User Guide for VANCH models including: VI-IR610P, 2A3H9VI-IR610P, 2A3H9VIIR610P, VI-IR610P, VI-IR610P RFID UHF Fixed Industrial Reader, RFID UHF Fixed Industrial Reader, UHF Fixed Industrial Reader, Fixed Industrial Reader, Industrial Reader
Shenzhen Vanch Intelligent Technology Co.,Ltd VI-IR610P UHF RFID Industrial Reader 2A3H9VI-IR610P 2A3H9VIIR610P vi ir610p
File Info : application/pdf, 17 Pages, 635.18KB
DocumentDocumentRFID UHF fixed Industrial Reader VI-IR610P
Product Information Guide
Page 1 of 15
Con t e n t s
1 Product Overview ...........................................................................4 1.1 Shape and interface ....................................................................... 4 1.2 Performance ..................................................................................6 1.3 Function ........................................................................................ 7
2 Product installation ......................................................................... 8 2.1 Connection relationship ................................................................. 8 2.2 Installation steps........................................................................... 8 2.3 Install the reader .......................................................................... 9 2.4 Install the antenna ........................................................................ 9 2.5 Connect the antenna and reader ................................................... 10 2.6 Connect the reader and the host computer .................................... 10 2.7 Connect power supply .................................................................. 12 2.8 Equipment joint debugging ........................................................... 12 2.9 Label ........................................................................................... 13
3 Common malfunctions .................................................................... 14
Page 2 of 15
1 Product Overview
The VI-IR610P reader is t he lat est generat ion product developed by our com pany. The reader can read and writ e "elect ronic t ags" ( or "cards"- t he m eaning of t he t wo in t his m anual is equivalent ) t hat m eet s t he EPC CLASS1 G2 st andard. The reader can be used in dat a acquisit ion syst em s such as card issuance and personnel access control m anagem ent.
1.1 Shape and int erface
The VI-IR610Preader/ writ er adopt s an alum inum alloy shell and can be installed in an indoor cabinet or an outdoor protective box with good ventilation, dust and rain conditions.
The VI-IR610P reader is divided int o ant enna int erface end face, com m unicat ion int erface end face and LED indicat or face from t he appearance:
1 VI-IR610P ant enna port ( P 1- 1- 1) : ANT1 ANT2ANT3 and ANT4
P 1-1-1
Page 3 of 15
2 Com m unicat ion int erface face ( P 1- 1- 2) :
P 1-1-2
P 1- 1- 2 communication interface has the following characteristics:
A. power port : DC12V female B. RJ45 communication interface: St andard version: Connect t he cable
to the network directly C. POE power supply (The switch must support 1, 2, 3, and 6 pins for power
supply). Opt ional version: opt ional super net work port , no POE power supply D. RS232 E. GP I O
GPI O ( Double 10 st it ches) Front view reader int erface panel
GPIO interface terminal definition (from left to right)
26 34
RS485- NC
DO1- DO2- DO3- DO4- DI2 WD1_1 WD2_1
GND
26 34
RS485+ NC
DO1+ DO2+ DO3+ DO4+ DI1 WD1_0 WD2_0
GND
Page 4 of 15
Special at t ent ion: "GND" in GPI O becom es RJ45 net work port on t he right
3LED light ( P 1- 1- 3)
P 1- 1- 3 LED light LED I nst ruct ion m eaning: Red light - power indicat or, red light on m eans t he power is on. Green light - RF light , flashing green light indicat es t hat t he reader is receiving/ sending data and com m ands. Yellow light - running indicat or, flashing yellow light indicat es t hat t he device is operating norm ally.
1.2 Perform ance
( 1) Working frequency: 865~ 868MHz ( EU) 902928MHz ( US) 920~ 925MHzCN
N ote: Please adjust the w orking frequency according to the
Page 5 of 15
country or region before use, so as not to interfere w ith other radio com m unication equipm ent. (2) Working m ode: continuous (autom atic), com m and, trigger. (3) Working m ode: continuous (autom atic), com m and, trigger. ( 4) RF power: 033dBm adj ust able ( 5) Com m unicat ion rat e: The serial port rat e is 9600115200bps, RJ45 is 10Mbps ( 6) Reading dist ance: 0- 25000m m ( relat ed t o reader param et er configuration, antenna gain, tag type), writing distance: 0-1000m m (related to reader param eter configuration, antenna gain, tag type) ( 7) Power supply: Met hod 1: DC12V/ 3A, Support D C9 V~ 2 4 V w ide volt age DC9 V~ 2 4 V Met hod 2POE power supply ( only support s 100M 1236 line sequence power supply)
Page 6 of 15
(8) Support 4G ( opt ional) (9) Support WI FI ( opt ional) (10) m inus 5° aut om at ic heat ing device ( opt ional) ( cust om ers can determ ine according to proj ect needs) (11) Power consum pt ion: Maxim um power consum pt ion 15W (12) Whole m achine w eight : about 1.32kg ( com plet e set ) (13) Working t em perat ure: - 2040. (14) Buzzer: Built - in buzzer, every t im e t he reader reads t he electronic tag, it will sound.
Funct ion
(1) Read and write tags: electronic tags that comply with EPC ISO18000-6C and ISO18000-6B (2) It can read multiple EPC code labels of different lengths (16, 32, 48, 64, 80 or 96 bits) at the same time (3) Read the EPC data of the selected tag (4) Read the user area data of the selected label (5) Read the data in the TID area of the selected tag (6) Readable tag access and destruction passwords (both are 32 bits) (7) EPC codes of different lengths (16, 32, 48, 64, 80 and 96 bits) can be written (8) User area data can be written (9) The password for tag access and destruction can be modified (both are 32 bits)
Page 7 of 15
Aft er sales service | VF- 747P product guide
2 Product installation
2.1 connect ed relation
I n the applicat ion system , the connect ion relat ionship bet ween t he reader, m icrowave ant enna, elect ronic t ag, and cont roller ( or PC) is shown in t he following figure:
P 2-1-1
2.2 I nst allat ion Pr ocedur e
When installing t he equipm ent , follow t he following st eps: Put the reader Install antenna
Connect the reader and t
Connect reader and controller EquPiopwmeernot njoint db i Put labels
Page 8 of 15
Aft er sales service | VF- 747P product guide
2.3 I nstall reader
The inst allat ion of t he reader should pay at t ent ion t o t he following m at t ers: (1) The VF- 7 47P reader has no special wat erproof and dust proof t reat m ent , and it s working t em perat ure range is: - 20~ + 40; t herefore, it is m ore suitable for working in an indoor environm ent. I f you want to install it outdoors, you m ust put the reader and power converter in the prot ect ive box. The prot ect ive box is required t o have t he funct ions of rainproof, dustproof, heat preservation and heat insulation to provide a better working environm ent for the reader. (2) The RF line dist ance bet ween t he posit ion where t he reader is placed and the antenna should not exceed 10 m eters (3 m eters is better). (3) The m axim um dist ance of reliable com m unicat ion bet ween t he reader and the controller varies with t he dat a int erface When using t he RJ45 int erface t o com m unicat e: Support 10M/ 100M t ransm ission rat e, using a network cable, it is recom m ended that the t ransm ission distance should not be great er than 50 m et ers. When using RS485 int erface com m unicat ion: t he t wo wires RS485+ ( brown) and RS485- ( blue) on t he reader should be connect ed t o t he corresponding t wo pins of the controller. I t is recom m ended that the t ransm ission dist ance should not be greater than 80 m eters. For RS232 int erface: You can use t he support ing cable t o direct ly connect t o t he PC. I t is recom m ended t hat t he t ransm ission dist ance should not be great er t han 10 m et ers. The connect ion diagram is shown in t he figure below:
Page 9 of 15
Aft er sales service | VF- 747P product guide
P 2-2-1
Page 10 of 15
Aft er sales service | VF- 747P product guide
2.4 I nstall ant enna
The antenna installation needs to consider factors such as position, height and angle to meet the following application requirements: (1) Ensure that the antenna beam range can cover the range of reliable reading of electronic tags. (2) Ensure that the length of the RF cable from the antenna to the reader is not more than 10 meters, preferably not more than 3 meters. (3) Depending on the specific application, the antenna can be installed horizontally top-mounted (gantry) or vertical side-mounted (post), but the polarization direction of the antenna must be consistent with the polarization direction of the electronic tag.
2.5 Connect t he ant enna and reader
The VF-747P reader provides 4 SMA male RF interfaces, which require low-loss coaxial cables to be connected to the antenna. Since the longer the cable length, the greater the attenuation of the high-frequency signal, the shorter the cable length is required for the application, the better. Increasing the length of the cable or using an ordinary cable will affect the reading and writing distance of the reader. When the connection distance between the antenna and the reader is within 3 meters, it is recommended to use the1/2 feeder; when the distance is more than 3 meters, the 7/8 feeder. The cable length must not exceed 10 meters. The cable connector is connected with the antenna and the reader terminal Should be tightened. After the cable connector is tightened, the cable connector should be sealed by heating and shrinking or tightening with tape to protect the cable connector. WIFI/4G connection port and antenna (this port is optional)
N ote: I t is not recom m ended to use ordinary cables to connect the antenna; it is not recom m ended to assem ble the cable connector by y ou r se lf .
2.6 Connect t he r eader and t he host com put er
The VI-IR610P reader can be connect ed t o t he host com put er ( or PC) t hrough eit her of t he RS232 or RJ45 port s t o receive com m ands and send dat a.
Page 11 of 15
Aft er sales service | VF- 747P product guide
P 2-6-1 The reader is direct ly connect ed t o t he PC, as shown in t he figure below, t he wiring arrangem ent is as follows:
P 2-6-2 Pin 1 of t he RJ45 port of t he reader is connect ed t o pin 3 of t he RJ45 port of t he PC, pin 3 of t he RJ45 port of t he reader is connect ed t o pin 1 of t he RJ45 port of t he PC, pin 2 of t he RJ45 port of t he reader is connect ed t o pin 6 of t he RJ45 port of t he PC , Pin 6 of t he RJ45 port of t he reader is connect ed t o pin 2 of t he RJ45 port of t he PC, and t he ot her pins are connect ed correspondingly. The reader and t he PC are connect ed t hrough t he Hub, using a straight - through connect ion line. 2 Connect ion t hrough RS232 port The RS232 port can be direct ly connect ed t o t he PC wit h t he support ing cable. The lengt h of t he RS232 port connect ion line in t he proj ect should be less than 10 m eters.
Page 12 of 15
Aft er sales service | VF- 747P product guide
2.7 Connect ing power Supplies
The VF- 747P reader/ writ er adopt s + 12/ 3A DC power supply. Along wit h t he reader, our com pany provides an AC/ DC convert er t hat m eet s t his requirem ent . The power connect ion m et hod is as follows:
( 1) Check and confirm whet her t he volt age and working frequency of t he AC power supply m eet t he requirem ent s of: AC100240V/ 50Hz; ( 2) I nsert t he DC out put plug of t he power convert er int o t he + 12V DC input port of t he reader ( 3) I nsert or connect t he 220V AC power input line of t he convert er t o t he AC power supply line. ( 4) The red indicat or light of t he power supply of t he reader should be on, indicat ing t hat t he power input is normal.
2.8 The equipm ent alignm ent
The key of device alignm ent is t o adj ust t he height , direct ion Angle and inclinat ion of the ant enna so that t he reader can read t he electronic t ags wit hin t he desired range. The debugging m et hod is:
( 1) Turn on t he power of t he reader, set t he reader t o t he t im ing working m ode, close t he param et er set t ing program and disconnect t he connect ion wit h t he PC. ( 2) Turn off t he power of t he reader and t hen t urn it on again, t he reader will aut om at ically ent er t he tim ing working state. ( 3) Because t he m at erial of t he ident ified obj ect is different , t he required label is also different . Therefore, when debugging, the elect ronic label should be affixed t o t he obj ect wit h t he sam e m at erial as t he surface of t he ident ified obj ect , and back and fort h wit hin t he range where the label is expect ed to be read. Move obj ect s. I f t he reader can read t he elect ronic label correct ly, t he built - in buzzer will sound and t he RF The LED flashes. ( 4) Carefully adj ust t he height and angle of t he ant enna t o m ake t he reading range t he best . N ote: The reader only radiat es m icrow ave pow er w hen reading and w rit ing t ags. At this t im e, t he inst allat ion and debugging personnel should be at least 7 0 cm aw ay from t he ant enna t o m e e t t he r e qu ire m e n t s of t h e US FCC for t h e hu m a n body . Exposure t o t he m axim um allow able radio frequency ( RF) radiat ion requirem ents.
Page 13 of 15
Aft er sales service | VF- 747P product guide
2.9 Attach label
I n t he application process of radio frequency ident ification syst em , labeling is oft en done. The issues t hat need t o be paid at t ent ion t o when labeling are:
( 1) Use t he adhesive glue recom m ended by t he m anufact urer. ( 2) For labels applied t o m et al surfaces, special adhesive glue should be used. ( 3) The posit ion of t he label on t he surface of t he obj ect m ust also undergo field t est s t o ensure t he best read and writ e effect .
3 Com m on Fa ult s
Table 4- 1 Com m on fault s of readers and solut ions
Failure phenomenon Can't read card
Unable to connect to the reader module
Card reading distance is very close
Possible reason Beyond the reading area of the reading and writing module
The antenna is damaged
The parameter RF Power value is too low Bad label Module is broken POE for power supply
Com is occupied or broken
The data line is broken or not connected
Com port occupied port out of range
Module is broken
Antenna not connected
The parameter RF Power value is too low The label and the antenna polarization direction are inconsistent Module is broken Bad label
Solution Move the card closer to the antenna of the reader module Replace the reader antenna
Restore factory parameters
Change to other label test Contact technical support Contact technical support Check the port occupancy through the device manager and test whether the port can communicate Replace the data cable or check the connection of the data cable Check the com port through the device manager, and change the com port to a value within 10 Contact technical support Check the antenna connection
Restore factory parameters
Rotate the label 90 degrees
Contact technical support Change other labels
CAUTION
Page 14 of 15
Aft er sales service | VF- 747P product guide
1.Use careful with the earphone maybe possible excessive sound pressure from earphones and headphones can cause hearing loss
2. CAUTION : RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS 3. The product shall only be connected to a USB interface of version USB2.0 4. Adapter shall be installed near the equipment and shall be easily accessible 5. Operation temperature:-20~40ºC 6. The plug considered as disconnect device of adapter 7. The device complies with RF specifications when the device used at 50cm from your body 8. AC adapter: Model No.: TDX-1203000 Input: 100-240V~, 50/60Hz,2.0A Output: 12.0Vac3.0A Shenzhen VANCH Intelligent Technology Co.,Ltd , hereby declares that this UHF RFID Industrial Reader is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. This information has to be presented in such a way that the user can readily understand it. Typically, this will necessitate translation into every local language (required by national consumer laws) of the markets where the equipment is intended to be sold. Illustrations, pictograms and using international abbreviations for country names may help reduce the need for translation. Max power: RFID: 25.353 865MHz-868MHz
Page 15 of 15
FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
The distance between user and product include antenna should be no less than 20cm during normal operations.
IC STATEMENT This device complies with Industry Canada licence-exempt RSS standard(s) Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with RF exposurerequirements, a minimum separation distance of 20mm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Ce dispositif est conforme aux normes autoriser-exemptes du Canada RSS d'industrie L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.Cet équipement est conforme avec l'exposition aux radiations IC définies pour un environnement non contrôlé. L'utilisateur final doit respecter les instructions de fonctionnement spécifiques pour satisfaire la conformité aux expositions RF. Cet émetteur ne doit pas être co-localisées ou opérant en conjonction avec une autre antenne ou transmetteur. Pour se conformer aux exigences d'exposition aux radiofréquences, une distance minimale de 20 mm doit être maintenue entre le corps de l'utilisateur et le combiné, y compris l'antenne. Les pinces de ceinture, les étuis et autres accessoires similaires utilisés par cet appareil ne doivent pas contenir de composants métalliques. Les accessoires portatifs qui ne répondent pas à ces exigences peuvent ne pas se conformer aux exigences d'exposition RF et doit être évitée. Utilisez uniquement l'antenne fournie ou une antenne approuvée
Adobe PDF Library 15.0