User Guide for NEXTIVITY models including: R41-9B-001, R41-9B-002, R41-9B-003, R41-YB-001, R41-YB-002, R41-YB-003, CEL-FI ROAM R41, CEL-FI ROAM R41 Smart Mobile Repeater, Smart Mobile Repeater, Mobile Repeater, Repeater
ROAM R41 - Nextivity
Quick Start Guide. Included In the Box. R41-9B-001. R41-9B-002. R41-9B-003. KIT#:. R41-YB-001. R41-YB-002. R41-YB-003. Mounting Hardware. Ground Cable.
ROAM R41 Quick Start Guide KIT#: R41-9B-001 R41-9B-002 R41-9B-003 R41-YB-001 R41-YB-002 R41-YB-003 Included In the Box Main Unit Automobile Auxiliary Power Adapter Mobile Donor Antenna* Server Antenna* Mounting Hardware Ground Cable Quick Installation IMPORTANT: Your CEL-FI GO G41 is electronic equipment. The CEL-FI GO G41 must be kept indoors and in a dry, cool, well ventilated area. 1 Install Donor Antenna Donor Antenna 2 Install the Server Antenna Server Antenna Mount your Donor Antenna on the exterior and towards the rear of your automobile or boat, depending on the design and type of vehicle. Make sure you consider the cable connection to the Main Unit with your location choice. Note: For best performance, ensure there is 50 cm of metal around the base of the antenna. 3 Select the Main Unit Location Main Unit Donor Port Install the Server Antenna in the cabin/deck towards the front of the vehicle where coverage is needed. Make sure to mount the Server Antenna horizontally. Note: The Donor Antenna should be separated/isolated as far away as possible from the Server Antenna, greater separation provides the best performance. 4 Attach Server and Donor Antennas Server Port Find a suitable location to securely mount the Main Unit. When installed, the Main Unit should have airflow and be in a position that doesn't contact other objects. Make sure the location provides enough distance for all the cables to connect. It's best to ensure all cables reach desired locations BEFORE mounting the device. 5 Install Ground Cable Drip Loop Attach the Donor Antenna and Server Antenna to the Main Unit. Note: Adding a drip loop to the Donor Antenna cable is crucial as it prevents water from flowing down the cable and damaging the Main Unit's electronic equipment. 6 Plug in the Main Unit Using the provided M3 screw, attach one end of the ground cable to the Main Unit and the other end to the chassis of the automobile or boat. Using the provided M3 screw, attach one end of the ground cable to the Main Unit and the other end to the chassis of the automobile or boat. 7 Nextivity WAVE Software Download the WAVE App to monitor and manage the status of your ROAM R41. Scan to Download Marine Installation Grounding Cable ROAM R41 Power Source Drip Loop Download the MyWave App to set your ROAM R41 to automatically track the base station to which your phone is connected. Scan to Download Server Antenna Model# R41-YB R41-9B Bands Supported Link Output Power (dBm) 1/3/5/7/8/26/28L Downlink Uplink 0 22 1/3/7/8/20 Downlink Uplink 0 22 Power/Status LED Indicator LED Behavior No light Solid Orange Slow blinking green Solid Green Solid Red Flash RED 1 time & OFF for 4sec Flash RED 2 times & OFF for 4sec Flash RED 3 times & OFF for 4sec Flash RED 4 times & OFF for 4sec Flash RED 5 times & OFF for 4sec Flash RED 6 times & OFF for 4sec Flash RED 7 times & OFF for 4sec Translation/Error State Device is powered OFF Device is powered ON Device is booting up Device is band scanning to acquire network signals Device is operating normally and providing coverage Hardware Error (ES1)Disconnect & Reconnect Device is not receiving signal from the cellular network (ES2) Donor input signal is too strong for the device (ES4) Device's server antenna is too close to donor antenna (ES7) Device is disabled by the operator (ES9) Device location lock pending (ES10) Device registration pending (ES11) Device Self-Test Failed (ES12) qsg-R41_eng_23-0421 Copyright © 2023 by Nextivity, Inc., U.S. Patents pending. All rights reserved. The Nextivity and CEL-FI logos are registered trademarks of Nextivity, Inc. All other trademarks or registered trademarks listed belong to their respective owners. Designed by Nextivity, Inc. in California.Adobe PDF Library 17.0 Adobe InDesign 18.3 (Windows)