lexilights.io
User Manual for LEXI models including: 10011, 2ATOT10011, 10011 A19 Smart Color and Tunable White Bulb, 10011 A19, Smart Color and Tunable White Bulb
Lexi Devices, Inc. 10011 A19 Bulb - Smart Color and Tunable White with Bluetooth and Zigbee 2ATOT10011 2ATOT10011 10011
File Info : application/pdf, 1 Pages, 90.64KB
DocumentDocumentFCC ID:2ATOT10011 User Manual LEXI Light Bulbs Smart Color & Tunable White #10011 - A19 Bulb #10012 - BR30 Bulb WELCOME TO LEXI USER GUIDE - WORK WITHOUT LEXI HUB 1. Please select the ENVIRONMENT (NO HUB) mode at the menu of LEXI App by selecting "Add Environment/Hub" 2. Power on your light source(s), you'll see the light(s) flashing with warm white color 3. Select "ADD NEW DEVICE" at the LEXI App and follow the instruction to complete adding the device(s). As the device is being added, you will see the flashing rate increase briefly. Once added, your light will stop flashing. 4. Your devices is added to the LEXI system successfully and ready to use. 5. To learn more about detail function and special effect, Please go to www.lexilights.io USER GUIDE - WORK WITH LEXI HUB 1. If you are using a LEXI Hub, make sure its powered on and connected to the internet. Also, make sure your LEXI Hub is ready to add device(s) and work properly with the LEXI App at your smart devices. ( Detail instruction at the User Manual of LEXI Hub) 2. Power on your light source(s), you'll see the light(s) flashing with warm white color 3. Select "ADD NEW DEVICE" at the LEXI App and follow the instruction to complete adding the device(s). As the device is being added, you will see the flashing rate increase briefly. Once added, your light will stop flashing. 4. Your devices is added to the LEXI system successfully and ready to use. 5. To learn more about detail function and special effect, Please go to www.lexilights.io WARNINGS AND CAUTIONS: - BEFORE REPLACING, TURN OFF MAINS POWER AND LET LAMPS COOL TO AVOID ELECTRICAL SHOCK OR BURN. - NOT FOR USE IN ENCLOSED LUMINAIRES - This device is not intended for use with emergency exits. - The bulb is not suitable for use with traditional dimmers - Keep away from liquids and humidity. - The product is for indoor use only. Do not use in wet locations, directly exposed to water or outdoors. - This product is not a toy designed to be played with by children. - Do not place on hot surfaces. - For safety reasons and under the terms of the warranty, none of the enclosed devices should be opened. - Only use the adapter supplied: using a different adapter can damage the product. WARRANTY: LEXI provided one-year warranty is valid if the product is used in accordance with the instructions and for its intended purpose. Claims will only be accepted on submission of the original proof of purchase (invoice, sales slip or receipt) stating the purchase date, the name of the dealer and a description of the product with product ID labeled at the products. The LEXI's warranty lapses if: a. Anything has been changed, crossed out, deleted or rendered illegible on the purchase docket or product description. b. The failure is caused by damage, faulty connections or abuse. c. A defect is caused by extreme circumstances not inherent to the product, for example, lighting, flooding, fire, incorrect use or negligence. d. The product has been opened or disassembled. TROUBLESHOOTING - Ensure your device is within 60 feet without an obstacle between either your LEXI Hub or your mobile phone (when being used without a Hub) - Ensure your mobile phone has turned on both Bluetooth and location services. - Make sure the light is screwed in the socket completely. - Confirm device is paired with LEXI Hub or with your mobile phone - You can un-pair the lights by power cycling the light 6 times. This will return it to the unpaired mode (warm white, slow flashing) Then, re-pair this light as the user guide. WIRELESS SPECIFICATION: Frequency: 2400-2484MHz Wireless communication protocol: Bluetooth Low Energy and IEEE 802.15.1 Zigbee and IEEE: 802.15.4 Channel of BLE: 0-39 Channel of Zigbee: 11-26 ENVIRONMENTAL SPECIFICATION: Temperature (operation): -10...40°C Temperature (storage): -25...60°C Relative humidity: 5-95% non-condensing CLEANING AND MAINTENANCE: Do not clean when the product is on and connected to mains power. To avoid scratching, the product should only be cleaned with a soft dry cloth. Do not use cleaning agents. PLEASE KEEP THIS PACKAGING FOR FUTURE REFERENCE AS IT CONTAINS IMPORTANT INFORMATION. DISPOSAL OF YOUR OLD PRODUCT: FCC WARNING AND CAUTION: WARNING AND CAUTION: NOTE: This equipment generates, uses and Your product is designed and - This device complies with Part 15 of the 4Only use the control provided with or can radiate radio frequency energy and, manufactured with high quality materials FCC Rules. Operation is subject to the specified by these instructions to control if not installed and used in accordance and components, which can be recycled following two conditions: this lamp. This lamp will not operate with the instructions, may cause harmful and reused. When (1) this device may not cause harmful properly when connected to a standard interference to radio communications. this crossed-out wheeled bin symbol is interference, and (incandescent) dimmer or dimming However, there is no guarantee that attached to a product it means the (2) this device must accept any control. interference will not occur in a particular product is covered by the European interference received, including installation. If this equipment does cause Directive 2002/96/EC. interference that may cause undesired FCC ID : harmful interference to radio or television operation. 10011 - A19 Bulb ( FCCID: 2ATOT10011) reception, which can be determined by Please find out for yourself about the local - Changes or modifications to this unit not 10012 - BR30 Bulb ( FCCID: 2ATOT10012) turning the equipment off and on, the separate collection system for electrical expressly approved by the party - Shielded Cables must be used with this user is encouraged to try to correct the and electronic products. Please act responsible for compliance could void the unit to ensure compliance with the Class B interference by one or more of the according to your local rules and do not user's authority to operate the FCC limits following measures: dispose of your old products with your equipment. - Reorient or relocate the receiving normal household waste. The correct (3) Radiation Exposure Statement: This NOTE: This equipment has been tested antenna. disposal of your old product will help equipment complies with FCC radiation and found to comply with the limits for a - Increase the separation between the prevent potential negative exposure limits set forth for an Class B digital device, pursuant to Part 15 equipment and receiver. consequences for the environment and uncontrolled environment. This equipment of the FCC Rules. These limits are - Connect the equipment into an outlet human health. should be installed and operated with designed to provide reasonable on a circuit different from that to which minimum distance 20cm between the protection against harmful interference in the receiver is connected. THIS DEVICE IS NOT INTENDED FOR USE radiator & your body. a residential installation. - Consult the dealer or an experienced WITH EMERGENCY EXITS" radio/TV technician for help.