Subordinate New Brand AC SCR-Dimmer (Zigbee 3.0 + 2.4G + Push)

Features

• No signal cable required, easy and cost-effective installation, preserving original wiring.
• Mini appearance fits EU/USA standard junction boxes.
• Wide application for single-color Triac LED lights, incandescent lamps, and halogen lamps.
• Zigbee 3.0 Standard Protocol ?
• Smartphone APP Control ? (requires Zigbee 3.0 Gateway purchase)
• 2.4G RF Remote Control ?
• Push Dimming Function ?️
• Phase-Cut Technology with Trailing Edge
• 0~100% Stepless Dimming and Flicker-Free
• Lowest Brightness Setting Function
• Built-in Temperature Sensing Switch, Overheat/Overload Protection ⚠️
• Automatic Transmission Function, Unlimited Control Range ?
• Reliable and easy-to-install Screw Connector
• Flame-Retardant PC Shell for Increased Safety ?

Various Control Solutions: Powered by Philips Hue, MiBoxer, IKEA TRÅDFRI Zigbee Gateway, 2.4GHz Remote, Amazon Echo Plus.

Parameters

Dimensions: 49mm x 25mm x 49mm. Includes Indicator Light ?.

Wiring Diagram

Connections:

• PUSH Switch (S1, S2)
• Input: AC100~240V (N, L)
• Output: (N, L1)
• Connects to: LED light with Triac dimming, Incandescent and Halogen lamps.

Attention ⚠️: Please check and ensure all wires are correctly connected before powering on, otherwise the dimmer can be easily damaged.

Breaker Mode: The dimming function is useless and the dimmer only supports ON/OFF once this mode is activated.

• Turn ON: Short press 'SET' ⚙️ 5 times quickly. The mode is activated once the indicator flashes 3 times rapidly.
• Turn OFF: Short press 'SET' ⚙️ 5 times quickly. The mode is shut down once the indicator flashes 3 times slowly.
• APP ON/OFF: See page 13.

Installation Diagram

Supports standard junction boxes. The depth of the junction box must be over 50 mm.

PUSH Dimming

• Short press PUSH switch: Turn light on/off ▶️/⏹️.
• Long press PUSH switch: Dim brightness steplessly. Keep your finger pressed and release it. Then repeat long pressing to increase or decrease brightness.
• To synchronize brightness for multiple dimmers connected to the same reset switch: Please press the switch for 20 seconds until all lights reach the same brightness at 100%.
• The number of dimmers connected to the same reset switch shall not exceed 25 pieces. The connection cable of the reset switch shall not be longer than 20 m.

Remote Control Instructions

Link Remote

For K1 Remote:

1. Learning Code Way 1: Short press 'SET' ⚙️ once, the indicator flashes.
2. Way 2: Turn off dimmer for 10 seconds and turn it back on.
3. Way 3: Short press the push switch to keep the light on.
4. Press 'SET' ⚙️ 3 times within 3 seconds. The pairing code is ready once the light flashes 3 times slowly.

For Other Remote:

1. Press any 'ON' button in group zones 3 times within 3 seconds. The pairing code is ready once the light flashes 3 times slowly.

Turn the light ON.

Unlink Remote

For K1 Remote:

1. Press 'SET' ⚙️ 5 times within 3 seconds. The unlink is successful once the light flashes 10 times rapidly.

For Other Remote:

1. Press any 'ON' button in group zones 5 times within 3 seconds. The unlink is successful once the light flashes 10 times rapidly.

Pairing / Unpairing Zone.

Compatible Remotes (sold separately)

B1 / B1-B / T1, K1 / K1-B, FUT087 / FUT087-B, S1-B / S1-W / S1-G, WL-Box1.

Set Minimum Brightness with Remote

This item should be paired with the remote first before setting.

For K1 Remote:

1. Long press 'SET' ⚙️ for 3 seconds until the light flashes once and the indicator enters flashing status.
2. Short press 'SET' ⚙️ to cycle through 10 brightness levels: 3%, 5%, 7%, 9%, 12%, 17%, 22%, 28%, 34%, 40%.
3. Short press the knob to confirm the setting, or wait 10 seconds for automatic confirmation. The light will return to the previous brightness level.

For Other Remote:

1. Long press the 'ON' button on the remote or the 'ON' button on the zone until the light flashes once and the indicator enters flashing status.
2. Short press the 'ON' button on the remote or the 'ON' button on the zone to cycle through 10 different brightness levels (3%, 5%, 7%, 9%, 12%, 17%, 22%, 28%, 34%, 40%).
3. Short press any button except 'OFF' to confirm the setting, or wait 10 seconds for automatic confirmation. The light will return to the previous brightness level.

Attention ⚠️: The Master OFF button can set the minimum brightness for all connected dimmers.

Automatic Transmission

One light can transmit signals from the remote to another light within 30m. As long as there is a light within 30m, the remote control range can be unlimited.

Signal Transmission: Triac Dimmer ? Distance 30m Triac Dimmer.

Attention ⚠️: All dimmers must be paired with the same remote control.

Smartphone APP Control Instructions

Added to Zigbee 3.0 'TUYA Smart' App ? (please read the Zigbee 3.0 Gateway manual).

Pairing Network

1. Connect to power supply ?.
2. Pairing Network (Attention ⚠️: Factory default is pairing network).
• Way 1: Press 'SET' ⚙️ for about 3 seconds until the indicator flashes rapidly.
• Way 2: Please turn on and off about 3 times (Attention ⚠️: Do not use a push switch for turning on and off).
• Way 3: Press the push switch for 10 seconds while the light is off (Attention ⚠️: must be wired to the push switch).
3. Open the 'TUYA Smart' APP ?, click on the Zigbee gateway, and then click 'Add sub device' ➕.
4. Click 'Indicator is flashing quickly' ✨.
5. Supports APP dimming or group control etc. once successfully added.

App Set Lowest Brightness

The light is off once the brightness is dimmed to 1%, please increase the lowest brightness.

Setting Method:

1. Click 'Settings' ⚙️ in the APP.
2. Slide the slider to finish the setting.

Breaker Mode (ON/OFF)

Attention ⚠️: The dimming function is useless and the dimmer only supports ON/OFF once this mode is activated.

Setting Method:

1. Click 'Settings' ⚙️ in the APP.
2. Click the icon on the right side of 'Breaker Mode'.

Philips Hue Control Instructions

Added 'Philips Hue' to the APP ?.

Pairing Network

1. Connect to power supply ?.
2. Pairing Network (Attention ⚠️: Factory default is pairing network).
• Way 1: Press 'SET' ⚙️ for about 3 seconds until the indicator flashes rapidly.
• Way 2: Please turn on and off about 3 times (Attention ⚠️: Do not use a push switch for turning on and off).
• Way 3: Press the push switch for 10 seconds while the light is off (Attention ⚠️: must be wired to the push switch).
3. Open the 'Philips Hue' App, click 'SETTINGS' ⚙️ and then click 'Lights' ?.
4. Click '+' ➕ in the upper right corner.
5. Click 'Search' ?.
6. Click 'Start configuration' and complete it.

Alexa Voice Control Instructions

Alexa Control (Audio supports Zigbee 3.0 protocol) ?️

You can connect directly if your Amazon ECHO already has an integrated Zigbee 3.0 protocol. Models with Zigbee 3.0 protocol include: Amazon ECHO Plus (2nd Gen), ECHO (4th Gen), ECHO Studio, ECHO Show (2nd Gen).

Pairing Network

1. Connect to power supply ?.
2. Pairing Network (Attention ⚠️: Factory default is pairing network).
• Way 1: Press 'SET' ⚙️ for about 3 seconds until the indicator flashes rapidly.
• Way 2: Please turn on and off about 3 times (Attention ⚠️: Do not use a push switch for turning on and off).
• Way 3: Press the push switch for 10 seconds while the light is off (Attention ⚠️: must be wired to the push switch).

Say to Amazon ECHO: "Alexa, Discover devices" ?️.

Wait a moment for the device to be discovered. Voice control is activated.

Alexa Control (Audio does not support Zigbee 3.0 protocol) ?️

Please add a device to the MiBoxer Zigbee 3.0 Gateway (see details on page 10), then proceed with the following steps.

1. Open the Alexa App.
2. Click 'More' in the bottom right corner.
3. Click 'Skills & Games'.
4. Click 'Search' ? in the upper right corner.
5. Enter 'Smart life' and search.
6. Click the 'Smart Life' skill, follow the instructions to complete the configuration and start voice control.

Google Home Voice Control Instructions ?

Please add the device to the MiBoxer Zigbee 3.0 Gateway (see details on page 10) and proceed with the following steps.

1. Open the Google Home App.
2. Click '+' ➕ in the upper left corner.
3. Click 'Set up device'.
4. Click 'Works with Google'.
5. Click 'Search' ? in the upper right corner.
6. Enter 'Smart life' and search.
7. Click the 'Smart Life' skill, follow the instructions to complete the configuration and start voice control.

Attention ⚠️

• Please turn off the power supply before installation.
• Please ensure the input voltage meets the device's requirements.
• Do not disassemble the device if you are not an expert, as it will be damaged.
• Please do not use the light in a location with extensive metal areas or strong electromagnetic waves nearby, as this will seriously affect the remote control range.

Dimmer cannot be used in humid environments.

Made in China.