mailto:sales@redvisioncctv.commailto:techsupport@redvisioncctv.com
CCTV PTZ Security Cameras and Domes | PIR Detectors | UK Manufacturer | Redvision CCTVCCTV PTZ Security Cameras and Domes | PIR Detectors | UK Manufacturer | Redvision CCTV
Installation Guide for Redvision models including: RV-HUB-1 Redvision CCTV Hub, RV-HUB-1, Redvision CCTV Hub, CCTV Hub
2022 Hub Install Guide v2.0 5 ii. Safety guide 1. Installation of this system must be carried out by a skilled person in accordance with local electrical codes.
Redvision CCTV Hub™ | Redvision CCTV
File Info : application/pdf, 16 Pages, 1,002.00KB
DocumentDocumentRedvision CCTV Hub This Guide covers these products: RV-HUB-1 RV-24-HUB-1 RV-HUB-2/4 RV-24-HUB-2/4 Quick guide on page 4! Revision v2.0 Proud UK Design and Manufacture-----UK Service and Support Contents i. Quick-Guide for essential configuration: ..................................................................................................................3 ii. Safety guide ...............................................................................................................................................................5 1.0 Installing the Hub ....................................................................................................................................................7 1.1 Pole Mounted......................................................................................................................................................7 1.2 Wall Mounted .....................................................................................................................................................9 1.3 Camera installation .......................................................................................................................................... 11 2.0 Power supply installation & setup ...................................................................................................................... 12 2.1 Power supply specifications ............................................................................................................................ 12 2.2 24VDC Power supply layout ............................................................................................................................ 13 2.3 24VDC PSU connections .................................................................................................................................. 13 2.4 Mains power connections............................................................................................................................... 13 2.6 Hub Network and Power Connections ............................................................................................................ 14 3.0 Technical Specifications ....................................................................................................................................... 15 4.0 Warranty information.......................................................................................................................................... 16 Contact Redvision: Redvision CCTV Ltd. Alpha House Blacknest Road Blacknest Alton Hampshire GU34 4PX Sales & Technical Support: +44 (0) 1420 448 448 sales@redvisioncctv.com techsupport@redvisioncctv.com Welcome to Redvision Thank you for choosing Redvision. Your Hub has been carefully developed and manufactured in the United Kingdom. This guide is intended to cover the basic installation of your hub, up to and including accessing the internal web servers. 2 i. Quick-Guide for essential configuration: The hub uses a built-in web server, to allow configuration from any web-browser application. The table below lists the default configuration for the equipment on your Hub. To enable remote connections, do not change the network details without speaking with Redvision technical support. Hub defaults - with recorder Device Default IP 4G Router Recorder Camera Port 1 Camera Port 2 Camera Port 3 Camera Port 4 192.168.0.1 192.168.0.121 192.168.0.121:40001 192.168.0.121:40006 192.168.0.121:40011 192.168.0.121:40016 Default IP (Fixed Public IP Sim) 192.168.10.1 192.168.1.100 192.168.1.100:40001 192.168.1.100:40006 192.168.1.100:40011 192.168.1.100:40016 Default Username admin admin admin (if Redvision) admin (if Redvision) admin (if Redvision) admin (if Redvision) Default Password admin N/A admin (if Redvision) admin (if Redvision) admin (if Redvision) admin (if Redvision) Hub defaults with no recorder Device Default IP 4G Router Camera (if Redvision) 192.168.0.1 192.168.0.120 Default IP (Fixed Public IP Sim) 192.168.10.1 192.168.1.100 Default Username admin admin Default Password admin admin Connecting local to the hub: The Hub uses a 4G LTE router, with a dual LTE & Wi-Fi antenna. For hard wired connectivity, connect via the Hub's LAN port. Engineering configuration can be completed over the Wi-Fi connection, search for "Redvision CCTV Hub". The password will be the serial number of the unit (for security, please change this password when first connecting to the Hub). Connecting remotely to the hub: Redvision offer data packages with either a fixed public IP address, or a dynamic public IP address. The hub will be configured for connecting to each camera, or the recorder directly, as per the below. Hub defaults - with recorder Device DDNS Domain/ Fixed Public IP 4G Router See label on base of Hub (DDNS ONLY) Recorder See label on base of Hub Camera Port 1 See label on base of Hub Camera Port 2 See label on base of Hub Camera Port 3 See label on base of Hub Camera Port 4 See label on base of Hub Port 8888 11065 (N/A for fixed Public IP) 11071 11072 11073 11074 Hub defaults with no recorder Device DDNS Domain/ Fixed Public IP 4G Router See label on base of Hub (DDNS ONLY) Camera See label on base of Hub 2022 Hub Install Guide v2.0 Port 8888 11070 (N/A for fixed Public IP) 3 Router Login via web browser If connecting locally (over Wi-Fi or LAN), type the router's IP address into the web browser address bar; e.g. 192.168.0.1 and press enter. If connecting remotely, type in the DDNS followed by port 8888 e.g. rc303010.ddns.net:8888. The login page is then shown, as per below: · Enter the username and password. · The default user name is admin. The default password is admin. Change the password when you log in to the system for the first time to ensure system security. Recorder Login via web browser If connecting locally (over Wi-Fi or LAN), type the recorder's IP address into the web browser address bar; e.g. 192.168.0.121 and press enter. If connecting remotely, type in the DDNS followed by port 11065 e.g. rc303010.ddns.net:11065; or the fixed public IP address. The login page is then shown, as per below: · You will be prompted to setup a username and password upon first login to the system. 2022 Hub Install Guide v2.0 4 ii. Safety guide THIS CAMERA SYSTEM MUST BE INSTALLED, OPERATED AND MAINTAINED IN ACCORDANCE WITH THE MANUFACTURER'S SPECIFICATIONS. 1. Installation of this system must be carried out by a skilled person in accordance with local electrical codes. 2. This equipment must be connected to a protected earth. 3. This equipment has been designed to BS EN 62368-1:2020 and has no serviceable parts. 4. Do not open the equipment. 5. Do not drop the product. 6. Avoid the use of alcohol or solvent-based cleaners. The Hub should be cleaned with clean water and non-abrasive material. 7. The camera system should be installed where it cannot be tampered with by unauthorised personnel. 8. The products should be securely fastened to a structure of sufficient strength to support it. Allowance should be made for additional loads caused by local wind effects. 9. For best results, it is recommended once installed, that the hub be powered as soon as possible, to allow the internal heater and fan devices to operate. It is not recommended to leave the hub in storage or unpowered for extended periods of time. 2022 Hub Install Guide v2.0 5 iii. Router information Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the router is used in a normal manner with a well-constructed network, the router should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Redvision accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the router, or for failure of the router to transmit or receive such data. · The router generates radio frequency (RF) power. When using the router, care must be taken on safety issues related to RF interference as well as regulations of RF equipment. · Do not use your router in aircraft, hospitals, petrol stations or in places where using cellular products is prohibited. · Be sure that the router will not be interfering with nearby equipment. For example: pacemakers or medical equipment. The antenna of the router should be away from computers, office equipment, home appliance, etc. · An external antenna must be connected to the router for proper operation. Only uses approved antenna with the router. Please contact authorized distributor on finding an approved antenna. · Always keep the antenna with minimum safety distance of 20 cm or more from human body. Do not put the antenna inside metallic box, containers, etc. · RF exposure statements 1. For mobile devices without co-location (the transmitting antenna is installed or located morethan20cmaway from the body of user and nearby person) · FCC RF Radiation Exposure Statement 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and human body. 2022 Hub Install Guide v2.0 6 1.0 Installing the Hub 1.1 Pole Mounted Contents: - 1 x Hub Pole Bracket - 4 x M6 x 25 Hex Head Bolts - 4 x M6 Plain Nuts - 4 x M6 Nyloc Nuts - 4 x M6 Plain Washer 1) Using three off stainless steel Jubilee bands, fasten the pole bracket to the pole. Note, there are wide and narrow slots in the pole bracket, use the suitable slots for the pole diameter. 2022 Hub Install Guide v2.0 7 2) Using a M6 plain nut, M6 washer, and M6 Nylon Nut, secure 4 off M6 x 25 Hex Head bolts at the extremities of the Hub rails. Allow a sufficient gap between two off M6 nuts. M6 Plain Washer M6 Plain Nut M6 x 25 Hex Head M6 Nylon Nut 3) Slot the hub onto the pole bracket, ensuring the bracket is in the gap of the two M6 nuts. Fasten the M6 Nylon Nut to secure the Hub. 2022 Hub Install Guide v2.0 8 1.2 Wall Mounted It is important to use adequate quality fixings to safely support the complete Hub assembly when mounting the Hub to a wall. Contents: - 2 x Hub Wall Brackets - 4 x M6 x 12 CSK Bolts - 4 x M6 Plain Nuts - 1 x M4 Allen Key 1) Position the 4 off M6 Nuts in the rails (2 per each rail). It is recommended to locate the nuts towards the Hub extremities. 4 x M6 Plain Nut 2) Fix the 2 off Hub Wall Brackets to the Nuts using the 4 off M6 x 12 CSK Bolts. 4 x M6 CSK Bolts 2 x Hub Wall Brackets 2022 Hub Install Guide v2.0 9 3) Use the external mounting holes to fix the Hub to a wall. Wall Mounting Holes OBSERVE THE FOLLOWING PRECAUTIONS WHEN INSTALLING: 1. Mount the Hub in a position where it cannot be interfered with either intentionally or accidentally. 2. The mounting surface should be capable of supporting the weight of the hub, the camera(s) and mounting brackets under all expected conditions of load, vibration and temperature. 3. The mounting brackets should be fitted in accordance with instructions and should observe all appropriate safety precautions & local building regulations. 4. Ensure the Camera station is in the correct orientation. EMC Information WARNING: THIS IS A CLASS A PRODUCT. IF INSTALLED IN A STATIC ENVIRONMENT, RADIO INTERFERENCE MAY BE CAUSED, IN WHICH CASE THE USER MAY BE REQUIRED TO TAKE ADEQUATE MEASURES TO PREVENT IT. 2022 Hub Install Guide v2.0 10 1.3 Camera installation The Hub has been designed to allow up to 4 cameras to be directly mounted and powered. 1) Loosen (do not fully remove) the 4 off M6 Nylon nuts on the side plates and slide the camera mount assembly away from the main Hub enclosure. Loosen 4 off M6 Nuts 2) Connect cables as required to associated Hub ports, and run through the 30mm extrusion holes. Note, please ensure correct weatherproofed cable fittings are used. WARNING: Only use Redvision supplied Hub mains cable to power mains version of Hub. 3) Slide the camera mount assembly back flush with the main Hub enclosure, and fasten the 4 off M6 nuts on the side plates to secure. 4) Connect associate camera brackets to the Hub rails, and mount the cameras. 2022 Hub Install Guide v2.0 11 2.0 Power supply installation & setup WARRANTY & SAFETY NOTICE: DISCONNECT ALL POWER BEFORE WORKING ON THE HUB. INSTALLATION MUST BE CARRIED OUT BY A SUITABLY QUALIFIED PERSON UMBILICAL CABLE: A pre-made cable with connector must be purchased with all Redvision Hubs. The female connector connects directly to the male connector on the base of the Hub. · If a 24VDC version, mount the Redvision PSU in a position so it cannot be interfered with intentionally or accidentally. Ideally use a lockable cabinet. · If a 24VDC version, securely fix the Redvision PSU using appropriate size screws and ensure the cable glands have sufficient clearance to allow the cables to enter. · Ensure cable glands face downwards at all times, and securely tightened. · If a 24VDC version, all cables should be channelled through the appropriately sized gland holes. · Only use Redvision supplied umbilical/multicore cables for connecting the Hub. Warranty will be void if these cables are extended between the camera and PSU. Extending cables could also compromise safety. Contact Redvision Technical Support if in doubt. 2.1 Power supply specifications Mains versions: Power input voltage range Frequency range Max. output power Operating temperature range 24VDC versions: Power input voltage Max. output power Operating temperature range 100-240 VAC 50/60Hz 140W -10°C ~ + 50°C 24VDC 120W -10°C ~ + 50°C 2022 Hub Install Guide v2.0 12 2.2 24VDC Power supply layout It is the installer's responsibilty that a regulated 24VDC, 5A supply is used for powering the Hub. 2.3 24VDC PSU connections Umbilical Wire 24VDC POWER +24VDC BROWN 24VDC 0VDC BLUE 0VDC EARTH GREEN/YELLOW SAFETY: ENSURE MAINS INPUT & EARTH CONNECTIONS ARE SECURELY STRAIN RELIEVED. CAUTION: TAKE CARE WITH POLARITY OF POWER CONNECTIONS 2.4 Mains power connections Umbilical Wire MAINS POWER L LIVE (BROWN) 100/240 VAC N NEUTRAL (BLUE) EARTH GREEN/YELLOW SAFETY: ENSURE MAINS INPUT & EARTH CONNECTIONS ARE SECURELY STRAIN RELIEVED. CAUTION: ENSURE EARTH IS CONNECTED TO PROTECTED EARTH POINT. 2022 Hub Install Guide v2.0 13 2.6 Hub Network and Power Connections Ensure the hub is mounted with all connections facing down. The Hub is equipped with the following connections POE Port 3 15.5W 802.3af POE Port 1 90W 802.3bt/ 24VDC Camera Port POE Port 2 15.5W 802.3af Power input LAN port POE Port 4 15.5W 802.3af An IP67, weather-resistant cable-shroud is provided for each RJ45 port. This covers and protects the Cat5e cable and when mated with the RJ45 socket forms a complete IP67-rated connection. The Hub is provided with RJ45 connector caps for all RJ45 sockets. Ensure these are securely fitted for any unused connectors. This connector must be used at all times, camera/ Hub warranty may be invalidated otherwise. Cable-end shroud components Assembled Complete assembly 2022 Hub Install Guide v2.0 14 3.0 Technical Specifications 2022 Hub Install Guide v2.0 15 4.0 Warranty information Redvision CCTV limited (Redvision) warrants the buyer that the product will, on the date of shipment, be free from defects in material & workmanship and will conform to Redvision's specifications, provided to the buyer. If any defect in material or workmanship appears in the product, Redvision will, at its discretion, either repair or replace the defective product without charge at Redvision's customer service centre or authorised repair facility or credit or refund the purchase price of the defective product, provided: · The defect appears within 36 months from the date of purchase. · Examination of the product confirms that the claimed defect actually exists. Buyer shall follow Redvision's instructions regarding return of the defective product and no product will be accepted for repair, replacement, credit or refund without: · Buyer or an authorised representative of the buyer first contacting Redvision Technical Support for assistance and actual confirmation of suspected defect or fault. · Written authorisation of Redvision or in accordance with Redvision's written instructions, including an official Return Merchandise Authorisation number (RMA), issued by Redvision CCTV Ltd. In the case of any such return the buyer shall bear the risk of loss or damage and shall prepay all transportation charges to Redvision. The replaced product shall become Redvision's property. In no event shall Redvision be responsible for de-installation or reinstallation of the product or for the expenses thereof. If it is determined that returned product is not defective, the buyer shall pay Redvision all costs of handling, inspection, repairs and transportation at Redvision's then prevailing rates. With respect to product not manufactured by Redvision, to the extent permitted, extends the warranties and affords the remedies to the buyer given to Redvision by its vendor of said products. The foregoing warranties do not extend: · to expendable items, including SD Cards and Hard Disks · to experimental or development products · to product which has been subjected to misuse, neglect, accident or abuse; · to the unauthorised repair or alteration by anyone other than Redvision; · to improper installation, storage or maintenance by anyone other than Redvision; to product used in material violation of Redvision's instruction or to product which has had its serial number or month and year of manufacture or shipment removed, defaced or altered or to software. The term "software" means a set of logical instructions and table of information which guide the functioning of a processor. Such set may be contained in any medium whatsoever including, without limitation, hardware containing a pattern of bits representing such set, provided, however, the term "software" does not mean or include the medium. Redvision shall charge for the repair of all product returned out of warranty. Call Redvision customer service +44 (0)1420 448 448 for an RMA number or visit www.redvisioncctv.com for more information. 2022 Hub Install Guide v2.0 16 Copyright © 2008 - 2023 Redvision CCTV Ltd. Content subject to change without prior notice. E&OE. All rights reserved. Redvision CCTV Limited, Alpha House, Blacknest Road, Blacknest, Alton, GU34 4PX, United Kingdom Company registration: UK3952814 ©Redvision CCTV Ltd. 2020 Content is subject to change without prior notification E&EO. All Rights Reserved.