User Manual for NEXELO models including: C20WLS, Sports Testers, C20WLS Sports Testers, Testers
Cycling Computer Nexelo CX20 - inSPORTline
File Info : application/pdf, 5 Pages, 171.81KB
DocumentDocumentNEXELO C20WLS Remove the protective foil form display. 20 functions: 1. 12/24 hour format 2. Stopwatches 3. Backlight 4. Current speed (SPD) 5. Average speed (AVS) 6. Maximum speed (MAX) 7. Current time session (TM) 8. Total daily distance (DST) 9. Total distance (ODO) 10. Auto off 11. Auto scan (SCAN) 12. Set kilometers (CDD) 13. Time countdown (CDT) 14. Theoretical daily calorie consumption (CAL) 15. Theoretical daily fat consumption (FAT) 16. Thermometer 17. Low battery indicator 18. +/- Comparison of average and current speeds 19. Signalling of service intervals 20. Number of laps Battery installation Insert the CR2032 battery into the computer. Note: the positive pole (+) should be set upwards. Follow the same procedure for the transmitter. Bracket attaching Attach the computer bracket with the tab on the back of the computer. Then insert the computer into the holder and turn it to the right. Sensor and magnet installation. Install the sensor on the front fork and then the magnet on the wheel spoke, on the side of the sensor. Both the sensor and the magnet should be installed 60 cm from the computer. Then adjust the distance between the sensor and the magnet to 1.5 mm. The computer should now display the values when the wheel is spinning. If not, try adjusting the distances again. Tire circumference adjustment After inserting the battery into the computer, the value 2060 will appear on the screen, with the first number flashing - the computer is ready to set the tire circumference, according to the following table. Use the right button to change the value of the currently flashing number, use the left button to confirm this value and advance to the next number. Then press the left button again to go to the Km/h, Miles/h mode setting Tire circumference table Tire size 47-305, 16 x 1.90 47-406, 20 x 1.75 37-540, 24 x 1 3/8 47-507, 24 x 1,75 37-584, 26 x 1 3/8, 650 STD 37-590, 26 x 1 3/8, 650x35A 40-559, 26 x 1,50 42-559, 26 x 1,60 47-559, 26 x 1,75 50-559, 26 x 2,00 54-559, 26 x 2,10 57-559, 26 x 2,25 57-584, 27 x 1/2x2,25 28-630, 27 x 1 1/4 32-630, 27 x 1 1/4 40-635, 28 x 1 1/2 Diameter 1272 1580 1948 1900 2086 2100 2030 2025 2050 2075 2100 2120 2128 2174 2220 2265 Tire size 32-622, 28 x 1,25, 700x32C 35-622, 28 x 1,35, 700x35C 37-622, 28 x 1,40, 700x35C 37-622, 28 x 1,40, 700x37C 40-622, 28 x 1,50, 700x38C 42-622, 28 x 1,60, 700x40C 47-622, 28 x 1,75 50-622, 29 x 2,00 54-622, 29 x 2,10 57-622, 29 x 2,25 60-622, 29 x 2,35 23-571, 650 x 23C 18-622, 700 x 20C 20-622, 700 x 23C 23-622, 700 x 23C 25-622, 700 x 25C 28-622, 700 x 28C Diameter 2170 2185 2200 2200 2220 2230 2250 2280 2295 2288 2330 1973 2102 2100 2125 2135 2150 KM/h or M/h setting Use right button to select KM/h or Miles/h mode. Press the left button to go to the weight setting. Weight setting K (Kg) and the pre-set value 065 light up on the screen. Set your weight between 20-200Kg and confirm by pressing the left button. Pressing the same button again will then switch to setting of a maintenance reminder. Maintenance reminder settings Use right button to select the interval 200, 400, 600, 800 KM, after which the flashing wrench symbol appears on the screen. Press the right button for 3 seconds to turn off this reminder. Then use the left button to go to the clock setting. 12H / 24H format setting Press the left button for 3 seconds, switch with the right button between 12 and 24 h mode, confirm with the left button. Then press the right button to go to the time setting. Use the left button to change the value of the currently flashing number, one by one or the right to change from setting hours to minutes. Then you go to the setting of the total km. Switching between functions Press the right button to switch between the individual functions: (ODO) - (DST) - (MAX) - (AVS) - (TM) - (SW) - (CDD) - (CDT) - (CAL) - (FAT) - (TEM) - (SCAN) ODO settings Hold down the left button for 3 seconds, then use the right button to change the value of the currently flashing number and confirm with the left button. Then press the right button to switch to daily distance (DST). DST DST expresses the distance reached in single training, ranging from 0.001 to 9999 (KM). When this, the maximum limit is exceeded, it is automatically reset. Pressing the left button in DST mode resets the recorded DST value, along with the recorded MAX, AVS, TM values. Press the right button to enter the maximum speed mode. MAX In MAX mode, the maximum speed of single training is recorded. Pressing the right button in MAX mode resets the recorded MAX value, along with the recorded DST, AVS, TM values. Right click switch to AVS mode AVS In AVS mode, the current average speed of single training is recorded / displayed. Press the left button for 3 seconds to reset the AVS value, along with the recorded DST, MAX, TM. Press the right button to switch to TM mode. TM In TM mode, the current duration of the current training is displayed, in the range 0:00:00 to 99:59:59. When this maximum value is exceeded, the recorded TM value is automatically reset, along with the DST, MAX and AVS values. Pressing the left button for 3 seconds will then reset these values manually. Press the right button to enter SW mode SW SW = stopwatch. Use the left button to start, the left button to pause, the right button to reset the recorded value. By pressing the left button for 3s, the computer will be locked in stopwatch mode (no other function can be used), then press the same button for 3 s to cancel this setting. Right-click to enter CDD mode. CDD Hold down the left button for 3s and set the desired value in the range 0-999.99 Km. Right-click to confirm. Right-click to enter CDT mode. CDT In CDT mode, the travel time of the distance / section selected within the CDD function is displayed / recorded. Right-click to enter CAL mode. CAL CAL shows the number of calories burned in one trip. If you press the left button for 3's, it will be cleared, along with the recorded FAT values. Right-click to enter FAT mode FAT Display number of burned fat. Right-click to enter TEM mode TEM TEM = ambient air temperature. Press the left button for 3s and set the preferred C/F unit. Right-click to enter SCAN mode SCAN In SCAN mode, the DST, MXS, AVS, TM values are displayed on the screen one by one. Lap measurement Left click to enter FFM mode. The value is displayed (TM). Pressing the right button then switches from this to the values (DST), (TM) , (AVS), (MAX). The left button then exits this mode. Current speed The current speed value is always displayed on the screen. A comparison of the current and current average speed "+" or "-" is always displayed in the upper right corner. Depending on whether your current speed is higher or lower than your current average speed. Backlight The screen always lights up for 6 seconds when any button is pressed. Pressing the right and left buttons simultaneously for 3 s will turn on backlight permanently, repeat to turn off. Automatic shutdown The computer always enters sleep mode if it does not receive any signals for more than 5 minutes. The flashing battery symbol is displayed, if necessary to replace the battery. ERRORS AND POSSIBLE CAUSE Malfunction Cause Permanently displayed values 0 Incorrectly set distance between computer - sensor, sensor - magnet. Incorrectly measured values Slow reactions Blank screen Black screen 3 incorrectly set default values, eg wheel circumference Deceleration due to low ambient temperature. Lover visibility due to direct sunlight Direct sunlight Accesories Computer bracket Magnetic sensor Battery Magnetic sensor Zip tape http://www.nexelo.eu/