Introduction
Thank you for purchasing this Mestic MW-120 Semi-Automatic Washing Machine. This product features a special cabinet integration technology, a plastic casing that prevents rust, and is relatively lighter and more space-saving than other twin-tub washing machines. Its new technology with a large wave pulsator and water flow ensures less twisting of clothes, better cleaning, and improved washing effect. Functions include water inlet, sprinkling, spin-dry, and water flow, saving time, labor, and water.
The machine is designed for ease of use and durability, offering efficient washing and spinning capabilities.
Specifications
| Feature | Details |
|---|---|
| Water Capacity | High: 36 L, Low: 32 L |
| Input Power | Wash: 250 W, Dry: 120 W |
| Power Source | Voltage: 220 V, Hertz: 50 Hz |
| Dimensions (LxWxH) | 57 x 36.5 x 62 cm |
| Weight | 10.1 kg |
Product Components
The washing machine consists of the following parts:
- 1. Spin cap
- 2. Spin tub
- 3. Spin cover
- 4. Water inlet
- 5. Control panel
- 6. Pulsator
- 7. Wash cover
- 8. Cabinet
- 9. Bottom
- 10. Wash timer switch
- 11. Wash & drain selector switch
- 12. Spin timer switch
- 13. Drain hose
- 14. Power wire
- 15. Back cover
Diagrams illustrating these parts are present in the original document.
Washing Instructions
Preparation
- Place the machine on a flat, level surface.
- Ensure the power outlet has a safety ground connection.
- Lay down the overflow hose.
- Use the water inlet hose to connect the water tap to the water inlet.
- Adjust the water level based on the type of clothing material and its weight.
- Turn on the power.
Washing
- Set the "wash & drain selector switch" according to the material type and weight of clothes.
- Set the "wash & drain selector switch" to the wash position.
- Set the "wash timer", place clothes into the tub, adjust the water level to the proper position, and add the correct amount of detergent.
- Set the "wash timer" to start the washing cycle.
- After washing, set the "wash & drain selector switch" to the drain position to empty the water.
Spinning
- After washing, connect the water inlet hose to the spin tub water inlet for 20-30 seconds.
- Spin the clothes for 1-5 minutes according to the "spin timer" process, repeating once or twice.
Rinsing
- After spinning, the spin tub will stop. Open the spin cover and transfer clothes from the spin tub to the wash tub to prepare for rinsing.
- Repeat the washing process but do not add any detergent.
Troubleshooting
| Problem | Reason | Solution |
|---|---|---|
| The pulsator is too slow | Power cut or switch off | Switch on the power |
| Transmission belt left off | Assemble the transmission belt | |
| Belt pulley has become loose | Tighten the belt | |
| Pulsator is blocked | Remove the block | |
| The pulsator does not rotate | Belt is loose | Tighten the belt or renew it |
| Abnormal noise and vibration | The clothes in the spin dry tub loosened | Tighten the belt and the screw |
| The clothes in the spin dry tub is unbalanced | Replace the clothes in the tub | |
| There is something jammed between the pulsator and the wash tub | Remove the jammed object(s) | |
| Water leaks from the wash tub | Wash tub was not connected tightly to the hose | Reconnect and tighten the hose |
| Spin-dry basket does not rotate | The slight switch is in loose contact | Adjust the contactor of the switch |
| The fixed screw of spin dry basket or shaft coupling is loose | Tighten the screw | |
| The fixed screw of spin dry basket or shaft coupling is loose | Remove the textile | |
| The spin tub does not drain | Brake dragline is loose | Tighten the dragline |
| Something had cropped into the space between spin tub and spin dry basket | Remove the object |
Points of Attention
- If a problem cannot be resolved, please contact the Service Center.
- For your own safety, ensure that the ground connection is correct.
- Never put your hands into the spin tub while it is working.
- Never wash textiles containing volatile materials to avoid machine damage or water blockage due to stains.
- The timer should always be turned clockwise.
- If abnormal sounds/movements occur during operation, stop the machine and check (refer to troubleshooting).
- When washing, the water temperature should be below 60°C to prevent plastic components from deforming.
Maintenance
After use, pull out the plug to prevent accidents.
Recycling Information
This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE Directive 2012/19/EU). It must be handled according to this directive for recycling or dismantling to minimize environmental impact. Contact local authorities for more information. Electronic products not sorted are potentially dangerous due to hazardous substances.
The original document includes symbols for WEEE, PAP (Paper/Cardboard), and HDPE (Plastic).
Declaration of Conformity
Gimeg Nederland B.V. declares that the device MW-120 complies with the basic requirements and other relevant regulations listed in the European directives for electromagnetic compatibility (2014/30/EU) and low voltage (2014/35/EU). A full declaration can be requested from the address on the back of this manual.
quefairedemesdechets.fr
