EK Lights
User Manual for EK models including: EPROFILE HP, EPROFILE HP LED Profile Spot Light, EPROFILE HP, LED Profile Spot Light, Profile Spot Light, Spot Light
The EPROFILE HP is a high-output LED pro˜le. - 200W LED with extremely high light output LED Frequency
EPROFILE HP - EK Lights
File Info : application/pdf, 12 Pages, 3.85MB
DocumentDocumentLED PROFILE SPOT - HIGH POWER
2
WARNING! Before carrying out any operations with the unit, carefully read this instruction manual and keep it with cure for future reference. It contains important information about the installation, usage and maintenance of the unit.
SAFETY
General instruction
· The products referred to in this manual conform to the European Community Directives and are there-
fore marked with .
· The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.
Never make
risk an electric shock. ·
cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units
from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
installer. Check that the main frequency and voltage correspond to those for which the unit is designed as given on the electrical data label. · This unit is not for home use, only professional applications.
- in places subject to vibrations or bumps; - in places with a temperature of over 40 °C.
an inspection or contact the manufacturer directly. plant for a disposal which is not harmful to the environment.
Warnings and installation precautions
damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like
short circuit, burns, electric shock, etc.
· Always additionally secure the projector with the safety rope. When carrying out any work, always comply scrupulously with all the regulations (particularly regarding safety) currently in force in the country
· Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent · The lamp (LED) shall be changed if it has become damaged or thermally deformed.
trigger epileptic seizures in photosensitive persons or persons with epilepsy. · Do not touch the product's housing when operatingbecauseitmaybevery hot.
3
TABLE OF CONTENTS
Safety General instructions
Warnings and installation precautions
General information
Introduction
Features
Specifications
Maintenance Cleaning the unit Fuse replacement Trouble shooting
Overview Dimensions
Operation Display menu functions DMX functions DMX pin diagram
Menu Function Chart
Photometrics
DMX Function Chart
Packing content
EPROFILE HP · Mounting bracket · Power cord · Warranty card · User manual
4
INTRODUCTION
The EPROFILE HP is a high-output LED profile.
FEATURES
- Crisp gobo image projection, even at close range - Extremely flat field projection - Higher output than traditional 750W ellipsoidal reflector spotlights - 200W LED with extremely high light output - Flawless dimming with consistent color temperature throughout the dimming curve - Flicker-free output with selectable PWM frequencies for worry-free video - Quiet operation suitable for studio use - Power linking (PowerCon In/Out) - Rugged die-cast body and low-maintenance design - Master/Slave mode, Auto Shows - Manual control via onboard menu - Selection of four dimming curves - DMX control - Available lens tubes: 19° - 26° - 36° or 50° (not included)
SPECIFICATIONS
Light Source: Beam Angle: Output: Focus: Strobe: Dimming: Control: DMX Channels: Built-in Programs: Display: Mains: Consumption: Power connections: Data connections: Housing: Finish: IP rating: Cooling: Operating temperature: Max. Housing: Dimensions: Weight:
200W COB 3000K (CRI: 93) 19° / 26° / 36° / 50° 7232 / 5115 / 3330 / 1415 LUX @ 5 meters Manual 0-30 Hz 4 dimming curve modes DMX 2 / 3 / 6 Yes OLED function menu with 4 touch buttons 100V-240V, 50/60 Hz 205W Neutrik PowerCon In/Out 5-pin XLR In/Out for DMX Diecast aluminium Matte black IP20 Active (variable speed fan) 0°C to 40°C 54°C 528 x 342 x 526 mm 7.11 KG
5
MAINTENANCE
MAINTENANCE AND CLEANING THE UNIT · Make sure the area below the installation place is free from unwanted persons during setup.
· All screws used for installing the device and any of its parts should be tightly fastened and should not be corroded.
deformation. · The main cables must be in impeccable condition and should be replaced immediately even when a
small problem is detected. · It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or
other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might penetrate the unit and cause damage to it.
FUSE REPLACEMENT
1. Disconnect this product from the power outlet.
2. Using a screwdriver, unscrew the fuse holder cap from the housing.
3. Remove the blown fuse and replace with a good fuse of the same type and rat-
ing (250V/T3.15A).
4. Screw the fuse holder cap back in place and reconnect power.
TROUBLESHOOTING
Problems
Possible causes
Checks an d remedies
Fixture does not light up
· No mains supply · Dimmer fader set to 0 · Faulty LED · Faulty LED board
· Check the power supply voltage
· Increase the value of the dimmer channels
· Replace the LED board
· Replace the LED board
General low light intensity Fixture does not power up
· Dirty lens assembly · Misaligned lens assembly
· No power · Loose or damaged power cord · Faulty internal power supply
·
· Installle ns assembly properly
· Check for power on power outlet · Check power cord · Replace internal power supply
Contact an authorized service center in case of technical problems or not reported in the table can not be resolved by the procedure given in the table.
6
OVERVIEW
Focus knob
Gobo holder slot
Barrel rotation knob
Handle
Lens tube (sold separately)
Accessory
holder
slot
Framing
shutter (x 4)
Menu display
Menu navigation buttons
PowerCon In & Out
Bracket tightening knob
DMX In & Out
Mounting bracket
7
DIMENSIONS
8
DISPLAY MENU FUNCTIONS
OPERATION
- DMX Address: Assign DMX starting address to the EPROFILE HP
- DMX Mode: Select either 2-, 3- or 6-channel mode
- Static: Manually set dimming level and strobe rate
- Auto Show: Select one of four preprogrammed shows
- Master/Slave: Set the EPROFILE HP to function either as a master or slave when linking multiple units
- Dimmer Mode: Select the preferred dimming curve (1 = fast, 2 = medium, 3 = slow)
- LED Frequency: Select the preferred frequency (for achieving flicker-free video playback)
- Fan Mode: Select either variable speed (Auto) or always on (High)
- Back Light: Set display to darken after 10, 20 or 30 seconds, or set to always on (On)
- Information: View operating hours, sofware version and unit ID
DMX FUNCTIONS
- 2-Channel Mode: Controls dimming from 0 ~ 100% and LED frequency selection
- 3-Channel Mode: Adds strobe function
- 6-Channel Mode: Controls dimming, strobe, auto program selection, program speed, dimming curve selection and LED frequency selection
DMX PIN DIAGRAM
DMX - INPUT XLR plug
DMX - OUTPUT XLR socket
Pin1 : GND - Shield Pin2 : - Negative Pin3 : + Positive Pin4 : N/C Pin5 : N/C
9
MENU FUNCTIONS
MENU
UP
ENTER
DOWN
MENU
UP
DOWN
ENTER
Used to access the menu or to return a previous menu option
Navigates downwards through the menu list and increases the numeric value when in a function
Navigates upwards through the menu list and decreases the numeric value when in a function
Used to select and store the
current function value or option within a menu
Function DMX Address DMX Mode Static Auto Show Master/Slave Dimmer Mode
LED Frequency
Fan Mode Back Light Information
Options
<001 ~ 512> 2Ch 3Ch 6Ch Dimmer Strobe Auto1 Auto2 Auto3 Auto4 Master Slave Off Dimmer1 Dimmer2 Dimmer3 600Hz 1200Hz 2000Hz 4000Hz 25KHz Auto High On 10S 20S 30S Fixture Hours Version UID: 030F00600001
Values
<0-255> <0-255> <1-100> <1-100> <1-100> <1-100>
<9999> <v1.0>
Notes
Default001 Default6CH Default Dimmer: 255 / Strobe: 0 DefaultAuto 4 / Speed: 100
DefaultSlave
DefaultOff Sets dimmer curve
Default1200Hz
Default: Auto
DefaultOn Sets delay (in seconds)
10
PHOTOMETRICS
Beam Angle: 19°
Full 0
Distance (m) Luminance (lux)
1m
3m
5m
7m 10m
Beam Angle: 26°
Full 0
Distance (m) Luminance (lux)
1m
3m
5m
7m 10m
Beam Angle: 36°
Full 0
Distance (m) Luminance (lux)
1m
3m
5m
7m 10m
Beam Angle: 50°
Full 0
Distance (m) Luminance (lux)
1m
3m
5m
7m 10m
11
2-CHANNEL MODE
Channel 1 2
3-CHANNEL MODE
1 2
3
DMX CHARTS
Function Dimmer LED Frequency
Value 000-255 See chart below
Description 0100%
Dimmer Strobe LED Frequency
000-255 000-010 011-255 See chart below
0100% No Function Slow to Fast
6-CHANNEL MODE
Channel 1
Function Dimmer
2
Strobe
3
Auto Programs
4
Program Speed
5
Dimmer curve
6
LED Frequency
Value 000-255 000-010 011-255 000-010 011-070 071-130 131-190 191-255 000-255 000-051 052-101 102-152 153-203 204-255 000-010 011-050 051-100 101-150 151-200 201-255
0100%
Description
No Function
Slow to Fast
No Function
Auto Program 1
Auto Program 2
Auto Program 3
Auto Program 4
0 ~ 100%
Preset dimmer speed from display menu
Dimmer curve off
Dimmer curve mode 1 (fast speed)
Dimmer curve mode 2 (medium speed)
Dimmer curve mode 3 (slow speed)
Use frequency set via onboard menu
600Hz
1200Hz
2000Hz
4000Hz
25KHz
E K I N C .
Address: NO.55 Zhongzhun Road, Cuiheng New District, Zhongshan City, Guangdong Province Phone: 0086 (0760) 88280099 www.eklights.com