tendacn.comCE Center_Tenda-All For Better NetWorking
Installation Guide for Tenda models including: 4G185 4G LTE Mobile Wi-Fi Hotspot, 4G185, 4G LTE Mobile Wi-Fi Hotspot, LTE Mobile Wi-Fi Hotspot, Mobile Wi-Fi Hotspot, Wi-Fi Hotspot, Hotspot
Tenda 4G Mobile Hotspot, 4G LTE Cat4 150Mbps MiFi Device, 4G Router, Support USB Interface Charging|2100 MAh Battery, No Configuration Required (4G185), Black : Electronics
4G185 Installation Manual (PDF) Tenda Tenda Tenda,4G,Mobile,Hotspot,4G,LTE,Cat4,150Mbps,MiFi,Device,Router,with,USB,Charging,&,2100mAh,Battery,No,Setup,Required,(4G185),Black,,
File Info : application/pdf, 10 Pages, 3.19MB
DocumentDocumentQuick Installation Guide 4G LTE Mobile Wi-Fi 4G180 & 4G185 Package content · Mobile Wi-Fi × 1 · Li-ion battery × 1 · USB cable × 1 · SIM Card Adapter× 1 · Quick installation guide × 1 For product or function details, please go to www.tendacn.com to download the user guide. LED indicators/LCD Screen 4G180 LED Status Solid green Signal Blinking green Solid red Solid green Blinking green Battery Solid red Blinking red Blinking green for 5 times Message Solid green Off Solid on Wi-Fi Blinking Off Description Connected to the internet. Signal detected, but no internet access. No signal. Remaining battery percentage is above 25%. Charging the battery. Remaining battery percentage is between 20% and 25%. Remaining battery percentage is below 20%. New SMS message is received or the storage is full. There are unread SMS messages. No unread SMS messages. No device is connected to the Wi-Fi network. There is at least one devices connected to the Wi-Fi network, or a WPS negotiation is in process. The Wi-Fi network is disabled. 1 4G185 1 2 3 4 5 6 7 8 1. Data type and signal strength 2. Battery meter 3. Wi-Fi status and connected Wi-Fi clients 4. Operator name 5. Message status 6. Operator name/Tip information 7. Internet connection duration 8. Used data traffic 2 Buttons/Ports/Slots 1 2 4 3 5 6 No. Buttons /Port/Slot Description Power button. Hold it for about 3 seconds to turn on/off the Hotspot. 1 Press it once to turn on its LED indicators/LCD screen. Tips When the LCD screen of 4G185 is on, press it once to show the SSID and Wi-Fi key. Press it twice to show a QR code of the Wi-Fi information. 2 WPS 3 Reset WPS button. When the WPS function is enabled: 4G180: The Wi-Fi LED indicator will blink. 4G185: WPS Active will be shown on the LCD screen. Hold the button down for about 3 seconds to enable the WPS function. Enable the WPS function on a WPS-supported device to establish a WPS negotiation. Reset button. Hold the button using a sharp object for about 6 seconds to reset the Hotspot. 4 SD card slot Insert your SD card here to increase storage space. 5 SIM card slot Insert your SIM card here. 6 Charging/ Micro USB port Used to charge the Hotspot, or to provide wired device internet access using the USB cable. 3 Install SIM card and battery 4G LTE Mobile Wi-Fi SSID: Tenda_xxxxxx Wi-Fi Key: xxxxxxxx Open from the lower left corner Slide and flip to open 4G LTE Mobile Wi-Fi Metal connectors 4 Turn on the Hotspot Hold the button till all LED indicators flash once (4G180) or the LCD screen lights up (4G185). When the Hotspot is connected to the internet, you will find: Solid green Data type and signal strength 4G180 4G185 Tips If the Hotspot is not connected to the internet after a long time, refer to Q1 in FAQ. 5 Access the internet To access the internet through the Hotspot: Wireless: Connect your wireless device to the Wi-Fi network of the Hotspot with the SSID and Wi-Fi key at the top of the device after opening the back cover. Wired: Connect a PC or laptop to the Hotspot using the USB cable. You can log in to the web UI by visiting 192.168.0.1 to further configure the Hotspot. Tips For a new computer connected in a wired manner for the first time, you need to double-click the CD drive installed on the computer before you can access the internet. If you cannot access the internet, refer to Q2 in FAQ. If you cannot log in to the web UI, refer to Q3 in FAQ. 6 Charge your Hotspot Method 1: Connect to a computer Method 2: Connect to a power socket 7 FAQ Q1: The Hotspot is not connected to the internet after a long time. What should I do? A1: Try the following solutions: Ensure that your SIM card is pre-paid and have enough balance. Check if your SIM card is locked with a PIN code. If so, contact your ISP for the PIN code, visit the web UI (default: 192.168.0.1) on a connected device, and follow the instruction on the web UI to unlock the SIM card. Try another SIM card. Reset the Hotspot. Q2: I cannot access the internet. What should I do? A2: Try the following solutions: Ensure that the Hotspot is connected to the internet. if not, refer toQ1. Ensure that your wireless device is connected to Wi-Fi network of the Hotspot. Try with your wireless device closer to the Hotspot. Ensure that your wired device is connected to the Hotspot properly and set to obtain an IP address automatically. Q3: I cannot log in to the web UI. What should I do? A3: Try the following solutions: For wireless devices: - Ensure that you connect your device to the Wi-Fi network of the Hotspot. - Ensure that you have disabled the mobile data (if any) of your wireless device. For wired devices: Ensure that the wired device, such as a computer, obtains an IP address automatically. Ensure that you entered 192.168.0.1 correct in the address bar of a browser. Try another browser or with another device. If the problem persists, reset the Hotspot and try again. Q4: How to change the Wi-Fi name (SSID) and Wi-Fi key? A4: Follow the steps below: Start a web browser on a connected device and visit 192.168.0.1 to log in to the web UI. Enter the login password (default: admin) and click Login. Find Network Settings and choose Wi-Fi Settings. Change Network Name (SSID) and Wi-Fi Key (or Pass Phrase) as required. Q5: How to reset the Hotspot? A5: Follow the steps below: Remove the back cover. Find the Reset hole in the lower part of the Hotspot. Hold the button using a sharp object for about 6 seconds. 8 CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This equipment should be installed and operated with a minimum distance 20cm between the device and your body. NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable. Declaration of Conformity Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the radio equipment type 4G180/4G185 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.tendacn.com/en/service/download-cata-101.html Operating Frequency: 2.4 GHz: EU/2400-2483.5MHz (CH1-CH13) EIRP Power (Max.): 2.4 GHz: 12.64dBm Software Version: V3.1_SM_FX_TD_P032 RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. Operating Temperature: 0°C - 40°C Operating Humidity: (10% - 90%) RH, non-condensing Caution: Battery Model: 4G Manufacturer: Shenzhen Powercome Electronics Co., LTD 9