Champions By Design
Team Associated (@teamassociatedrc) • Instagram photos and videos
Installation Guide for ASSOCIATED ELECTRICS models including: RC10GT 1 10 Scale Gas Off Road Truck, RC10GT, 1 10 Scale Gas Off Road Truck, Scale Gas Off Road Truck, Gas Off Road Truck, Off Road Truck, Road Truck
TEAM ASSOCIATED RC10GT TEAM TRUCK KIT #AS7066
File Info : application/pdf, 22 Pages, 11.85MB
DocumentDocument2 :: Introduction Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new RC10GT Kit. Please take a moment to read through this manual to help familiarize yourself with these steps. We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags. Check each bag for these sheets before you start to build. :: KIT Features Features in the RC10GT Kit: · Exclusive Gold Aircraft aluminum tub chassis · Stealth ATC Transmission, optimized for gas truck racing, 2.6:1 reduction · Powerful rear disk brakes · Adjustable Slipper clutch · 2-second, quick fill fuel tank with filter · Heavy-duty front and rear arms · Reversible bellcrank / servo-saver steering · Vintage multi-surface wide front tires · Vintage Spike rear tires · 3 piece front and rear wheels · Original Clear Lexan body · Gold Anodized, Oil filled shocks · Ball Differential · Dual Stage Air Filter system · Precision Bearings throughout · Original release white plastic parts · Adjustable Turnbuckles for camber and toe · Aluminum Engine Manifold (Non pull start) · Polished Exhaust pipe (Non Pull Start) · 2 Shoe Clutch system and flywheel (non pull start) :: Additional Your new RC10GT Kit comes as a kit. There are some items you will need to complete your kit (refer to website for suggestions): · RC two channel surface frequency radio system · .12 non-pull start engine · Nitro fuel · Steering servo · Throttle servo · Starter box · Starter box battery · Receiver battery pack · Battery charger compliant to battery type · Polycarbonate specific paint · Thread Lock (AE #1596) Tools included: · Allen wrenches (.035", .050", 1/16", 3/32") · Shock building tool :: Other Helpful Items · Silicone Shock Fluid (Refer to website for complete listings) · FT 7-Piece 1/4 in Hex Driver Set (AE #1650) · Tire Adhesive (AE #1697) · Body Scissors (AE #1737) · Reamer / Hole Punch (AE #1499) · Shock Pliers (AE #1681) · Green Slime shock lube (AE #1105) · Calipers or a Precision Ruler · Wire Cutters / Hobby Knife · Needle Nose Pliers · Soldering Iron Associated Electrics, Inc. 21062 Bake Parkway Lake Forest, CA 92630 Customer Service Tel: 949.544.7500 Fax: 949.544.7501 http://www.AssociatedElectrics.com · · http://www.instagram.com/teamassociatedrc/ · http://www.facebook.com/TeamAssociated/ 3 :: Hardware - 1:1 Scale View Cap Head (shcs) Flat Head (fhcs) Button Head (bhcs) 4-40x1/4" 4-40x5/16" 4-40x3/8" 4-40x1/2" 4-40x5/8" 4-40x3/4" 4-40x1" Bearings / Bushings 1/8 x 5/16 x 1/16 Set Screws 5/32 x 5/16 x 1/8 (6589) 4-40x5/16" 4-40x3/8" 4-40x1/2" 4-40x3/4" 8-32x1/4" (6316) 8-32x1/2" (6316) Diff Balls 8-32x7/8" (6316) 4-40x3/16" 4-40x1/4" 4-40x5/16" 4-40x1/2" 4-4x5/8" 5/64 Thrust Balls (6574) 3/32 Diff Balls (6581) Shims and Washers 4-40x1/8" 4-40x5/16" Dogbone spacer .030 Nylon Spacer (4187) 1/4 x 3/8 x 1/8 (7359) 3/16 x 3/8 x 1/8 (3977) Nuts (lock/plain) 4-40 Small Pattern Plain Nut #4 Aluminum Washer 1/4" Axle Shim 3/16 x 5/16 x 1/8 4-40 Nuts Diff Thrust Washers (6573) 3/16 x 5/16 x 1/8 Flanged (6902) 3/8 x 5/8 x 5/32 (3976) Clips 5-40 Locknut 8-32 Steel Locknut E-clip 1/8" (6299) 5mm x 9.5mm 0.17mm #8 Aluminum Thick Washer Notes: 4 :: Table of Contents 1................... Cover 2................... Introduction 3....................1:1 Hardware "Fold Out" 4................... Table of Contents 5....................Nose Plate Build (Bag A) 7....................Servo Saver Build (Bag B) 7................... Transmission Build (Bag C) 9....................Rear End Build (Bag D, A) 11....................Shocks Build (Bag E) 13.................Turnbuckles Build (Bag F) 15.................Wheels / Tires Build (Bag G) 16.................Fuel Tank / Servo Build (Bag H, F) 17 ................Engine / Exhaust Install (Bag I) 18................ Throttle and Branke Links Build (Bag J) 20.................Fuel Tubing Install (Bag Misc) 20.................Air Fulter Install (Bag Misc) 20.................Receiver Battery Pack Install (Bag D, I, Misc) 21................ Antenna, Receiver, Body Install (Bag Misc) 22................Back Cover :: Notes ! This symbols indicates a special note or instruction in the manual. There is a 1:1 hardware foldout page in the front of the manual. To check the size of a part, line up your hardare with the correct drawing until you find the exact size. Associated Electrics, Inc. 21062 Bake Parkway Lake Forest, CA 92630 Customer Service Tel: 949.544.7500 Fax: 949.544.7501 http://www.AssociatedElectrics.com · · http://www.instagram.com/teamassociatedrc/ · http://www.facebook.com/TeamAssociated/ 12/24 :: Nose Plate / Steering Build - Bag A - Step 1 LEFT 4-40 thin nut 6273 Ballstud .30 (silver) Build left and right sides! 6213 RC10 front caster blocks, 15 degrees (Left & Right) 7810 Inline steering blocks, (Left & Right) 4-40 thin nut :: Nose Plate / Steering Build - Bag A - Step 2 LEFT 6299 x2 E-clip (small) 5 LEFT 6273 Ballstud .30 (silver) Inline steering axle 7813 RC10T king pin (.125 x .951) Build left and right sides! 4-40 set screw Build left and right sides! :: Nose Plate / Steering Build - Bag A - Step 3 LEFT 6299 x2 E-clip (small) x2 #4 aluminum washer x2 4-40 nut x2 4-40 nut thin 7806 RC10T front arms (Left & Right) Build left and right sides! 7813 RC10T king pin (.125 x 1.11) 7809 RC10T front bulkhead x2 4-40 x 3/4" SHCS 6271 Ballstud .20 (silver) 7537 RC10GT front shock tower x2 4-40 x 1/2" SHCS 6 :: Nose Plate / Steering Build - Bag A - Step 4 6299 x4 E-clip (small) x2 4-40 x 3/8 SHCS 7813 x2 Hinge pin (.125 x 1.675") 7809 x2 Front body mount 7809 RC10T bulkhead brace Build left and right sides! x2 4-40 x 1/2 BHCS :: Nose Plate / Steering Build - Bag A - Step 5 7809 Front body mount brace 7307 RC10GT nose plate, gold 7809 RC10T bumper 6316 x4 8-32 x 1/2 steel FHCS x2 4-40 x 5/16 FHCS :: Nose Plate / Steering Build - Bag A - Step 6 7308 RC10GT chassis, gold x2 4-40 nut 7306 8-32 x 1/4 steel FHCS :: Servo Saver Build - Bag B - Step 1 6271 x4 Ballstud .20 (silver) 6271 Ballstud .20 (silver) 7 Servo saver spring and collar 7255 Servo saver 7255 Servo saver :: Servo Saver Build - Bag B - Step 2 x2 5-40 locknut 3x7x0.5mm Washer 7540 RC10GT chassis brace tubes 7306 Servo saver screw, short FHCS 4-40 x 1/2 SHCS 7306 Servo saver screw, long FHCS :: Transmission Build - Bag C - Step 1 6581 x12 Carbide diff balls, 3/32" silicon#e6l5u9b1e 7664 Diff gear 52T 7666 Diff drive rings 6589 x2 Bearing 5/32 x 5/16 #6588 black grease 7668 RC10GT Diff outdrive 4-40 x 5/16 SHCS Build left and right sides! 6573 x2 Diff thrust washer 6574 x6 Diff thrust balls, 5/64" 6573 Diff thrust bolt 7667 Diff outdrive 7666 Diff drive rings 6582 Diff thrust spring 6575 Diff thrust nut 8 :: Transmission Build - Bag C - Step 2 6575 Diff bolt cover 6570 Idler gear and shaft 3976 x2 Bearing 3/8 x 5/8 3977 x4 Bearing 3/16 x 3/8 6571 Drive gear 7669 Driveshaft spacer :: Transmission Build - Bag C - Step 3 7661 RC10GT Transmission Case x5 4-40 x 3/8 SHCS 6584 Clutch outer hub 6583 Clutch hub 7661 RC10GT brake adapter 7665 Drive shaft roll pin x2 4-40 x 3/16 BHCS 7663 Spur gear, 64T, 32P 6585 Slipper disk 7553 Brake disk :: Transmission Build - Bag C - Step 4 Bearing 3/16 x 5/16 Slipper washers Diff spring 5-40 Locknut 1/8 x 5/16 bushing 7538 Brake bracket 7538 Brake shoe :: Transmission Build - Bag C - Step 5 brake bracket brake disc ! INSTALL BRAKE BRACKET brake shoe 1) Slide the bracket assembly onto the transmission. Make sure the brake disc is centered between the bracket and brake shoe as shown. 2) Secure the bracket to the transmission as shown, using two 4-40 x 5/16 BHCS screws in the top holes of the brake bracket. 7538 Brake cam clip :: Rear End Build - Bag D - Step 1 6299 x2 E-clip (small) 7533 RC10GT rear arm mounts 7806 RC10T rear arms 7813 Hinge pin rear inner Build left and right sides! :: Rear End Build - Bag D - Step 2 7625 Engine mount, front 7625 Engine mount, rear 9 7538 Brake cam x2 4-40 x 5/16 BHCS 6316 x2 8-32 x 1/2 steel FHCS x7 4-40 x 3/8 FHCS x4 4-40 x 3/8 FHCS x2 4-40 x 7/8 FHCS 10 :: Rear End Build - Bag D - Step 3 7535 RC10GT rear bulkhead x2 4-40 thin nut 6273 x2 Ballstud .30 (silver) 7541 RC10GT rear univeral drive shaft 7359 x2 Bearing 1/4 x 3/8 x3 1/4 axle shims 6316 x2 8-32 x 1/2 steel FHCS 7810 RC10T rear hub carrier, 0 degree (Left & Right) Build left and right sides! :: Rear End Build - Bag D - Step 4 7661 RC10GT transmission brace x4 4-40 x 3/8 SHCS 6374 Roll pins .1 dia x 3/8 7813 Hinge pin rear outer :: Rear End Build - Bag D (bag A for rear body mounts & screws - Step 5 RC10GT rear tower x2 4-40 nut 6299 x2 E-clip (small) 7809 x2 Rear body mounts x2 4-40 x 3/8 SHCS x2 4-40 x 1/4 SHCS x2 4-40 x 3/4 SHCS :: Rear End Build - Bag D - Step 6 7535 RC10GT rear bumper 11 x2 4-40 nut x4 4-40 x 3/8 SHCS :: Shocks Build - Bag E - Step 1 Remove spurs 6299 E-clip Piston (small) 2 Piston number here Use #3 = front shocks Use #2 = rear shocks TIP: Use marker ! to mark the piston numbers for easy identification! 6421 Shock shaft, front (1.02) 6420 Shock shaft, rear (1.32) :: Shocks Build - Bag E - Step 2 5407 x2 Red o-ring 6420 / 6421 x2 Off-road shock internals 6421 Shock body, front (1.02) Gold Remove spurs 30Swhot c#k5f4lu2i2d Shock assembly tool x2 4-40 x 3/8 FHCS Shock pistons (1, 2, 3) 6299 E-clip (small) Build two front and two rear! Front Shock 6420 Shock body, rear (1.32) Gold SNAP! 30Swhot c#k5f4lu2i2d Rear Shock ! Place on table and push down hard until clamp snaps into place SNAP! 12 :: Shocks Build - Bag E - Step 3 Front Shock Rear Shock 6420 / 6421 x2 Shock downstops 6420 / 6421 Shock cap o-ring 6420 / 6421 Shock pivot ball 6420 / 6421 Shock rod end Build two front and two rear! :: Shocks Build - Bag E - Step 4 S3h0owctk#f5lu4i2d2 30Swhot c#k5f4lu2i2d 6420 / 6421 RC10 shock cap Gold Step 1-3 Step 3-4 Step 5-6 Step 7 * Shock Bleeding Steps: 1. Pull shock shaft down. 2. Fill shock body 3/4 full with silicone fluid. 3. Slowly move the shock shaft up and down to remove air from under piston. 4. Wait for bubbles to come to surface. 5. Fill shock body to top with silicone fluid. 6. Place several drops of oil in the cap and on cap threads. 7. Install cap and tighten completely. 8. Slowly compress shaft all the way to the top. If there is pressure at the top of the stroke, there is too much oil. You must bleed it out. 9. Slowly pull shaft down. 10. Unscrew the cap 3/4 turn and tilt the shock at a slight angle. 11. Slowly compress the shaft to push out excess oil and air. You should see bubbles coming out from under the cap. 12. With the shaft compressed, tighten the cap and re-check for pressure at the top of the stroke. If there is still pressure, repeat steps 9 thru11. :: Shocks Build - Bag E - Step 5 6420 / 6421 RC10 shock collar 4-40 x 3/8 SHCS Front shock spring, Gold (3.70lb) Rear shock spring, Gold (3.70lb) *Ride height setting may change due to varying weight of batteries and electronics Front: 10mm Rear: 5mm (rear dogbones level) 6420 / 6421 RC10 spring cup Build two front and two rear! :: Shocks Build - Bag E - Step 6 #4 aluminum washer RC10 shock bushing 4-40 locknut 13 Build left and right sides! :: Shocks Build - Bag E - Step 7 4-40 x 5/8 SHCS #4 aluminum washer RC10 shock bushing 7533 RC10GT rear arm shock mounts Build left and right sides! 4-40 locknut x2 3.1x5.5x2mm Washer x2 4-40 x 5/8 SHCS 4-40 x 1/2 SHCS :: Turnbuckles Build - Bag F - Step 1 6279 x2 Ball cups (white) Build left and right sides! Turnbuckle (1") Bellcrank Turnbuckle 0.53" (13.5mm) 14 :: Turnbuckles Build - Bag F - Step 2 6279 x2 Ball cups (white) 7253 Turnbuckle (2.62") Front Camber Turnbuckle 1.95" (49.5mm) Build left and right sides! :: Turnbuckles Build - Bag F - Step 3 Recommended turnbuckle lengths are approximate. Final recommended settings = 0 degree Front Toe in and -2 Degree Camber Front and Rear. 6279 x2 Ball cups (white) ! Orient the notch to the left throughout the car. It indicates which end has the left hand threads! 7253 Turnbuckle (2.62") Steering Turnbuckle 2.14" (54.5mm) Build left and right sides! :: Turnbuckles Build - Bag F - Step 4 4-40 nut Recommended turnbuckle lengths are approximate. Final recommended settings = 0 degree Front Toe in and -2 Degree Camber Front and Rear. 6279 Ball cups (white) 7253 Turnbuckle (2.62") Shock rod end Shock pivot ball Rear Camber Turnbuckle 1.98" (50.5mm) Build left and right sides! 4-40 x 5/8 SHCS Recommended turnbuckle lengths are approximate. Final recommended settings = 0 degree Front Toe in and -2 Degree Camber Front and Rear. ! Orient the notch to the left throughout the car. It indicates which end has the left hand threads! ! Orient the notch to the left throughout the car. It indicates which end has the left hand threads! :: Wheel and Tire Build - Bag G - Step 1 7840 RC10GT front wheel, wide, inner 7870 RC10GT front tires, wide Build 2 Tir#e1a6d9h7esive 7840 RC10GT front wheel, wide, outer :: Wheel and Tire Build - Bag G - Step 2 7807 RC10T rear wheel, inner Tir#e1a6d9h7esive 7871 RC10T rear tires Build 2 7807 RC10T rear wheel, outer :: Wheel and Tire Build - Bag G - Step 3 15 TIP: It is recommended to glue the tire beads to the wheels! 7840 RC10GT front wheel, wide, spacer ! Do not overtighten wheel screws! 7807 x4 4-40 x 5/8 SHCS TIP: It is recommended to glue the tire beads to the wheels! 7807 RC10T rear wheel, wide, spacer ! Do not overtighten wheel screws! 7807 x4 4-40 x 3/4 SHCS x2 8-32 steel locknut 3977 x2 Bearing 3/16 x 3/8 Build left and right sides! x2 5-40 locknut Build left and right sides! 16 :: Fuel Tank / Servo Build - Bag F / H - Step 1 6279 x2 Ball cups (white) 7534 x2 Steering servo mounts 6261 Turnbuckle (1.25") Servo Turnbuckle 0.70" (18mm) x4 #4 aluminum washer x4 4-40 x 3/8 SHCS :: Fuel Tank / Servo Build - Bag H - Step 2 Servo not included! 4-40 nut, thin 6273 Ballstud .20 (silver) Servo horn and screw not included! 7534 Reciever mount 7534 x2 Throttle/brake servo mounts x2 4-40 x 3/8 FHCS x2 4-40 x 5/16 FHCS :: Fuel Tank / Servo Build - Bag H - Step 3 Servo horn and screw not included! x2 4-40 x 5/16 SHCS x2 #4 aluminum washer Servo not included! 7719 RC10GT Fuel tank 5407 x3 Red o-ring x3 4-40 x 5/16 FHCS :: Engine / Exhaust Install - Bag I - Step 1 x2 4-40 x 1/2 SHCS 7625 Engine adapter, rear x4 #4 aluminum washer 7625 Engine adapter, front x2 4-40 x 5/8 BHCS :: Engine / Exhaust Install - Bag I - Step 2 Engine not included! 17 Flywheel shim 7603 RC10GT clutch nut 7601 x2 RC10GT clutch shoes Flywheel 7610 washer RC10GT 2-shoe flywheel Carb not included! 6902 x2 3/16 x 5/16 bearing, flanged 7605 RC10GT clutch bell, 15T - 32P :: Engine / Exhaust Install - Bag I - Step 3 Engine Installation. Line up your engine with the clutch assembly and flywheel assembly in your engine mount. Center your engine on your mount. Now fasten the motor to the mount with four screws. Do not tighten yet! x4 4-40 x 3/8 SHCS 7603 Clutch nut e-clip Check gear mesh. Set the gear-to-pinion gear spacing (gear mesh). Make sure you can still slide your engine mount, then mesh the clutch bell pinion with the spur gear. The correct gear spacing is when the pinion is as close to the spur gear as possible, but if you hold the pinion gear, you should still be able to rock the spur gear back and forth slightly with light pressure. Roll the gears and check the mesh in several different locations on the spur gear teeth to check if the spur gear is slightly out of round. 18 :: Engine / Exhaust Install - Bag I - Step 4 7734 Manifold gasket 4-40 locknut 5407 Exhaust manifold, non-pull start #4 aluminum washer 7728 RC10GT tuned pipe x2 Zip ties 7733 RC10GT exhaust coupler x2 4-40 x 1 SHCS 4-40 x 3/8 FHCS 7728 RC10GT tuned pipe bracket :: Throttle and Brake Links - Bag J - Step 1 7560 x2 Collar 7560 Throttle pivot 7560 Throttle spring 7560 x2 2.3 x 6 self tapping screws 7534 Throttle / brake servo horn 7560 2-56 throttle rod 7560 Brake cam clip 7560 x2 4-40 x 1/8 set screw 7560 2-56 ball end Install your stock servo horn to your servo with the stock servo screw. (You may have to trim away a part of your stock servo horn so the locking collar for the brake linkage in Step 9 won't hit it.) Mount the #7560 aluminum throttle pivot to the #7534 adapter with the #7560 throttle pivot clip, with the clip's inner teeth flaring away from the adapter. Screw one #7560 ball cup onto the end of the #7560 throttle rod. Slide on one #7560 collar about an inch away from the ball cup and tighten it down with a #7560 set screw. Slide on the #7560 long throttle spring. Slide the throttle rod through the throttle pivot, then slide on and fasten the second #7560 collar to the rod so there is about one inch (xxmm) of space between collars. Attach the servo horn adapter assembly to your servo horn with the two #7560 screws provided. See photo for proper orientation of adapter to your servo. Snap the ball cup onto the carb's ball end. Cut off the remaining part of the throttle rod. Make sure you leave 1/2 inch (12.7mm) so you can adjust the throttle linkage. :: Throttle and Brake Links - Bag J - Step 2 BRAKE LINKAGE 1) Add a #7560 collar onto the second rod and secure it about 3/8" (9.53mm) from the end of the threads. See drawing below. 2) Bend the brake rod according to the actual size drawing below, including the angled bend at the short side. Cut the rod to the length shown. 3) Slide the threaded end of the rod through the disc brake cam. Drop the bent end of the brake rod through the adapter hole shown. Attach a #7560 collar with a #6591 set screw to the end of the rod. 4) Slide on another 7560 collar with #6951 set screw, a #7560 7560 washer, then the #4118 spring, then the #7560 locknut. 5) Tighten the locknut down until shown in the picture. Brake rod spring 7560 2-56 Steel locknut 0.375" (9.53mm) #4 aluminum washer 7560 x2 Collar 7560 Disk brake cam 19 7560 x2 4-40 x 1/8 set screw :: Throttle and Brake Links - Bag J - Step 3 IDLE SETTING carb almost closed Adjust the throttle linkage 1) Turn on your transmitter then the kit's electronics (don't start the engine). When at idle (trigger of transmitter not pulled), adjust the collar near the adapter so there is up to1/16" (1.58 mm) of space between the collar and pivot. FULL THROTTLE carb fully opened 2) Apply full throttle (pull the trigger of your transmitter all the way back). Your carb should be fully open. If it is not, then adjust the collar nearest to the adapter. (You may also adjust your throttle trim according to your radio's instructions.) 3) Now apply the brake. Your carb should be at idle position. The spring should not be completely compressed. BRAKE APPLIED carb almost closed 1) Small gap here 2) 3) Should not be fully compressed 4) IDLE SETTING 5) FULL THROTTLE 6) BRAKE APPLIED carb almost closed carb fully opened carb almost closed 4) Small gap here 6) 20 :: Fuel Tubing Install - Bag Misc. - Step 1 FUEL TUBING Slide one end of the #7724 fuel tubing onto the fuel tank outlet fitting. Bring the other end of the tubing over to the other fitting. When you have the correct length without kinks in the tubing or rubbing against other parts of the truck, then mark the fuel tubing and cut it to that length. Again check to make sure the fuel line clears the spur gear or any other parts. Install the tubing into the fitting on the top of the fuel tank. Take one of the small wire ties and loop it around the muffler bracket, leaving as large a loop in it as possible. Take your fuel tubing and run it through the wire tie, then loop it around and bring it back through the same side of the wire tie again. Now take the end of the tubing and squeeze it into the hole in the tuned pipe muffler about 3/8". Now tighten the wire tie, but not so tight that it will begin to compress the tubing. Cut off the end of the wire tie. :: Air Filter Install - Bag Misc. - Step 1 7542 x2 Air filter foam 7542 Air filter boot Zip tie the air filter boot to the carb. ! Pre-lube the air filter outer elements :: Receiver Battery Pack - Bag D, I, Misc. - Step 1 x2 Zip ties 7535 Foam pad Receiver battery not included! Run zip ties thru the openings of the rear bumper and around the receiver battery pack as shown. :: Antenna, Receiver, Body Install - Step 1 6338 Antenna tube and cap Receiver not included! 6727 Servo tape :: Antenna, Receiver, Body Install - Step 2 Painting Tips: Your RC10T Kit comes with a clear polycarbonate body and wing. You will need to prep the body and wing before you can paint them. Wash the inside thoroughly with warm water and liquid detergent. Dry the body and wing using a clean, soft, lint-free cloth. Use high quality masking tape to make masks for the windows and install them on the inside of the body (RC cars get painted from the inside). Using high quality masking tape, apply tape to the inside of the body to create a design. Spray (either rattle can or airbrush RC specific paint) the paint to the inside of the body (prefferably dark colors first, lighter colors last). NOTE: use ONLY paint that is recommended for use with (polycarbonate) plastics. If you do not, you can destroy the plastic body and wing!). It is recommended to wear a mask while painting. After the paint has dried, cut the body and wing along the trim lines. Make sure to drill or use a body reamer to make the holes for the body mounts, wing mounts, and antenna! 21 x3 4-40 x 5/16 BHCS 6131 RC10GT wing 6131 RC10GT body, clear x3 4-40 locknut 6332 x4 Body clip x4 Body mount washers