User Manual for Shenzhen Nearbyexpress Technology Development models including: TT-CL00X, 2AVUHTT-CL00X, TT-CL025, Wireless LED Stand Light
Shenzhen NearbyExpress Technology Development Company Limited TT-CL00X Wireless LED Stand Light Remote control 2AVUHTT-CL00X 2AVUHTTCL00X tt cl00x
taotronics manual filetype:pdf - Google Search
TT-CL025 instructions 1. LED Stand Light Remote control appearance 2.Basic parameters of remote control Name LED Stand Light Remote control Model Device name Compatible system Weight Bluetooth communication Bluetooth frequency PCB material Battery TT-CL025 TAOTRONICS Selfie IOS/Android 50g 4.2 2.4G MHz FR4 CR2032 Bluetooth transmitting power Bluetooth remote control distance operating electricty <0DB/M >6m Due to different phone models, the antenna design of the phone is different, and the distance will be different if the environment is different. The actual distance should be subject to the actual measurement of the phone <16MA DC=3.3V Standby electricty <8UA DC=3.3V 3.Bluetooth setting 1,Hold 3s to turn on bluetooth,the indicator light 250ms flashes rapidly and enters the pairing mode. After holding 3s, it enters standby mode. It will automatically turns off after 7 minutes in standby mode.The blue light will turn off after lighting 1s. If there is a trigger button in standby mode, then go back to the pairing mode and will restart the counting time again. 2,If the phone has been paired before, it will be preferred to connect the phone that has been paired before(the phone that has been paired last time) 3,After successful pairing, the blue light shines for 2s then light off 4,Hold 3s to turn off, the blue light shines for 1s then light off 5,Press and hold the button to keep the light on. Release the light and it will go out instantly. 6,If bluetooth is turned off after pairing successfully with the mobile phone, the indicator light 250ms flashes rapidly and enters the pairing mode. After 3s, it enters standby mode. after 7min, it will be shut off automatically, and the blue light shines for 1s then light off.If the phone turns on Bluetooth again under the pairing mode, it will automatically connect back, and the bluetooth shines 2S will be light off! If phone's bluetooth is turn on under the standby mode, the button needs to be triggered to wake up the remote control bluetooth and automatically connect back after awakening. Note: Blue light does not turn on when the Bluetooth is off. Anytime the pairing is successfully paired, the bluetooth light shines 2s then light off. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) L' appareil ne doit pas produire de brouillage; (2) L' appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d' en compromettre le fonctionnement. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Microsoft Word 2010 Microsoft Word 2010