Unitech Global | Your Brilliant AIDC Solution Provider
User Guide for unitech models including: HT330 Series Rugged Handheld Terminal, HT330 Series, Rugged Handheld Terminal, Handheld Terminal, Rugged Terminal, Terminal
Купить тсд терминал сбора данных unitech ht330 в Тюмени | Цена
Купить тсд терминал сбора данных unitech ht330 в Магнитогорске | Цена
HT330 Series Rugged Handheld Terminal Quick Start Guide 609356G V1.3 Package Product View Keypad View Please make sure the following contents are in the
File Info : application/pdf, 2 Pages, 818.46KB
DocumentDocumentHT330 Series Rugged Handheld Terminal Quick Start Guide 609356G V1.3 Package Please make sure the following contents are in the HT330 gift box. If something is missing or damaged, please contact your Unitech representative. The Package Contents · HT330 Terminal · Battery · Hand Strap · USB Type-C Cable · Quick Start Guide Optional Accessories · Boot Case · Gun Grip · Terminal Power Adaptor · HT330 1-Slot Charging Cradle with spare Battery Slot · HT330 1-Slot USB Cradle with spare Battery Slot · Power Cord for Cradle · Glass Screen Protector · Stylus with coil strap Product View 1 10 13 2 3 11 14 12 15 4 16 5 6 7 8 9 1. Scanner Window 2. LED Indicator 3. 5MP Front Camera 4. 4"LCD Display 5. Volume Key 6. Scanner Trigger Key 7. Power Key 8. Function Key 9. Mic 17 18 10. 13MP Rear Camera 11. Mic 12. Battery Lock 13. Speaker 14. POGO Pin for Gun Grip 15. Holes for Hand Strap 16. Battery Cover 17. POGO Pin 18. USB Type-C Port Keypad View WARNING! There is a risk of fire and burns if the battery is handled improperly. DO NOT disassemble, crush, puncture, short external contacts, or dispose the battery pack in fire or water. DO NOT attempt to open or service the battery. Dispose of used batteries according to local recycling guidelines in your area. CAUTION! To ensure the unit working properly, please keep all connectors away from the contaminants staying inside of them such as dust, grease, mud, and water. The negligence may cause the unit with no communication, short circuited, overheated and so on. If the connector is damaged, please ensure the connector is being fully repaired before using the unit to avoid causing short circuited. http://www.ute.com/ Copyright 2022 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd. Inserting Micro SD/Nano SIM Card (Phone Ver. Only) Inserting the Nano SIM Card Push up the SIM card holder to unlock and flip the card holder to insert SIM card. Close the card holder and slide down to lock. Ensure that it is installed properly. Remove Battery Cover to Install Battery Remove the battery cover in the direction as shown in the picture below: 1. Push the battery lock to the right to unlock. Lock Unlock Flip open Inserting the Micro SD Card Push the SD card holder to the right to unlock and flip the card holder to insert the SIM card. Close the card holder and push to the left to lock. Ensure that it is installed properly. Unlock Lock Flip open Install the Battery Cover Insert the battery cover in the direction as shown in the picture below: 1. There are three hooks on the bottom of battery cover, align the hooks with the recesses on the battery compartment. 2. Grab the battery cover from the two recesses on the side, and lift to remove the battery cover. 3. Align the battery with the battery compartment, then push forward until you hear a click sound. 4. Press down the battery to secure in place. Checking LED Status 2. Insert the battery cover up to 45 degrees (45°) angle, from bottom to top. 3. Press down the battery cover to secure in place. Make sure there is no gap between the device and the battery cover. 4. Push the battery lock to the left to lock. Make sure the battery cover is securely closed, or you may not be able to turn on the terminal. LED Red Light Green Light Description Battery Charging Twinkling to indicate battery low status(less than 15%) Battery Fully charged Barcode scan good read Blue Light Message If scanner app is running, LED is controlled by scanner app. No LED (Red and Green) display when battery is out. (even AC IN) Remove the battery Pick the battery from the bottom, and lift to remove. Charging the battery Before using the terminal for the first time, you need to charge it for about 24 hours. For the regular use, you can charge the terminal for 4.5 hours to recharge the battery to full capacity. To charge the terminal, please use the USB charging cable or the cradle. Connect the type-C USB cable to the USB port on HT330 and the other end of the USB cable connect to AC power adapter into the electrical outlet on the USB plug. The charging LED indicator on HT330 is turning red when it is in charging state.