Humminbird HELIX 5 Series In-Dash Mounting Installation Guide

Installation Overview

This guide provides instructions for the in-dash mount installation of the HELIX 5 control head. It is recommended to read this guide before starting to understand the installation requirements.

Technical Support: For missing items or assistance, visit humminbird.com or contact Humminbird Technical Support through their Help Center at https://humminbird-help.johnsonoutdoors.com/hc/en-us.

Supplies: In addition to the supplied hardware, you will need a drill with various bits, a cutting tool, safety glasses, a dust mask, rubbing alcohol, and masking tape.

NOTE: Illustrations may differ from your product but the function remains the same.

1 Plan the Mounting Location

Choose a suitable, flat area on the dashboard for mounting. Consider the following:

• Interference: Ensure adequate distance from electric motors or equipment that may cause electronic interference.
• Stability: The mounting area should be protected from waves, shock, vibration, and water.
• Depth: The mounting area needs at least 3 inches (7.62 cm) of depth for the control head and cables.
• Ventilation: The area beneath the mounting surface should be well-ventilated.
• Accessibility: The location must allow easy access for all cables to reach the control head ports.

NOTE: If cables are too short, extension cables are available. Contact Humminbird Technical Support for assistance.

HELIX 5 Series In-Dash Mounting Dimensions:

The control head has a width of 7.55 inches (191.77 mm) and a depth of 2.90 inches (73.66 mm).

2 Cut the In-Dash Mounting Hole

To in-dash mount the HELIX control head, begin by positioning the components on the intended installation surfaces.

1. Review the instructions, measurements, and cutting options on the In-dash Mounting Template.
2. Tape the template to the chosen in-dash mounting location.
3. Select the best cutting method for your boat using the template:
   • Drill an entry hole large enough for your cutting tool's blade, away from the main cut line.
   • Alternatively, drill a corner hole (approx. 0.42 inches / 10.7 mm diameter) away from the main cut line, repeating for all four corners as indicated on the template. Use one corner hole as an entry hole or drill an additional one.
4. Carefully cut along the inside of the cut line around the template.
5. Test the Mounting Hole: Insert the control head into the mounting hole to check the fit. Make necessary adjustments. Remove the template.
6. Thoroughly clean and deburr the mounting hole.

3 Install the Control Head

1. Clean the Mating Surfaces: Use rubbing alcohol to clean the edges of the in-dash mounting hole and the back rim of the control head where the gasket will be installed. Allow to dry completely.
2. Place the control head, screen-side down, on a towel on a stable surface.
3. Peel the brown liner from the gasket's adhesive backing.
4. Align the gasket around the control head rim, ensuring it is centered and has no uneven gaps.
5. Lightly press one side of the gasket onto the flat rim of the control head.
6. Confirm alignment and centering, then lightly press down on the remaining sides of the gasket. Adjust as needed.
7. Carefully peel the plastic film from the gasket.
8. Insert the control head through the mounting hole from the front of the dash. Press firmly around the sides of the control head for 20 seconds to secure the adhesive.

4 Route and Connect the Cables

1. Refer to the installation guides for each hardware component for power and optional equipment installation.
2. Route all cables (power, transducer, accessories) to the control head and insert the connectors into the correct ports on the back of the control head.

CAUTION! Do NOT mount cables where connectors could be submerged in water. If cables are in a splash-prone area, consider applying dielectric grease to the inside of connectors to prevent corrosion.

Your control head is now ready for operation. Refer to your control head operations manual for details.

Optional: Use a Y-cable to connect a Transducer and Speed Sensor Accessory.

1-Year Limited Warranty

Humminbird warrants to the original retail purchaser that its products are free from defects in materials and workmanship for one year from the original retail purchase date. Defective products covered by this warranty will be repaired or replaced at Humminbird's option, freight prepaid. Humminbird's sole responsibility is limited to the repair or replacement of defective products.

This warranty does not apply if the product has been:

• Improperly installed.
• Used in a non-recommended installation or for commercial applications.
• Damaged due to accident or abnormal operation.
• Repaired or modified by unauthorized entities.

Retain your original receipt as proof of purchase date for in-warranty service.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES, OBLIGATIONS OR LIABILITIES ON THE PART OF HUMMINBIRD AND WILL BE THE CUSTOMER'S EXCLUSIVE REMEDY, EXCEPT FOR ANY APPLICABLE IMPLIED WARRANTIES UNDER STATE LAW WHICH ARE HEREBY LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. IN NO EVENT WILL HUMMINBIRD BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE PRODUCTS.

Some states do not allow limitations on implied warranties or the exclusion of incidental or consequential damages, so these exclusions may not apply to you. You may also have other rights that vary by state.

Humminbird Service Policy

Humminbird aims to repair units within three business days of receipt at the factory, excluding shipping time. Factory-serviced units undergo rigorous testing and quality control.

After the original warranty period, a standard flat rate service charge applies for repairs (physical damage and missing parts are extra). Repairs made after the original warranty are warranted for an additional 90 days.

Contact Technical Support or visit humminbird.com for current flat rate repair fees.

Humminbird reserves the right to deem any product unserviceable if replacement parts are unavailable. This Service Policy is valid in the United States only and applies to products returned to the Eufaula, Alabama factory. It is subject to change without notice.

Returning Your Unit for Service

Before sending your unit for repair, contact Humminbird by phone or email to obtain a Repair Authorization Number.

NOTE: Do not return your Humminbird to the store for service.

Have your product model name and serial number ready when contacting the factory. Include this information in email subject lines as well.

For IN-WARRANTY service:

• Obtain a Repair Authorization Number from Humminbird Technical Support.
• Tag the product with your name, address, phone number, and assigned Repair Authorization Number.
• Include a brief written description of the problem.
• Include a copy of your receipt for proof of purchase date.
• Return the product freight prepaid via an insured carrier with delivery confirmation.

For OUT-OF-WARRANTY service:

• Obtain a Repair Authorization Number from Humminbird Technical Support.
• Include payment (credit card number with expiration date, or money order; no cash).
• Tag the product with your name, address, phone number, and assigned Repair Authorization Number.
• Include a brief written description of the problem.
• Return the product freight prepaid via an insured carrier with delivery confirmation.

Contact Humminbird

Contact Humminbird Technical Support via their Help Center at https://humminbird-help.johnsonoutdoors.com/hc/en-us or in writing to:

Humminbird Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA

WARNING! Disassembly and repair should only be performed by authorized service personnel. Modifications to the serial number or unauthorized repairs will void the warranty.

NOTE: Product specifications and features are subject to change without notice.

ENVIRONMENTAL COMPLIANCE STATEMENT: Johnson Outdoors Marine Electronics, Inc. strives to be a responsible corporate citizen, operating in compliance with applicable environmental regulations.

WEEE DIRECTIVE: The EU Directive 2002/96/EC concerning Waste Electrical and Electronic Equipment (WEEE) impacts consumer electronics in the European Union. Producers are responsible for the environmentally responsible disposal of their products. EEE for transportation vehicles like automobiles, aircraft, and boats may be excluded from WEEE requirements in some EU member states.

The symbol [wheelie bin symbol] on the product indicates it must not be disposed of with household waste. It should be collected for recycling and recovery of waste EEE. Johnson Outdoors Marine Electronics, Inc. complies with the WEEE Directive. Contact your dealer or distributor for information on disposal and recycling requirements in your EU member state.