User Manual for MINSUO models including: AI6017PK2, 2AOV6-AI6017PK2, 2AOV6AI6017PK2, SP-002, SP-002 Dual DIY Wireless Wall Mounted Speakers, Dual DIY Wireless Wall Mounted Speakers, Wireless Wall Mounted Speakers, Wall Mounted Speakers, Speakers
Shenzhen Minsuo Industrial Co.,Ltd AI6017PK2 Dual DIY Wireless Wall Mounted Speakers 2AOV6-AI6017PK2 2AOV6AI6017PK2 ai6017pk2
Dual DIY Wireless Wall Mounted Speakers SP-002 SP-002 Included -Speaker x2 -USB-C charging cable x2 -Audio cable x2 -Screws and nuts x4 -3M adhesive tapex2 -User manualx1 Thank you for purchasing Our company's wireless speakers, please read this guide to ensure safe and satisfactory operation, please Keep this guide in a Safe Place for future reference. Instruction: 1 2 3 4 5M 6 USB Port 7 TF card port 8 Charging port 9 Aux-in 10 Power saving mode Press once to play / pause. Press and hold for 1-2 seconds to Power on/off. Press once to switch to previous song. Press and hold to turn down the volume. Press once to play / pause. Press once to pick up or ending the phone call. Press and hold for 1-2 seconds to reject phone call. Double click to call last number in your list. Press once to switch to next song. Press and hold to turn up the volume Press once to switch to FM radio/Bluetooth mode. Long press 2 seconds to TWS function(based on 2 pcs speaker) USB mode TF mode USB-C Aux-in mode The headphone turn off after 10 mins if not paired to a device. 1 6 2 3 7 4 8 M 9 5 Technical Specification: Bluetooth Version 5.3 Battery capacity 1200mAh Speaker power 5W Bluetooth frequency 2402-2480mHz Charge time 3-4 hours Play time 4-5 hours Function Handsfree, TF card, FM,AUX-IN, Bluetooth,support TWS To start the TWS pairing (1+1),please follow: 1.Turn on 2pcs bluetooth speakers. (Do not connect your smartphone's bluetooth or insert TF card) 2.Press and hold 'M' one of the speakers for around 2 seconds,it will be indicated with a "beep",then successfully finished TWS pairing. (If you don't want to TWS pairing, do the same instruction). 3.After finished TWS pairing, connecting your smartphone's bluetooth. Accessories list: 3 MElectronics 3 MElectronics Electronics 3 MElectronics Electronics Electronics 3EM lectronics 3EM lectronics 3 MElectronics Electronics 3EM lectronics 3 MElectronics 3 MElectronics 1 2 3 4 5 Installation Method 1: 3 MElectronics Electronics 3 MElectronics Electronics 3EM lectronics 3EM lectronics 3 MElectronics Electronics 3EM lectronics 3 MElectronics 3 MElectronics 3 MElectronics 3 MElectronics Electronics Electronics 3EM lectronics 3EM lectronics 3 MElectronics Electronics 3EM lectronics Electronics 3 MElectronics 3 MElectronics 3 MElectronics Step1: Peel off one side of the film on 2 . Step2: Put and stick 2 at the back of 3 . Installation Method 2: Before installation,please first drill 2 holes in a wall for further steps. cnot included Step1: put 5 into the holes. 3 MElectronics Electronics 3 MElectronics Electronics 3EM lectronics 3EM lectronics 3 MElectronics Electronics 3EM lectronics 3 MElectronics 3 MElectronics Step3: Peel off the other side of the film on 2 . Step4: Put and stick 3 onto the wall or any clean & flat surface. Step3: install 4 into the wall. Step2: put 4 through the hole of 3 Step5: Install 1 into 3 then done . Step4: install 1 to 3 then done. FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.Adobe Illustrator CC 23.1 (Windows) Adobe PDF library 15.00