DIAGNOSTIC LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult troubleshooting table. After radio boots up : Normal operation. Bluetooth is activated. Turns off after one minute: Normal operation. Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 6 maestro.idatalink.com TROUBLESHOOTING TABLE SuBaRu OutBack WIth aMPlIfIeR 2018-2022 PROBLEM Gauges do not work, radio shows OBD2 Error 1 or Error 2. The light on the Maestro is blinking RED TWICE. The light on the Maestro is flashing RED ONCE. The Harman Kardon system has no sound. (if applicable) SOLUTION Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. There is no firmware on the module; flash the RR module. Ensure the BLUE/WHITE amp turn-on wire is connected. Ensure the 6-pin connector (the plug with blue, green, green/black, purple, and purple/black wires) on the T-harness is not connected to the car. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 7 maestro.idatalink.com INSTALL GUIDE 2018-2022 SuBaRu OutBack WIthOut aMPlIfIeR RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED iDatalink Maestro RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU3 Installation Harness iDatalink compatible radio OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table SuBaRu OutBack WIthOut aMPlIfIeR 2018-2022 3 4 5 6 7 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS P1/1 STEP 1 · Unbox the aftermarket radio and locate its main harness. · Cut the WHITE and GRAY RCA tips. · Connect the wires from aftermarket radio main harness to the SU3 T-harness and match the wire functions. · Remove the factory radio. Note: only connect purple/white wire to radio reverse input or module damage will occur. STEP 2 · Assemble the SU3 T-harness and connect it to the factory radio harness. STEP 3 · Plug the OBDII connector into the OBDII of the vehicle, under driver dash. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the AUX cable to the aftermarket radio. · Plug the Backup camera cable to the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 5 · Connect all the harnesses to the Maestro RR2 module then test your installation. SuBaRu OutBack WIthOut aMPlIfIeR 2018-2022 Automotive Data Solutions Inc. © 2022 1 ADS-RR(SR)-SUB03-DS-IG-EN 3 maestro.idatalink.com SuBaRu OutBack WIthOut aMPlIfIeR 2018-2022 WIRING DIAGRAM STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) * LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BLUE - POWER ANTENNA SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS * ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR STEP 2 FACTORY RADIO HARNESS STEP 4 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CONNECT TO AFTERMARKET RADIO MAIN HARNESS AUX BACKUP CAM DATA CABLE WIRES FROM VEHICLE STEP 3 OBDII CONNECTOR STEP 5 MAESTRO RR2 MODULE SU3 T-HARNESS NOT REQUIRED Automotive Data Solutions Inc. © 2022 STEERING WHEEL CONTROL CABLE AUDIO CABLE ADS-RR(SR)-SUB03-DS-IG-EN 1 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART SuBaRu OutBack WIthOut aMPlIfIeR 2018-2022 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Reverse Light (+) E-Brake (-) VSS (vehicle speed sensor) (DATA) Power Antenna (+) Orange Purple/White Lt Green Pink Blue N/A Orange/White Yellow/Blue Green/White Blue Orange/White Purple/White Lt Green Pink Blue Orange/White Purple/White Lt Green Pink N/A Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 5 maestro.idatalink.com MODULE DIAGNOSTICS LED 1 PROGRAMMING BUTTON LED 2 SuBaRu OutBack WIthOut aMPlIfIeR 2018-2022 LED 1 LED 1 Module/Firmware status · or · · · · · LED 2 (RR2) Bluetooth activity · · LED STATUS RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes OFF DIAGNOSTIC LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult troubleshooting table. After radio boots up : Normal operation. Bluetooth is activated. Turns off after one minute: Normal operation. Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 6 maestro.idatalink.com TROUBLESHOOTING TABLE SuBaRu OutBack WIthOut aMPlIfIeR 2018-2022 PROBLEM Gauges do not work, radio shows OBD2 Error 1 or Error 2. The light on the Maestro is blinking RED TWICE. The light on the Maestro is flashing RED ONCE. The Harman Kardon system has no sound. (if applicable) SOLUTION Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. There is no firmware on the module; flash the RR module. Ensure the BLUE/WHITE amp turn-on wire is connected. Ensure the 6-pin connector (the plug with blue, green, green/black, purple, and purple/black wires) on the T-harness is not connected to the car. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 7 maestro.idatalink.com INSTALL GUIDE 2019-2021 SuBaRu WRX StI WIth aMPlIfIeR RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED iDatalink Maestro RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU3 Installation Harness iDatalink compatible radio OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table SuBaRu WRX StI WIth aMPlIfIeR 2019-2021 3 4 5 6 7 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS P1/1 STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires from aftermarket radio main harness to the SU3 T-harness and match the wire functions. · Remove the factory radio. Note: only connect purple/white wire to radio reverse input or module damage will occur. STEP 2 · Assemble the SU3 T-harness and connect it to the factory radio harness. · Locate the 28 pin connector on the SU3 T-harness. Cut the Brown/Red wire (pin 9), extend and connect it to the Red wire (pin1) of the 40 pin climate control connector. Cut the Brown/Yellow wire (pin 10), extend and connect it to the Blue wire (pin2) of the 40 pin climate control connector. STEP 3 · Plug the OBDII connector into the OBDII of the vehicle, under driver dash. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the RCA connectors to the aftermarket radio. · Plug the AUX cable to the aftermarket radio. · Plug the Backup camera cable to the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 5 · Connect all the harnesses to the Maestro RR2 module then test your installation. Automotive Data Solutions Inc. © 2022 3 ADS-RR(SR)-SUB03-DS-IG-EN SuBaRu WRX StI WIth aMPlIfIeR 2019-2021 3 maestro.idatalink.com SuBaRu WRX StI WIth aMPlIfIeR 2019-2021 WIRING DIAGRAM STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK LF RCA INPUT RF RCA INPUT GREEN GREEN/BLACK PURPLE NC PURPLE/BLACK BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) * LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BLUE - POWER ANTENNA SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS * ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR STEP 2 FACTORY RADIO HARNESS STEP 4 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CONNECT TO AFTERMARKET RADIO MAIN HARNESS AUX BACKUP CAM DATA CABLE WIRES FROM NC VEHICLE CUT AND ISOLATE BROWN/RED WIRE (PIN 9) BROWN/YELLOW WIRE (PIN 10) BROWN/RED BROWN/YELLOW STEP 3 CLIMATE CONTROL CONNECTOR RED 12 BLUE OBDII CONNECTOR STEP 5 MAESTRO RR2 MODULE SU3 T-HARNESS NOT REQUIRED Automotive Data Solutions Inc. © 2022 STEERING WHEEL CONTROL CABLE AUDIO CABLE ADS-RR(SR)-SUB03-DS-IG-EN 3 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART SuBaRu WRX StI WIth aMPlIfIeR 2019-2021 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Reverse Light (+) E-Brake (-) VSS (vehicle speed sensor) (DATA) Power Antenna (+) Orange Purple/White Lt Green Pink Blue N/A Orange/White Yellow/Blue Green/White Blue Orange/White Purple/White Lt Green Pink Blue Orange/White Purple/White Lt Green Pink N/A Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 5 maestro.idatalink.com MODULE DIAGNOSTICS LED 1 PROGRAMMING BUTTON LED 2 SuBaRu WRX StI WIth aMPlIfIeR 2019-2021 LED 1 LED 1 Module/Firmware status · or · · · · · LED 2 (RR2) Bluetooth activity · · LED STATUS RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes OFF DIAGNOSTIC LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult troubleshooting table. After radio boots up : Normal operation. Bluetooth is activated. Turns off after one minute: Normal operation. Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 6 maestro.idatalink.com TROUBLESHOOTING TABLE SuBaRu WRX StI WIth aMPlIfIeR 2019-2021 PROBLEM Gauges do not work, radio shows OBD2 Error 1 or Error 2. The light on the Maestro is blinking RED TWICE. The light on the Maestro is flashing RED ONCE. The Harman Kardon system has no sound. (if applicable) SOLUTION Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. There is no firmware on the module; flash the RR module. Ensure the BLUE/WHITE amp turn-on wire is connected. Ensure the 6-pin connector (the plug with blue, green, green/black, purple, and purple/black wires) on the T-harness is not connected to the car. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 7 maestro.idatalink.com INSTALL GUIDE 2019-2021 SuBaRu WRX WIth aMPlIfIeR RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! PRODUCTS REQUIRED iDatalink Maestro RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU3 Installation Harness iDatalink compatible radio OPTIONAL ACCESSORIES ELECTRONICS Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB03-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. TABLE OF CONTENTS Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table SuBaRu WRX WIth aMPlIfIeR 2019-2021 3 4 5 6 7 NEED HELP? 1 866 427-2999 maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 2 maestro.idatalink.com INSTALLATION INSTRUCTIONS P1/1 STEP 1 · Unbox the aftermarket radio and locate its main harness. · Connect the wires from aftermarket radio main harness to the SU3 T-harness and match the wire functions. · Remove the factory radio. Note: only connect purple/white wire to radio reverse input or module damage will occur. STEP 2 · Assemble the SU3 T-harness and connect it to the factory radio harness. · Locate the 28 pin connector on the SU3 T-harness. Cut the Brown/Red wire (pin 9), extend and connect it to the Red wire (pin1) of the 40 pin climate control connector. Cut the Brown/Yellow wire (pin 10), extend and connect it to the Blue wire (pin2) of the 40 pin climate control connector. STEP 3 · Plug the OBDII connector into the OBDII of the vehicle, under driver dash. STEP 4 · Plug the aftermarket radio harnesses into the aftermarket radio. · Plug the RCA connectors to the aftermarket radio. · Plug the AUX cable to the aftermarket radio. · Plug the Backup camera cable to the aftermarket radio. · Plug the Data cable to the data port of the aftermarket radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. STEP 5 · Connect all the harnesses to the Maestro RR2 module then test your installation. Automotive Data Solutions Inc. © 2022 3 ADS-RR(SR)-SUB03-DS-IG-EN SuBaRu WRX WIth aMPlIfIeR 2019-2021 3 maestro.idatalink.com SuBaRu WRX WIth aMPlIfIeR 2019-2021 WIRING DIAGRAM STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK LF RCA INPUT RF RCA INPUT GREEN GREEN/BLACK PURPLE NC PURPLE/BLACK BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) PURPLE/WHITE - REVERSE LIGHT (+) * LTGREEN - E-BRAKE (-) PINK - VEHICLE SPEED BLUE - POWER ANTENNA SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS * ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR STEP 2 FACTORY RADIO HARNESS STEP 4 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CONNECT TO AFTERMARKET RADIO MAIN HARNESS AUX BACKUP CAM DATA CABLE WIRES FROM NC VEHICLE CUT AND ISOLATE BROWN/RED WIRE (PIN 9) BROWN/YELLOW WIRE (PIN 10) BROWN/RED BROWN/YELLOW STEP 3 CLIMATE CONTROL CONNECTOR RED 12 BLUE OBDII CONNECTOR STEP 5 MAESTRO RR2 MODULE SU3 T-HARNESS NOT REQUIRED Automotive Data Solutions Inc. © 2022 STEERING WHEEL CONTROL CABLE AUDIO CABLE ADS-RR(SR)-SUB03-DS-IG-EN 3 4 maestro.idatalink.com RADIO WIRE REFERENCE CHART SuBaRu WRX WIth aMPlIfIeR 2019-2021 Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Reverse Light (+) E-Brake (-) VSS (vehicle speed sensor) (DATA) Power Antenna (+) Orange Purple/White Lt Green Pink Blue N/A Orange/White Yellow/Blue Green/White Blue Orange/White Purple/White Lt Green Pink Blue Orange/White Purple/White Lt Green Pink N/A Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 5 maestro.idatalink.com MODULE DIAGNOSTICS LED 1 PROGRAMMING BUTTON LED 2 SuBaRu WRX WIth aMPlIfIeR 2019-2021 LED 1 LED 1 Module/Firmware status · or · · · · · LED 2 (RR2) Bluetooth activity · · LED STATUS RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes OFF DIAGNOSTIC LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult troubleshooting table. After radio boots up : Normal operation. Bluetooth is activated. Turns off after one minute: Normal operation. Normal operation (inactive). VIDEO HELP Installation, product information, vehicle specific videos. VERIFY FLASH Last flash information, steering control configuration, vehicle information. WEBLINK Software to program module. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 6 maestro.idatalink.com TROUBLESHOOTING TABLE SuBaRu WRX WIth aMPlIfIeR 2019-2021 PROBLEM Gauges do not work, radio shows OBD2 Error 1 or Error 2. The light on the Maestro is blinking RED TWICE. The light on the Maestro is flashing RED ONCE. The Harman Kardon system has no sound. (if applicable) SOLUTION Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. Make sure the correct radio model and serial number were entered during the flash. Verify the radio's serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number. There is no firmware on the module; flash the RR module. Ensure the BLUE/WHITE amp turn-on wire is connected. Ensure the 6-pin connector (the plug with blue, green, green/black, purple, and purple/black wires) on the T-harness is not connected to the car. MAESTRO RR RESET PROCEDURE: Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module's programming button and connect all the connectors back to the module. Wait, the module's LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful. TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/ IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer's website and look for any updates pertaining to your radio. Automotive Data Solutions Inc. © 2022 ADS-RR(SR)-SUB03-DS-IG-EN 7 maestro.idatalink.com